# Не работает WBIO DI-WD-14 **URL:** \ **Category:** Без категории\ **Created:** [February 20, 2021, 6:26am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160 "2021-02-20T06:26:41Z")\ **Posts on this page:** 16\ **Page:** 1
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 20, 2021, 6:26am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/1 "2021-02-20T06:26:41Z")
После 4х месяцев работы перестали работать модули ввода-вывода service wb-homa-gpio status ● wb-homa-gpio.service - LSB: MQTT Driver for GPIO-controlled switches Loaded: loaded (/etc/init.d/wb-homa-gpio; generated; vendor preset: enabled) Active: active (running) since Sat 2021-02-20 06:15:10 UTC; 7min ago Docs: man:systemd-sysv-generator(8) Process: 8310 ExecStop=/etc/init.d/wb-homa-gpio stop (code=exited, status=0/SUCCESS) Process: 8329 ExecStart=/etc/init.d/wb-homa-gpio start (code=exited, status=0/SUCCESS) CGroup: /system.slice/wb-homa-gpio.service └─8749 /usr/bin/wb-homa-gpio -c /tmp/wb-homa-gpio.do-not-edit.conf Feb 20 06:15:06 wirenboard-AILGVMR2 systemd[1]: Starting LSB: MQTT Driver for GPIO-controlled switches… Feb 20 06:15:10 wirenboard-AILGVMR2 wb-homa-gpio[8329]: Starting MQTT Driver for GPIO-controlled switches Feb 20 06:15:10 wirenboard-AILGVMR2 systemd[1]: Started LSB: MQTT Driver for GPIO-controlled switches. Я удалил все модули в веб интерфейсе ![image](https://support.wirenboard.com/uploads/default/original/2X/f/fe4bd926d55b1e0c17becb97541064782a4c1f49.png) Не понимаю что происходит Я даже на всякий случай закомментировал все скрипты - не помогло! dmesg [0.000000] Booting Linux on physical CPU 0x0 [0.000000] Linux version 4.9.22-wb6 (root@wbdevenv) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #2 SMP Tue Sep 1 06:27:21 UTC 2020 [0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [0.000000] CPU: div instructions available: patching division code [0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [0.000000] OF: fdt:Machine model: Wiren Board rev. 6.6.0 (i.MX6UL/ULL) [0.000000] cma: Reserved 16 MiB at 0x9f000000 [0.000000] Memory policy: Data cache writealloc [0.000000] On node 0 totalpages: 131072 [0.000000] free\_area\_init\_node: node 0, pgdat c0b4d880, node\_mem\_map deab3000 [0.000000] Normal zone: 1152 pages used for memmap [0.000000] Normal zone: 0 pages reserved [0.000000] Normal zone: 131072 pages, LIFO batch:31 [0.000000] percpu: Embedded 14 pages/cpu @defc8000 s25996 r8192 d23156 u57344 [0.000000] pcpu-alloc: s25996 r8192 d23156 u57344 alloc=14\*4096 [0.000000] pcpu-alloc: [0] 0 [0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920 [0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait ro [0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [0.000000] Memory: 491720K/524288K available (6144K kernel code, 312K rwdata, 2276K rodata, 1024K init, 342K bss, 16184K reserved, 16384K cma-reserved) [0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0700000 (7136 kB) .init : 0xc0a00000 - 0xc0b00000 (1024 kB) .data : 0xc0b00000 - 0xc0b4e140 ( 313 kB) .bss : 0xc0b50000 - 0xc0ba5aec ( 343 kB) [0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [0.000000] Hierarchical RCU implementation. [0.000000] Build-time adjustment of leaf fanout to 32. [0.000000] RCU restricting CPUs from NR\_CPUS=4 to nr\_cpu\_ids=1. [0.000000] RCU: Adjusting geometry for rcu\_fanout\_leaf=32, nr\_cpu\_ids=1 [0.000000] NR\_IRQS:16 nr\_irqs:16 16 [0.000000] Switching to timer-based delay loop, resolution 41ns [0.000015] sched\_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [0.000054] clocksource: mxc\_timer1: mask: 0xffffffff max\_cycles: 0xffffffff, max\_idle\_ns: 79635851949 ns [0.002559] Console: colour dummy device 80x30 [0.002601] Calibrating delay loop (skipped), value calculated using timer frequency… 48.00 BogoMIPS (lpj=240000) [0.002633] pid\_max: default: 32768 minimum: 301 [0.002902] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [0.002929] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [0.004414] CPU: Testing write buffer coherency: ok [0.004983] /cpus/cpu@0 missing clock-frequency property [0.005024] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [0.005080] Setting up static identity map for 0x80100000 - 0x80100070 [0.007721] Brought up 1 CPUs [0.007755] SMP: Total of 1 processors activated (48.00 BogoMIPS). [0.007770] CPU: All CPU(s) started in SVC mode. [0.009315] devtmpfs: initialized [0.035658] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [0.036437] clocksource: jiffies: mask: 0xffffffff max\_cycles: 0xffffffff, max\_idle\_ns: 19112604462750000 ns [0.036485] futex hash table entries: 256 (order: 2, 16384 bytes) [0.037873] pinctrl core: initialized pinctrl subsystem [0.040164] NET: Registered protocol family 16 [0.042337] DMA: preallocated 256 KiB pool for atomic coherent allocations [0.045253] cpuidle: using governor menu [0.079489] No ATAGs? [0.079541] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [0.079565] hw-breakpoint: maximum watchpoint size is 8 bytes. [0.081928] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [0.127830] mxs-dma 1804000.dma-apbh: initialized [0.132631] SCSI subsystem initialized [0.133241] usbcore: registered new interface driver usbfs [0.133398] usbcore: registered new interface driver hub [0.133677] usbcore: registered new device driver usb [0.135370] i2c-gpio i2c\_rtc: using pins 48 (SDA) and 49 (SCL) [0.136296] i2c-gpio i2c\_eeprom1: using pins 76 (SDA) and 67 (SCL) [0.137169] i2c-gpio i2c\_eeprom2: using pins 70 (SDA) and 71 (SCL) [0.138534] i2c i2c-1: IMX I2C adapter registered [0.138579] i2c i2c-1: can’t use DMA, using PIO instead. [0.138921] Linux video capture interface: v2.00 [0.139074] pps\_core: LinuxPPS API ver. 1 registered [0.139092] pps\_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [giometti@linux.it](mailto:giometti@linux.it) [0.139146] PTP clock support registered [0.139876] Advanced Linux Sound Architecture Driver Initialized. [0.142504] clocksource: Switched to clocksource mxc\_timer1 [0.168324] NET: Registered protocol family 2 [0.169611] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [0.169733] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [0.169890] TCP: Hash tables configured (established 4096 bind 4096) [0.170009] UDP hash table entries: 256 (order: 1, 8192 bytes) [0.170064] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [0.170371] NET: Registered protocol family 1 [0.171287] RPC: Registered named UNIX socket transport module. [0.171320] RPC: Registered udp transport module. [0.171336] RPC: Registered tcp transport module. [0.171352] RPC: Registered tcp NFSv4.1 backchannel transport module. [0.176272] workingset: timestamp\_bits=14 max\_order=17 bucket\_order=3 [0.195871] NFS: Registering the id\_resolver key type [0.195939] Key type id\_resolver registered [0.195956] Key type id\_legacy registered [0.206901] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [0.206934] io scheduler noop registered (default) [0.206953] io scheduler deadline registered [0.207033] io scheduler cfq registered [0.213852] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [0.213895] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [0.223349] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base\_baud = 5000000) is a IMX [0.802311] console [ttymxc0] enabled [0.807943] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 55, base\_baud = 5000000) is a IMX [0.851283] imx\_rngc 2284000.rngb: Freescale RNGC registered. [0.857416] [drm] Initialized [0.897247] brd: module loaded [0.916856] loop: module loaded [0.925112] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [0.936544] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [0.947403] libphy: Fixed MDIO Bus: probed [0.954076] 20b4000.ethernet supply phy not found, using dummy regulator [0.962091] pps pps0: new PPS source ptp0 [0.996502] libphy: fec\_enet\_mii\_bus: probed [1.002170] fec 20b4000.ethernet eth0: registered PHC device 0 [1.122657] 2188000.ethernet supply phy not found, using dummy regulator [1.243641] pps pps1: new PPS source ptp1 [1.248905] libphy: fec\_enet\_mii\_bus: probed [1.257039] fec 2188000.ethernet eth1: registered PHC device 1 [1.263598] PPP generic driver version 2.4.2 [1.268413] ehci\_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver [1.275093] ehci-mxc: Freescale On-Chip EHCI Host driver [1.280956] usbcore: registered new interface driver usb-storage [1.287577] usbcore: registered new interface driver usbserial [1.293729] usbcore: registered new interface driver usbserial\_generic [1.300390] usbserial: USB Serial support registered for generic [1.307099] mousedev: PS/2 mouse device common for all mice [1.371165] rtc-pcf8563 4-0051: rtc core: registered rtc-pcf8563 as rtc0 [1.387382] snvs\_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1 [1.396494] i2c /dev entries driver [1.410022] lm75 4-0048: hwmon0: sensor ‘lm75b’ [1.531106] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [1.539446] sdhci: Secure Digital Host Controller Interface driver [1.545778] sdhci: Copyright© Pierre Ossman [1.550165] sdhci-pltfm: SDHCI platform and OF driver helper [1.622588] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [1.642140] ledtrig-cpu: registered to indicate activity on CPUs [1.666807] usbcore: registered new interface driver usbhid [1.674567] usbhid: USB HID core driver [1.700509] NET: Registered protocol family 10 [1.707830] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [1.715707] NET: Registered protocol family 17 [1.720359] Key type dns\_resolver registered [1.729766] Registering SWP/SWPB emulation handler [1.736768] registered taskstats version 1 [1.760138] random: fast init done [1.767286] mmc0: new DDR MMC card at address 0001 [1.774415] imx\_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [1.785409] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB [1.790392] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB [1.809238] rtc-pcf8563 4-0051: setting system clock to 2021-02-20 05:38:43 UTC (1613799523) [1.817731] of\_cfs\_init [1.820543] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB [1.827061] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB [1.836077] of\_cfs\_init: OK [1.844589] mmcblk0: p1 p2 p3 p4 \< p5 p6 \> [1.849962] vdd3p0: disabling [1.856359] vref-3v3: disabling [1.859535] usb1\_vbus: disabling [1.862891] ALSA device list: [1.865872] No soundcards found. [1.870396] EXT4-fs (mmcblk0p3): couldn’t mount as ext3 due to feature incompatibilities [1.879362] EXT4-fs (mmcblk0p3): couldn’t mount as ext2 due to feature incompatibilities [1.895036] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [1.903453] VFS: Mounted root (ext4 filesystem) readonly on device 179:3. [1.915521] devtmpfs: mounted [1.919978] Freeing unused kernel memory: 1024K (c0a00000 - c0b00000) [2.164650] ip\_tables: © 2000-2006 Netfilter Core Team [2.201881] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [2.221065] systemd[1]: Detected architecture arm. [2.267459] systemd[1]: Set hostname to . [2.577733] systemd-sysv-generator[132]: [/etc/init.d/wb-mqtt-knx:6] Could not build name for facility $remote\_fs,: Invalid argument [2.901740] systemd[1]: Listening on Journal Socket (/dev/log). [2.933269] systemd[1]: Listening on Journal Socket. [2.964320] systemd[1]: Created slice System Slice. [3.004156] systemd[1]: Created slice system-systemd\x2dfsck.slice. [3.043485] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [3.094439] systemd[1]: Starting Load Kernel Modules… [3.110223] systemd[1]: Listening on udev Control Socket. [4.212772] EXT4-fs (mmcblk0p3): re-mounted. Opts: errors=remount-ro [4.615264] systemd-journald[149]: Received request to flush runtime journal from PID 1 [6.031802] lirc\_dev: IR Remote Control driver registered, major 245 [6.062870] Driver for 1-wire Dallas network protocol. [6.145982] lirc\_pwm: module is from the staging directory, the quality is unknown, you have been warned. [6.230919] lirc\_pwm lirc-rfm69: GPIO receiver on pin 77 [6.307592] lirc\_pwm lirc-rfm69: lirc\_dev: driver lirc-rfm69 registered at minor = 0 [6.372746] lirc\_pwm lirc-rfm69: probed [6.456509] fec 20b4000.ethernet rename2: renamed from eth0 [6.967401] fec 2188000.ethernet eth0: renamed from eth1 [7.009090] ci\_hdrc ci\_hdrc.0: EHCI Host Controller [7.029033] ci\_hdrc ci\_hdrc.0: new USB bus registered, assigned bus number 1 [7.044716] fec 20b4000.ethernet eth1: renamed from rename2 [7.152782] ci\_hdrc ci\_hdrc.0: USB 2.0 started, EHCI 1.00 [7.182909] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [7.189724] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [7.197055] usb usb1: Product: EHCI Host Controller [7.201947] usb usb1: Manufacturer: Linux 4.9.22-wb6 ehci\_hcd [7.207763] usb usb1: SerialNumber: ci\_hdrc.0 [7.504764] hub 1-0:1.0: USB hub found [7.552849] hub 1-0:1.0: 1 port detected [7.602241] 2184200.usb supply vbus not found, using dummy regulator [7.706027] ci\_hdrc ci\_hdrc.1: EHCI Host Controller [7.710985] ci\_hdrc ci\_hdrc.1: new USB bus registered, assigned bus number 2 [7.842661] ci\_hdrc ci\_hdrc.1: USB 2.0 started, EHCI 1.00 [7.880878] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [7.887826] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [7.895111] usb usb2: Product: EHCI Host Controller [7.900000] usb usb2: Manufacturer: Linux 4.9.22-wb6 ehci\_hcd [7.905781] usb usb2: SerialNumber: ci\_hdrc.1 [8.159625] hub 2-0:1.0: USB hub found [8.180746] hub 2-0:1.0: 1 port detected [8.622678] usb 2-1: new high-speed USB device number 2 using ci\_hdrc [8.769677] Adding 262140k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:262140k SS [8.843428] usb 2-1: New USB device found, idVendor=0424, idProduct=2514 [8.850183] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [8.895213] hub 2-1:1.0: USB hub found [8.900635] hub 2-1:1.0: 4 ports detected [9.083069] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [9.232846] usb 2-1.1: new high-speed USB device number 3 using ci\_hdrc [9.394406] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720 [9.401333] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [9.408824] usb 2-1.1: Product: 802.11n WLAN Adapter [9.413840] usb 2-1.1: Manufacturer: Realtek [9.418118] usb 2-1.1: SerialNumber: 00e04c000001 [9.583971] Bluetooth: Core ver 2.22 [9.615883] NET: Registered protocol family 31 [9.620353] Bluetooth: HCI device and connection manager initialized [9.675869] Bluetooth: HCI socket layer initialized [9.692041] Bluetooth: L2CAP socket layer initialized [9.706823] Bluetooth: SCO socket layer initialized [9.772698] usbcore: registered new interface driver btusb [9.785119] Bluetooth: hci0: rtl: examining hci\_ver=06 hci\_rev=000b lmp\_ver=06 lmp\_subver=8723 [9.793915] Bluetooth: hci0: rtl: loading rtl\_bt/rtl8723b\_config.bin [9.832859] bluetooth hci0: Direct firmware load for rtl\_bt/rtl8723b\_config.bin failed with error -2 [9.842053] Bluetooth: hci0: Failed to load rtl\_bt/rtl8723b\_config.bin [9.848729] Bluetooth: hci0: rtl: loading rtl\_bt/rtl8723b\_fw.bin [9.866086] Bluetooth: hci0: rom\_version status=0 version=1 [9.871792] Bluetooth: cfg\_sz 0, total size 22496 [10.244780] 8723bu: module is from the staging directory, the quality is unknown, you have been warned. [10.292734] RTL871X: module init start [10.296515] RTL871X: rtl8723bu v4.3.6.11\_12942.20141204\_BTCOEX20140507-4E40 [10.303616] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [10.529218] RTL871X: rtw\_ndev\_init(wlan0) [10.554052] RTL871X: rtw\_ndev\_init(wlan1) [10.577102] usbcore: registered new interface driver rtl8723bu [10.583102] RTL871X: module init ret=0 [12.593195] RTL871X: RTW\_ADAPTIVITY\_EN\_ [12.596887] AUTO, chplan:0x20, Regulation:3,3 [12.601283] RTL871X: RTW\_ADAPTIVITY\_MODE\_ [12.605227] NORMAL [12.907897] cgroup: new mount options do not match the existing superblock, will be ignored [13.053299] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [13.058641] Bluetooth: BNEP filters: protocol multicast [13.102857] Bluetooth: BNEP socket layer initialized [14.993296] IPv6: ADDRCONF(NETDEV\_UP): wlan0: link is not ready [17.044263] RTL871X: nolinked power save enter [18.397755] mcp230xx: probe of 1-0027 failed with error -11 [19.644970] mcp230xx: probe of 1-0026 failed with error -11 [21.039375] mcp230xx: probe of 1-0025 failed with error -11 [21.722620] random: crng init done [22.319822] mcp230xx: probe of 1-0023 failed with error -11 [25.183544] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 217, base\_baud = 5000000) is a IMX [36.652906] SMSC LAN8710/LAN8720 2188000.ethernet:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii\_bus:phy\_addr=2188000.ethernet:00, irq=-1) [36.787269] IPv6: ADDRCONF(NETDEV\_UP): eth0: link is not ready [37.213375] Micrel KSZ8081 or KSZ8091 2188000.ethernet:03: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii\_bus:phy\_addr=2188000.ethernet:03, irq=-1) [37.411070] IPv6: ADDRCONF(NETDEV\_UP): eth1: link is not ready [38.883169] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [40.563226] fec 20b4000.ethernet eth1: Link is Up - 100Mbps/Full - flow control off [41.126802] RTL871X: RTW\_ADAPTIVITY\_EN\_ [41.130496] AUTO, chplan:0x20, Regulation:3,3 [41.135019] RTL871X: RTW\_ADAPTIVITY\_MODE\_ [41.138887] NORMAL [43.825689] RTL871X: nolinked power save leave [44.147186] IPv6: ADDRCONF(NETDEV\_CHANGE): eth0: link becomes ready [44.231166] IPv6: ADDRCONF(NETDEV\_CHANGE): eth1: link becomes ready [44.696042] RTL871X: assoc success [44.699745] IPv6: ADDRCONF(NETDEV\_CHANGE): wlan0: link becomes ready [48.423144] unexport\_store: invalid GPIO 256 [48.427705] export\_store: invalid GPIO 256 [48.506884] unexport\_store: invalid GPIO 257 [48.511351] export\_store: invalid GPIO 257 [48.579550] unexport\_store: invalid GPIO 258 [48.629469] export\_store: invalid GPIO 258 [48.680489] unexport\_store: invalid GPIO 259 [48.721123] export\_store: invalid GPIO 259 [48.770694] unexport\_store: invalid GPIO 260 [48.819925] export\_store: invalid GPIO 260 [48.872683] unexport\_store: invalid GPIO 261 [48.917394] export\_store: invalid GPIO 261 [48.973212] unexport\_store: invalid GPIO 262 [49.022925] export\_store: invalid GPIO 262 [49.060274] unexport\_store: invalid GPIO 263 [49.108936] export\_store: invalid GPIO 263 [49.166140] unexport\_store: invalid GPIO 264 [49.170599] export\_store: invalid GPIO 264 [49.250827] unexport\_store: invalid GPIO 265 [49.319141] export\_store: invalid GPIO 265 [49.358010] unexport\_store: invalid GPIO 266 [49.415064] export\_store: invalid GPIO 266 [49.469479] unexport\_store: invalid GPIO 267 [49.520269] export\_store: invalid GPIO 267 [49.559738] unexport\_store: invalid GPIO 268 [49.611429] export\_store: invalid GPIO 268 [49.645020] unexport\_store: invalid GPIO 269 [49.687055] export\_store: invalid GPIO 269 [49.723109] unexport\_store: invalid GPIO 296 [49.780236] export\_store: invalid GPIO 296 [49.820623] unexport\_store: invalid GPIO 297 [49.875470] export\_store: invalid GPIO 297 [49.961490] unexport\_store: invalid GPIO 298 [50.013142] export\_store: invalid GPIO 298 [50.092100] unexport\_store: invalid GPIO 299 [50.172847] export\_store: invalid GPIO 299 [50.218450] unexport\_store: invalid GPIO 300 [50.263050] export\_store: invalid GPIO 300 [50.321594] unexport\_store: invalid GPIO 301 [50.360976] export\_store: invalid GPIO 301 [50.410242] unexport\_store: invalid GPIO 302 [50.455597] export\_store: invalid GPIO 302 [50.492819] unexport\_store: invalid GPIO 303 [50.533559] export\_store: invalid GPIO 303 [50.595451] unexport\_store: invalid GPIO 304 [50.632902] export\_store: invalid GPIO 304 [50.688007] unexport\_store: invalid GPIO 305 [50.732025] export\_store: invalid GPIO 305 [50.777921] unexport\_store: invalid GPIO 306 [50.840673] export\_store: invalid GPIO 306 [50.901150] unexport\_store: invalid GPIO 307 [50.942870] export\_store: invalid GPIO 307 [51.005178] unexport\_store: invalid GPIO 308 [51.009677] export\_store: invalid GPIO 308 [51.124928] unexport\_store: invalid GPIO 309 [51.187249] export\_store: invalid GPIO 309 [51.241700] unexport\_store: invalid GPIO 336 [51.294714] export\_store: invalid GPIO 336 [51.345685] unexport\_store: invalid GPIO 337 [51.427664] export\_store: invalid GPIO 337 [51.485272] unexport\_store: invalid GPIO 338 [51.524391] export\_store: invalid GPIO 338 [51.528898] unexport\_store: invalid GPIO 339 [51.595717] export\_store: invalid GPIO 339 [51.643734] unexport\_store: invalid GPIO 340 [51.676353] export\_store: invalid GPIO 340 [51.717462] unexport\_store: invalid GPIO 341 [51.764190] export\_store: invalid GPIO 341 [51.823801] unexport\_store: invalid GPIO 342 [51.896697] export\_store: invalid GPIO 342 [51.955698] unexport\_store: invalid GPIO 343 [51.992861] export\_store: invalid GPIO 343 [52.056220] unexport\_store: invalid GPIO 344 [52.123006] export\_store: invalid GPIO 344 [52.127535] unexport\_store: invalid GPIO 345 [52.263604] export\_store: invalid GPIO 345 [52.349276] unexport\_store: invalid GPIO 346 [52.423043] export\_store: invalid GPIO 346 [52.485692] unexport\_store: invalid GPIO 347 [52.546974] export\_store: invalid GPIO 347 [52.593647] unexport\_store: invalid GPIO 348 [52.636449] export\_store: invalid GPIO 348 [52.687534] unexport\_store: invalid GPIO 349 [52.722983] export\_store: invalid GPIO 349 [52.772143] unexport\_store: invalid GPIO 376 [52.816912] export\_store: invalid GPIO 376 [52.852208] unexport\_store: invalid GPIO 377 [52.890929] export\_store: invalid GPIO 377 [52.940202] unexport\_store: invalid GPIO 378 [52.981230] export\_store: invalid GPIO 378 [53.024884] unexport\_store: invalid GPIO 379 [53.063606] export\_store: invalid GPIO 379 [53.106497] unexport\_store: invalid GPIO 380 [53.110995] export\_store: invalid GPIO 380 [53.169272] unexport\_store: invalid GPIO 381 [53.202232] export\_store: invalid GPIO 381 [53.233025] unexport\_store: invalid GPIO 382 [53.237521] export\_store: invalid GPIO 382 [53.294781] unexport\_store: invalid GPIO 383 [53.337518] export\_store: invalid GPIO 383 [53.341993] unexport\_store: invalid GPIO 384 [53.440539] export\_store: invalid GPIO 384 [53.483401] unexport\_store: invalid GPIO 385 [53.546205] export\_store: invalid GPIO 385 [53.550720] unexport\_store: invalid GPIO 386 [53.624480] export\_store: invalid GPIO 386 [53.678026] unexport\_store: invalid GPIO 387 [53.723305] export\_store: invalid GPIO 387 [53.774166] unexport\_store: invalid GPIO 388 [53.811833] export\_store: invalid GPIO 388 [53.844066] unexport\_store: invalid GPIO 389 [53.890165] export\_store: invalid GPIO 389 [1854.726289] unexport\_store: invalid GPIO 256 [1854.743269] export\_store: invalid GPIO 256 [1854.760194] unexport\_store: invalid GPIO 257 [1854.764703] export\_store: invalid GPIO 257 [1854.772940] unexport\_store: invalid GPIO 258 [1854.783653] export\_store: invalid GPIO 258 [1854.789603] unexport\_store: invalid GPIO 259 [1854.799918] export\_store: invalid GPIO 259 [1854.805041] unexport\_store: invalid GPIO 260 [1854.812518] export\_store: invalid GPIO 260 [1854.821947] unexport\_store: invalid GPIO 261 [1854.826941] export\_store: invalid GPIO 261 [1854.839134] unexport\_store: invalid GPIO 262 [1854.843981] export\_store: invalid GPIO 262 [1854.851000] unexport\_store: invalid GPIO 263 [1854.856197] export\_store: invalid GPIO 263 [1854.863800] unexport\_store: invalid GPIO 264 [1854.873877] export\_store: invalid GPIO 264 [1854.879904] unexport\_store: invalid GPIO 265 [1854.885299] export\_store: invalid GPIO 265 [1854.892546] unexport\_store: invalid GPIO 266 [1854.897936] export\_store: invalid GPIO 266 [1854.908986] unexport\_store: invalid GPIO 267 [1854.914310] export\_store: invalid GPIO 267 [1854.921068] unexport\_store: invalid GPIO 268 [1854.925855] export\_store: invalid GPIO 268 [1854.933180] unexport\_store: invalid GPIO 269 [1854.939337] export\_store: invalid GPIO 269 [1854.944709] unexport\_store: invalid GPIO 296 [1854.951367] export\_store: invalid GPIO 296 [1854.956694] unexport\_store: invalid GPIO 297 [1854.963475] export\_store: invalid GPIO 297 [1854.969934] unexport\_store: invalid GPIO 298 [1854.974444] export\_store: invalid GPIO 298 [1854.981227] unexport\_store: invalid GPIO 299 [1854.986177] export\_store: invalid GPIO 299 [1854.995415] unexport\_store: invalid GPIO 300 [1855.001563] export\_store: invalid GPIO 300 [1855.006793] unexport\_store: invalid GPIO 301 [1855.013116] export\_store: invalid GPIO 301 [1855.020520] unexport\_store: invalid GPIO 302 [1855.025000] export\_store: invalid GPIO 302 [1855.035684] unexport\_store: invalid GPIO 303 [1855.042065] export\_store: invalid GPIO 303 [1855.047440] unexport\_store: invalid GPIO 304 [1855.054093] export\_store: invalid GPIO 304 [1855.060634] unexport\_store: invalid GPIO 305 [1855.072985] export\_store: invalid GPIO 305 [1855.084272] unexport\_store: invalid GPIO 306 [1855.089512] export\_store: invalid GPIO 306 [1855.094995] unexport\_store: invalid GPIO 307 [1855.102178] export\_store: invalid GPIO 307 [1855.107196] unexport\_store: invalid GPIO 308 [1855.113951] export\_store: invalid GPIO 308 [1855.120641] unexport\_store: invalid GPIO 309 [1855.131765] export\_store: invalid GPIO 309 [1855.136888] unexport\_store: invalid GPIO 336 [1855.143887] export\_store: invalid GPIO 336 [1855.155061] unexport\_store: invalid GPIO 337 [1855.163821] export\_store: invalid GPIO 337 [1855.171269] unexport\_store: invalid GPIO 338 [1855.176240] export\_store: invalid GPIO 338 [1855.186639] unexport\_store: invalid GPIO 339 [1855.192798] export\_store: invalid GPIO 339 [1855.199871] unexport\_store: invalid GPIO 340 [1855.204747] export\_store: invalid GPIO 340 [1855.212032] unexport\_store: invalid GPIO 341 [1855.216651] export\_store: invalid GPIO 341 [1855.223810] unexport\_store: invalid GPIO 342 [1855.230004] export\_store: invalid GPIO 342 [1855.235743] unexport\_store: invalid GPIO 343 [1855.242105] export\_store: invalid GPIO 343 [1855.247667] unexport\_store: invalid GPIO 344 [1855.254946] export\_store: invalid GPIO 344 [1855.262075] unexport\_store: invalid GPIO 345 [1855.266537] export\_store: invalid GPIO 345 [1855.307071] unexport\_store: invalid GPIO 346 [1855.330175] export\_store: invalid GPIO 346 [1855.346277] unexport\_store: invalid GPIO 347 [1855.352653] export\_store: invalid GPIO 347 [1855.357921] unexport\_store: invalid GPIO 348 [1855.365601] export\_store: invalid GPIO 348 [1855.371916] unexport\_store: invalid GPIO 349 [1855.377043] export\_store: invalid GPIO 349 [1855.384413] unexport\_store: invalid GPIO 376 [1855.392419] export\_store: invalid GPIO 376 [1855.397652] unexport\_store: invalid GPIO 377 [1855.404477] export\_store: invalid GPIO 377 [1855.425765] unexport\_store: invalid GPIO 378 [1855.458253] export\_store: invalid GPIO 378 [1855.477659] unexport\_store: invalid GPIO 379 [1855.500859] export\_store: invalid GPIO 379 [1855.505342] unexport\_store: invalid GPIO 380 [1855.535035] export\_store: invalid GPIO 380 [1855.540081] unexport\_store: invalid GPIO 381 [1855.550283] export\_store: invalid GPIO 381 [1855.554791] unexport\_store: invalid GPIO 382 [1855.561984] export\_store: invalid GPIO 382 [1855.566868] unexport\_store: invalid GPIO 383 [1855.574375] export\_store: invalid GPIO 383 [1855.582557] unexport\_store: invalid GPIO 384 [1855.591334] export\_store: invalid GPIO 384 [1855.596278] unexport\_store: invalid GPIO 385 [1855.603027] export\_store: invalid GPIO 385 [1855.609864] unexport\_store: invalid GPIO 386 [1855.615189] export\_store: invalid GPIO 386 [1855.622040] unexport\_store: invalid GPIO 387 [1855.627261] export\_store: invalid GPIO 387 [1855.634335] unexport\_store: invalid GPIO 388 [1855.641219] export\_store: invalid GPIO 388 [1855.646595] unexport\_store: invalid GPIO 389 [1855.654345] export\_store: invalid GPIO 389 Что делать?? ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 20, 2021, 6:27am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/2 "2021-02-20T06:27:31Z")
Модули удалил в hardware. Config сам после этого почистился. ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 20, 2021, 6:31am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/3 "2021-02-20T06:31:21Z")
сейчас посмотрел и скрипты service wb-rules status ● wb-rules.service - LSB: MQTT Rule Engine for Wiren Board Loaded: loaded (/etc/init.d/wb-rules; generated; vendor preset: enabled) Active: active (running) since Sat 2021-02-20 06:04:19 UTC; 25min ago Docs: man:systemd-sysv-generator(8) Process: 5959 ExecStop=/etc/init.d/wb-rules stop (code=exited, status=0/SUCCESS) Process: 5972 ExecStart=/etc/init.d/wb-rules start (code=exited, status=0/SUCCESS) CGroup: /system.slice/wb-rules.service └─5979 /usr/bin/wb-rules -syslog -editdir /etc/wb-rules /usr/share/wb-rules-system/rules/ /etc Feb 20 06:04:19 wirenboard-AILGVMR2 systemd[1]: Starting LSB: MQTT Rule Engine for Wiren Board… Feb 20 06:04:19 wirenboard-AILGVMR2 systemd[1]: Started LSB: MQTT Rule Engine for Wiren Board. При этом все скрипты закомментированы!!! ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 20, 2021, 6:50am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/4 "2021-02-20T06:50:32Z")
А теперь при попытке добавить обратно модули в etc/wb-hardware.conf вылезает ошибка ![image](https://support.wirenboard.com/uploads/default/original/2X/c/c2301502074cdfb4a5689f3679612c857f4293d4.png) ---
**Author:** ![BrainRoot](https://avatars.discourse-cdn.com/v2/letter/b/c2a13f/32.png) [@BrainRoot](https://support.wirenboard.com/u/BrainRoot)\ **Post date:** [February 20, 2021, 9:51am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/5 "2021-02-20T09:51:47Z")
Добрый день. Обновите пожалуйста штатным apt контроллер до актуального. ---
**Author:** ![BrainRoot](https://avatars.discourse-cdn.com/v2/letter/b/c2a13f/32.png) [@BrainRoot](https://support.wirenboard.com/u/BrainRoot)\ **Post date:** [February 22, 2021, 11:46am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/6 "2021-02-22T11:46:18Z")
Также прошу выполнить рекомендации вот отсюда: > [@Проблема с доступом к WB6 через Debug console на Ubuntu 20.04](https://support.wirenboard.com/t/problema-s-dostupom-k-wb6-cherez-debug-console-na-ubuntu-20-04/6905/22): > > Фикс готов: для установки Добавляем источник echo "deb http://releases.contactless.ru/experimental.15 stretch main" \> /etc/apt/sources.list.d/irq-test.list Обновляем систему с установкой пакетов: apt update && apt upgrade -y Тестируем версию wb-hwconf-manager: dpkg -s wb-hwconf-manager | grep Version Должно выдать “Version: 1.38.3” Веряию ядра: dpkg -s linux-image-4.9.22-wb6 | grep Version Должно выдать “Version: 4.9+wb20210202141020” Перезапускаем контроллер: reboot Прошу отписать… У вас проявляется довольно регдкий баг связанный с обработкой аппаратных прерываний центральным процессором контроллера. Мы баг устранили, но пока в основной репозитарий не выкладывали. ---
**Author:** ![cu6apum](https://avatars.discourse-cdn.com/v2/letter/c/74df32/32.png) [@cu6apum](https://support.wirenboard.com/u/cu6apum)\ **Post date:** [February 23, 2021, 1:56pm UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/7 "2021-02-23T13:56:42Z")
Опаньки. Подробнее можно? Зы. ALSA?!! ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 24, 2021, 4:02pm UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/9 "2021-02-24T16:02:33Z")
Error loading the file: Invalid config file - ошибка пи попытке зайти в /etc/wb-mqtt-gpio.conf ```auto root@wirenboard-AILGVMR2:~# service wb-mqtt-gpio status ● wb-mqtt-gpio.service - MQTT Driver for GPIO-controlled switches Loaded: loaded (/lib/systemd/system/wb-mqtt-gpio.service; disabled; vendor preset: enabled) Active: inactive (dead) root@wirenboard-AILGVMR2:~# service wb-mqtt-gpio start root@wirenboard-AILGVMR2:~# service wb-mqtt-gpio status ● wb-mqtt-gpio.service - MQTT Driver for GPIO-controlled switches Loaded: loaded (/lib/systemd/system/wb-mqtt-gpio.service; disabled; vendor preset: enabled) Active: activating (start-pre) since Wed 2021-02-24 15:51:22 UTC; 4s ago Process: 6125 ExecStart=/usr/bin/wb-mqtt-gpio (code=killed, signal=ABRT) Main PID: 6125 (code=killed, signal=ABRT); Control PID: 6134 (generate-system) CGroup: /system.slice/wb-mqtt-gpio.service └─control ├─6134 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6485 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6486 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6487 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6488 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6489 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6490 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6492 sed -r s/((\w+\s+){3})/\1\n/g ├─6493 od -A n -t u1 ├─6494 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh ├─6495 /bin/bash /usr/lib/wb-mqtt-gpio/generate-system-config.sh └─6497 sed -r s/((\w+\s+){4})/\1\n/g root@wirenboard-AILGVMR2:~# dmesg [0.000000] Booting Linux on physical CPU 0x0 [0.000000] Linux version 4.9.22-wb6 (root@wbdevenv) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #2 SMP Tue Feb 2 14:22:17 UTC 2021 [0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [0.000000] CPU: div instructions available: patching division code [0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [0.000000] OF: fdt:Machine model: Wiren Board rev. 6.6.0 (i.MX6UL/ULL) [0.000000] cma: Reserved 16 MiB at 0x9f000000 [0.000000] Memory policy: Data cache writealloc [0.000000] On node 0 totalpages: 131072 [0.000000] free_area_init_node: node 0, pgdat c0b4d880, node_mem_map deab3000 [0.000000] Normal zone: 1152 pages used for memmap [0.000000] Normal zone: 0 pages reserved [0.000000] Normal zone: 131072 pages, LIFO batch:31 [0.000000] percpu: Embedded 14 pages/cpu @defc8000 s25996 r8192 d23156 u57344 [0.000000] pcpu-alloc: s25996 r8192 d23156 u57344 alloc=14*4096 [0.000000] pcpu-alloc: [0] 0 [0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920 [0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait ro [0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [0.000000] Memory: 491720K/524288K available (6144K kernel code, 312K rwdata, 2280K rodata, 1024K init, 342K bss, 161 84K reserved, 16384K cma-reserved) [0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0700000 (7136 kB) .init : 0xc0a00000 - 0xc0b00000 (1024 kB) .data : 0xc0b00000 - 0xc0b4e140 ( 313 kB) .bss : 0xc0b50000 - 0xc0ba5aec ( 343 kB) [0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [0.000000] Hierarchical RCU implementation. [0.000000] Build-time adjustment of leaf fanout to 32. [0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [0.000000] NR_IRQS:16 nr_irqs:16 16 [0.000000] Switching to timer-based delay loop, resolution 41ns [0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [0.000054] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [0.002559] Console: colour dummy device 80x30 [0.002598] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [0.002630] pid_max: default: 32768 minimum: 301 [0.002898] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [0.002923] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [0.004405] CPU: Testing write buffer coherency: ok [0.004974] /cpus/cpu@0 missing clock-frequency property [0.005011] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [0.005071] Setting up static identity map for 0x80100000 - 0x80100070 [0.007708] Brought up 1 CPUs [0.007741] SMP: Total of 1 processors activated (48.00 BogoMIPS). [0.007758] CPU: All CPU(s) started in SVC mode. [0.009210] devtmpfs: initialized [0.035920] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [0.036691] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [0.036739] futex hash table entries: 256 (order: 2, 16384 bytes) [0.038134] pinctrl core: initialized pinctrl subsystem [0.040691] NET: Registered protocol family 16 [0.042611] DMA: preallocated 256 KiB pool for atomic coherent allocations [0.045493] cpuidle: using governor menu [0.080012] No ATAGs? [0.080066] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [0.080089] hw-breakpoint: maximum watchpoint size is 8 bytes. [0.082446] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [0.128435] mxs-dma 1804000.dma-apbh: initialized [0.133204] SCSI subsystem initialized [0.133819] usbcore: registered new interface driver usbfs [0.133999] usbcore: registered new interface driver hub [0.134264] usbcore: registered new device driver usb [0.135951] i2c-gpio i2c_rtc: using pins 48 (SDA) and 49 (SCL) [0.136858] i2c-gpio i2c_eeprom1: using pins 76 (SDA) and 67 (SCL) [0.137749] i2c-gpio i2c_eeprom2: using pins 70 (SDA) and 71 (SCL) [0.139238] i2c i2c-1: IMX I2C adapter registered [0.139279] i2c i2c-1: can't use DMA, using PIO instead. [0.139625] Linux video capture interface: v2.00 [0.139779] pps_core: LinuxPPS API ver. 1 registered [0.139800] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [0.139854] PTP clock support registered [0.140598] Advanced Linux Sound Architecture Driver Initialized. [0.143235] clocksource: Switched to clocksource mxc_timer1 [0.168754] NET: Registered protocol family 2 [0.170029] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [0.170157] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [0.170316] TCP: Hash tables configured (established 4096 bind 4096) [0.170434] UDP hash table entries: 256 (order: 1, 8192 bytes) [0.170491] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [0.170798] NET: Registered protocol family 1 [0.171725] RPC: Registered named UNIX socket transport module. [0.171756] RPC: Registered udp transport module. [0.171772] RPC: Registered tcp transport module. [0.171787] RPC: Registered tcp NFSv4.1 backchannel transport module. [0.176678] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [0.196334] NFS: Registering the id_resolver key type [0.196406] Key type id_resolver registered [0.196425] Key type id_legacy registered [0.207408] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [0.207442] io scheduler noop registered (default) [0.207460] io scheduler deadline registered [0.207541] io scheduler cfq registered [0.214169] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [0.214213] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [0.223158] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX [0.802507] console [ttymxc0] enabled [0.808172] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 55, base_baud = 5000000) is a IMX [0.851527] imx_rngc 2284000.rngb: Freescale RNGC registered. [0.857668] [drm] Initialized [0.897595] brd: module loaded [0.917242] loop: module loaded [0.925462] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [0.936907] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [0.947775] libphy: Fixed MDIO Bus: probed [0.954493] 20b4000.ethernet supply phy not found, using dummy regulator [0.962501] pps pps0: new PPS source ptp0 [0.996926] libphy: fec_enet_mii_bus: probed [1.002594] fec 20b4000.ethernet eth0: registered PHC device 0 [1.123385] 2188000.ethernet supply phy not found, using dummy regulator [1.244379] pps pps1: new PPS source ptp1 [1.249643] libphy: fec_enet_mii_bus: probed [1.257750] fec 2188000.ethernet eth1: registered PHC device 1 [1.264298] PPP generic driver version 2.4.2 [1.269143] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [1.275838] ehci-mxc: Freescale On-Chip EHCI Host driver [1.281682] usbcore: registered new interface driver usb-storage [1.288308] usbcore: registered new interface driver usbserial [1.294458] usbcore: registered new interface driver usbserial_generic [1.301122] usbserial: USB Serial support registered for generic [1.307866] mousedev: PS/2 mouse device common for all mice [1.371927] rtc-pcf8563 4-0051: rtc core: registered rtc-pcf8563 as rtc0 [1.388129] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1 [1.397245] i2c /dev entries driver [1.410697] lm75 4-0048: hwmon0: sensor 'lm75b' [1.531750] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [1.540085] sdhci: Secure Digital Host Controller Interface driver [1.546421] sdhci: Copyright(c) Pierre Ossman [1.550807] sdhci-pltfm: SDHCI platform and OF driver helper [1.623316] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [1.642820] ledtrig-cpu: registered to indicate activity on CPUs [1.669649] usbcore: registered new interface driver usbhid [1.677422] usbhid: USB HID core driver [1.701233] NET: Registered protocol family 10 [1.708566] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [1.716448] NET: Registered protocol family 17 [1.721103] Key type dns_resolver registered [1.730535] Registering SWP/SWPB emulation handler [1.737513] registered taskstats version 1 [1.762384] random: fast init done [1.768197] mmc0: new DDR MMC card at address 0001 [1.775261] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95 C [1.786250] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB [1.791262] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB [1.810155] rtc-pcf8563 4-0051: setting system clock to 2021-02-24 15:33:47 UTC (1614180827) [1.818650] of_cfs_init [1.821472] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB [1.827983] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB [1.836996] of_cfs_init: OK [1.845535] mmcblk0: p1 p2 p3 p4 < p5 p6 > [1.850678] vdd3p0: disabling [1.857319] vref-3v3: disabling [1.860495] usb1_vbus: disabling [1.863847] ALSA device list: [1.866827] No soundcards found. [1.871363] EXT4-fs (mmcblk0p3): couldn't mount as ext3 due to feature incompatibilities [1.880341] EXT4-fs (mmcblk0p3): couldn't mount as ext2 due to feature incompatibilities [1.890164] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem [1.897607] EXT4-fs (mmcblk0p3): write access will be enabled during recovery [1.985560] EXT4-fs (mmcblk0p3): orphan cleanup on readonly fs [2.017764] EXT4-fs (mmcblk0p3): 19 orphan inodes deleted [2.023344] EXT4-fs (mmcblk0p3): recovery complete [2.070627] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [2.078934] VFS: Mounted root (ext4 filesystem) readonly on device 179:3. [2.091520] devtmpfs: mounted [2.096651] Freeing unused kernel memory: 1024K (c0a00000 - c0b00000) [2.349194] ip_tables: (C) 2000-2006 Netfilter Core Team [2.375484] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTM P +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [2.394874] systemd[1]: Detected architecture arm. [2.448633] systemd[1]: Set hostname to . [2.771521] systemd-sysv-generator[133]: [/etc/init.d/wb-mqtt-knx:6] Could not build name for facility $remote_fs,: In valid argument [3.106076] systemd[1]: Listening on Journal Socket (/dev/log). [3.144374] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [3.185018] systemd[1]: Created slice System Slice. [3.218013] systemd[1]: Mounting /sys/kernel/config... [3.266702] systemd[1]: Created slice system-systemd\x2dfsck.slice. [3.315276] systemd[1]: Created slice system-serial\x2dgetty.slice. [3.354684] systemd[1]: Created slice User and Session Slice. [4.340428] EXT4-fs (mmcblk0p3): re-mounted. Opts: errors=remount-ro [4.799499] systemd-journald[152]: Received request to flush runtime journal from PID 1 [6.290105] lirc_dev: IR Remote Control driver registered, major 245 [6.305560] Driver for 1-wire Dallas network protocol. [6.383542] lirc_pwm: module is from the staging directory, the quality is unknown, you have been warned. [6.480354] lirc_pwm lirc-rfm69: GPIO receiver on pin 77 [6.539118] lirc_pwm lirc-rfm69: lirc_dev: driver lirc-rfm69 registered at minor = 0 [6.601632] lirc_pwm lirc-rfm69: probed [6.848304] fec 20b4000.ethernet rename2: renamed from eth0 [7.340723] fec 2188000.ethernet eth0: renamed from eth1 [7.351223] ci_hdrc ci_hdrc.0: EHCI Host Controller [7.393510] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [7.433122] fec 20b4000.ethernet eth1: renamed from rename2 [7.493402] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [7.559283] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [7.566241] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [7.573531] usb usb1: Product: EHCI Host Controller [7.578418] usb usb1: Manufacturer: Linux 4.9.22-wb6 ehci_hcd [7.584200] usb usb1: SerialNumber: ci_hdrc.0 [7.890260] hub 1-0:1.0: USB hub found [7.946464] hub 1-0:1.0: 1 port detected [7.998541] 2184200.usb supply vbus not found, using dummy regulator [8.047858] ci_hdrc ci_hdrc.1: EHCI Host Controller [8.052813] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [8.223406] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [8.240147] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [8.247114] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [8.254401] usb usb2: Product: EHCI Host Controller [8.259290] usb usb2: Manufacturer: Linux 4.9.22-wb6 ehci_hcd [8.265071] usb usb2: SerialNumber: ci_hdrc.1 [8.566831] hub 2-0:1.0: USB hub found [8.592030] hub 2-0:1.0: 1 port detected [9.003408] usb 2-1: new high-speed USB device number 2 using ci_hdrc [9.082034] Adding 262140k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:262140k SS [9.214312] usb 2-1: New USB device found, idVendor=0424, idProduct=2514 [9.223635] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [9.275769] hub 2-1:1.0: USB hub found [9.285479] hub 2-1:1.0: 4 ports detected [9.388334] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [9.633470] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [9.795429] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720 [9.802363] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [9.809818] usb 2-1.1: Product: 802.11n WLAN Adapter [9.814848] usb 2-1.1: Manufacturer: Realtek [9.819129] usb 2-1.1: SerialNumber: 00e04c000001 [9.981797] Bluetooth: Core ver 2.22 [10.051162] NET: Registered protocol family 31 [10.055776] Bluetooth: HCI device and connection manager initialized [10.085033] Bluetooth: HCI socket layer initialized [10.110683] Bluetooth: L2CAP socket layer initialized [10.117333] Bluetooth: SCO socket layer initialized [10.193609] usbcore: registered new interface driver btusb [10.207775] Bluetooth: hci0: rtl: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [10.216570] Bluetooth: hci0: rtl: loading rtl_bt/rtl8723b_config.bin [10.261907] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2 [10.271191] Bluetooth: hci0: Failed to load rtl_bt/rtl8723b_config.bin [10.277774] Bluetooth: hci0: rtl: loading rtl_bt/rtl8723b_fw.bin [10.294794] Bluetooth: hci0: rom_version status=0 version=1 [10.300504] Bluetooth: cfg_sz 0, total size 22496 [10.685443] 8723bu: module is from the staging directory, the quality is unknown, you have been warned. [10.743467] RTL871X: module init start [10.747247] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40 [10.754323] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [10.999308] RTL871X: rtw_ndev_init(wlan0) [11.019063] RTL871X: rtw_ndev_init(wlan1) [11.037802] usbcore: registered new interface driver rtl8723bu [11.043788] RTL871X: module init ret=0 [11.128058] usbcore: registered new interface driver rtl8xxxu [12.978817] cgroup: new mount options do not match the existing superblock, will be ignored [13.942025] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [13.947488] Bluetooth: BNEP filters: protocol multicast [13.983132] Bluetooth: BNEP socket layer initialized [14.173489] RTL871X: RTW_ADAPTIVITY_EN_ [14.177255] AUTO, chplan:0x20, Regulation:3,3 [14.181655] RTL871X: RTW_ADAPTIVITY_MODE_ [14.185613] NORMAL [17.067189] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [19.139894] RTL871X: nolinked power save enter [20.324670] random: crng init done [23.893011] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 217, base_baud = 5000000) is a IMX [38.863021] RTL871X: RTW_ADAPTIVITY_EN_ [38.866836] AUTO, chplan:0x20, Regulation:3,3 [38.871227] RTL871X: RTW_ADAPTIVITY_MODE_ [38.875110] NORMAL [40.934887] RTL871X: nolinked power save leave [41.403889] SMSC LAN8710/LAN8720 2188000.ethernet:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=218 8000.ethernet:00, irq=-1) [41.473875] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [41.686418] RTL871X: assoc success [41.689986] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [41.855729] Micrel KSZ8081 or KSZ8091 2188000.ethernet:03: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:ph y_addr=2188000.ethernet:03, irq=-1) [41.963983] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [43.605418] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [43.613130] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [45.364782] fec 20b4000.ethernet eth1: Link is Up - 100Mbps/Full - flow control off [45.408999] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready ``` UPD: отредактировал ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 24, 2021, 4:09pm UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/10 "2021-02-24T16:09:33Z")
root@wirenboard-AILGVMR2:/etc# service wb-homa-gpio status ● wb-homa-gpio.service - LSB: MQTT Driver for GPIO-controlled switches Loaded: loaded (/etc/init.d/wb-homa-gpio; generated; vendor preset: enabled) Active: active (exited) since Wed 2021-02-24 16:00:08 UTC; 7min ago Docs: man:systemd-sysv-generator(8) Process: 8719 ExecStop=/etc/init.d/wb-homa-gpio stop (code=exited, status=0/SUCCESS) Process: 8733 ExecStart=/etc/init.d/wb-homa-gpio start (code=exited, status=0/SUCCESS) CGroup: /system.slice/wb-homa-gpio.service Feb 24 16:00:08 wirenboard-AILGVMR2 systemd[1]: Starting LSB: MQTT Driver for GPIO-controlled switches… Feb 24 16:00:08 wirenboard-AILGVMR2 systemd[1]: Started LSB: MQTT Driver for GPIO-controlled switches. ---
**Author:** ![Zinkin\_Mitya](https://support.wirenboard.com/user_avatar/support.wirenboard.com/zinkin_mitya/32/4792_2.png) [@Zinkin\_Mitya](https://support.wirenboard.com/u/Zinkin_Mitya)\ **Post date:** [February 26, 2021, 3:02pm UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/11 "2021-02-26T15:02:17Z")
Покажите, что записано в файлах, через командную строку. `cat /etc/wb-hardware.conf ` ` cat /etc/wb-mqtt-gpio.conf` И еще посмотрите сколько свободно место, командой ` df -h` ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 28, 2021, 4:39am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/12 "2021-02-28T04:39:40Z")
root@wirenboard-AILGVMR2:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/root 976M 469M 441M 52% / devtmpfs 241M 0 241M 0% /dev tmpfs 249M 0 249M 0% /dev/shm tmpfs 249M 26M 224M 11% /run tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 249M 0 249M 0% /sys/fs/cgroup /dev/mmcblk0p6 1.3G 187M 1.1G 16% /mnt/data tmpfs 50M 0 50M 0% /run/user/0 ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 28, 2021, 4:41am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/13 "2021-02-28T04:41:25Z")
root@wirenboard-AILGVMR2:~# cat /etc/wb-hardware.conf { “slots”: [ { “id”: “wb6-mod1”, “name”: “Internal slot 1”, “compatible”: [ “wbe2”, “wbe3-reduced” ], “module”: “”, “options”: {} }, { “id”: “wb6-mod2”, “name”: “Internal slot 2”, “compatible”: [ “wbe2”, “wbe3-reduced” ], “module”: “”, “options”: {} }, { “id”: “wb6-mod3”, “name”: “Internal slot 3”, “compatible”: [ “wbe3”, “wbe3-reduced” ], “module”: “”, “options”: {} }, { “id”: “wb6-extio1”, “name”: “External I/O module 1”, “compatible”: [ “wb5-extio” ], “module”: “wbio-di-wd-14”, “options”: {} }, { “id”: “wb6-extio2”, “name”: “External I/O module 2”, “compatible”: [ “wb5-extio” ], “module”: “wbio-di-wd-14”, “options”: {} }, { “id”: “wb6-extio3”, “name”: “External I/O module 3”, “compatible”: [ “wb5-extio” ], “module”: “wbio-di-wd-14”, “options”: {} }, { “id”: “wb6-extio4”, “name”: “External I/O module 4”, “compatible”: [ “wb5-extio” ], “module”: “wbio-di-wd-14”, “options”: {} }, { “id”: “wb6-extio5”, “name”: “External I/O module 5”, “compatible”: [ “wb5-extio” ], “module”: “”, “options”: {} }, { “id”: “wb6-extio6”, “name”: “External I/O module 6”, “compatible”: [ “wb5-extio” ], “module”: “”, “options”: {} }, { “id”: “wb6-extio7”, “name”: “External I/O module 7”, “compatible”: [ “wb5-extio” ], “module”: “”, “options”: {} }, { “id”: “wb6-extio8”, “name”: “External I/O module 8”, “compatible”: [ “wb5-extio” ], “module”: “”, “options”: {} }, { “id”: “wb6-rs485-1”, “name”: “RS485-1 interface config”, “compatible”: [ “wb6-rs485” ], “module”: “wb6-can-rs485”, “options”: { “mode”: “enabled” } }, { “id”: “wb6-rs485-2”, “name”: “RS485-2/CAN interface config”, “compatible”: [ “wb6-rs485”, “wb6-can” ], “module”: “wb6-can-rs485”, “options”: { “mode”: “enabled” } }, { “id”: “wb6-w1”, “name”: “W1 terminal mode”, “compatible”: [ “wb6-wx” ], “module”: “wb6-wx-1wire”, “options”: {} }, { “id”: “wb6-w2”, “name”: “W2 terminal mode”, “compatible”: [ “wb6-wx” ], “module”: “wb6-wx-1wire”, “options”: {} } ] } ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 28, 2021, 4:44am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/14 "2021-02-28T04:44:29Z")
root@wirenboard-AILGVMR2:~# cat /etc/wb-mqtt-gpio.conf cat: /etc/wb-mqtt-gpio.conf: No such file or directory ---
**Author:** ![Andrej\_Mihajlovich](https://support.wirenboard.com/user_avatar/support.wirenboard.com/andrej_mihajlovich/32/4010_2.png) [@Andrej\_Mihajlovich](https://support.wirenboard.com/u/Andrej_Mihajlovich)\ **Post date:** [February 28, 2021, 5:20am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/15 "2021-02-28T05:20:51Z")
apt update && apt upgrade upgrade не запустился: dpkg was interrupted, you must manually run ‘dpkg --configure -a’ to correct the problem. root@wirenboard-AILGVMR2:/etc# dpkg --configure -a Все заработало ---
**Author:** ![cu6apum](https://avatars.discourse-cdn.com/v2/letter/c/74df32/32.png) [@cu6apum](https://support.wirenboard.com/u/cu6apum)\ **Post date:** [March 6, 2021, 1:36pm UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/16 "2021-03-06T13:36:22Z")
В итоге, что было? Я начинаю эти модули ставить, нужно бы превентивно знать про подводные ежики. ---
**Author:** ![BrainRoot](https://avatars.discourse-cdn.com/v2/letter/b/c2a13f/32.png) [@BrainRoot](https://support.wirenboard.com/u/BrainRoot)\ **Post date:** [March 9, 2021, 6:57am UTC](https://support.wirenboard.com/t/ne-rabotaet-wbio-di-wd-14/7160/17 "2021-03-09T06:57:11Z")
Для истории: Текущая версия wb-mqtt-gpio при сконфигурированных “лишних” модулях (в конфиге есть, физически нет) - ругается на ошибки и стартует без всех модулей этого типа (вход или выход). Это исправим.