U-Boot 2017.03-1.0.1-gf543a623ed (Mar 14 2019 - 14:32:12 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 55C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial EEPROM #0 MAC: 54:10:ec:ef:83:56 EEPROM #1 MAC: 54:10:ec:ef:0f:91 Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: 5v_out @ regulator@2 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: JetFlash Rev: 1100 Prod: Transcend 16GB Type: Removable Hard Disk Capacity: 15474.0 MB = 15.1 GB (31690752 x 512) reading wb6_update.fit 1 bytes read in 18 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update.fit ## Loading FIT struct to 0x820000c0 ... reading wb6_update.fit FAT: Misaligned buffer address (82002088) Skip 5057640 bytes of data reading wb6_update.fit FAT: Misaligned buffer address (82001414) Skip 44468 bytes of data reading wb6_update.fit FAT: Misaligned buffer address (82000654) Skip 4085 bytes of data Skip 229064206 bytes of data reading wb6_update.fit ** wb6_update.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update.fit ## Loading FIT struct to 0x820000c0 ... reading wb6_update.fit FAT: Misaligned buffer address (82002088) reading wb6_update.fit 5074216 bytes read in 3163 ms (1.5 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x820002c0 Data Size: 5057640 Bytes = 4.8 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 8d1af1df216a0e2f55c1eb7d4c81ac8b6fbb96f5 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... reading wb6_update.fit ## Loading FIT strings to 0x83000028 ... reading wb6_update.fit ## Loading FIT struct to 0x830000c0 ... reading wb6_update.fit FAT: Misaligned buffer address (83002088) Skip 5057640 bytes of data reading wb6_update.fit FAT: Misaligned buffer address (83001414) reading wb6_update.fit 61488 bytes read in 503 ms (119.1 KiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x83000440 Data Size: 44468 Bytes = 43.4 KiB Architecture: ARM Hash algo: sha1 Hash value: f9d735f903dafa43fd9cb5fa9e2bc7909f33d69c ## Verifying ... sha1+ Loading part 0 ... OK Kernel image @ 0x82000000 [ 0x000000 - 0x4d2c68 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef48000, end 9ef55db3 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.22-wb6 (root@wbdevenv) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #2 SMP Sat Jan 26 11:34:05 UTC 2019 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Wiren Board rev. 6.1 (i.MX6UL/ULL) [ 0.000000] cma: Reserved 16 MiB at 0x9f000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 14 pages/cpu @defc8000 s25932 r8192 d23220 u57344 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=usbupdate,wb6_update.fit [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 492248K/524288K available (6144K kernel code, 302K rwdata, 2264K rodata, 1024K init, 342K bss, 15656K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b4b9c0 ( 303 kB) [ 0.000000] .bss : 0xc0b4d000 - 0xc0ba282c ( 343 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000015] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000051] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002475] Console: colour dummy device 80x30 [ 0.002517] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002548] pid_max: default: 32768 minimum: 301 [ 0.002749] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002776] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.004158] CPU: Testing write buffer coherency: ok [ 0.004674] /cpus/cpu@0 missing clock-frequency property [ 0.004714] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004770] Setting up static identity map for 0x80100000 - 0x80100070 [ 0.007184] Brought up 1 CPUs [ 0.007217] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.007233] CPU: All CPU(s) started in SVC mode. [ 0.008433] devtmpfs: initialized [ 0.034297] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.035048] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.035098] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.036405] pinctrl core: initialized pinctrl subsystem [ 0.038629] NET: Registered protocol family 16 [ 0.040353] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.043458] cpuidle: using governor menu [ 0.077931] No ATAGs? [ 0.077986] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.078009] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.080229] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.124989] mxs-dma 1804000.dma-apbh: initialized [ 0.129542] SCSI subsystem initialized [ 0.130172] usbcore: registered new interface driver usbfs [ 0.130332] usbcore: registered new interface driver hub [ 0.130570] usbcore: registered new device driver usb [ 0.132418] i2c-gpio i2c_rtc: using pins 48 (SDA) and 49 (SCL) [ 0.133321] i2c-gpio i2c_eeprom1: using pins 76 (SDA) and 67 (SCL) [ 0.134225] i2c-gpio i2c_eeprom2: using pins 70 (SDA) and 71 (SCL) [ 0.135548] i2c i2c-1: IMX I2C adapter registered [ 0.135591] i2c i2c-1: can't use DMA, using PIO instead. [ 0.135934] Linux video capture interface: v2.00 [ 0.136092] pps_core: LinuxPPS API ver. 1 registered [ 0.136115] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.136169] PTP clock support registered [ 0.136916] Advanced Linux Sound Architecture Driver Initialized. [ 0.139371] clocksource: Switched to clocksource mxc_timer1 [ 0.163556] NET: Registered protocol family 2 [ 0.164776] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.164902] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.165058] TCP: Hash tables configured (established 4096 bind 4096) [ 0.165178] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.165232] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.165555] NET: Registered protocol family 1 [ 0.166400] RPC: Registered named UNIX socket transport module. [ 0.166432] RPC: Registered udp transport module. [ 0.166448] RPC: Registered tcp transport module. [ 0.166464] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.171247] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.187891] NFS: Registering the id_resolver key type [ 0.187958] Key type id_resolver registered [ 0.187976] Key type id_legacy registered [ 0.198099] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.198134] io scheduler noop registered (default) [ 0.198153] io scheduler deadline registered [ 0.198222] io scheduler cfq registered [ 0.204939] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.204983] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.213969] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX [ 0.793452] console [ttymxc0] enabled [ 0.799010] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 55, base_baud = 5000000) is a IMX [ 0.809309] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 56, base_baud = 5000000) is a IMX [ 0.852669] imx_rngc 2284000.rngb: Freescale RNGC registered. [ 0.858711] [drm] Initialized [ 0.896958] brd: module loaded [ 0.915968] loop: module loaded [ 0.924191] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 0.935607] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 0.949332] libphy: Fixed MDIO Bus: probed [ 0.955963] 20b4000.ethernet supply phy not found, using dummy regulator [ 0.964063] pps pps0: new PPS source ptp0 [ 0.996619] libphy: fec_enet_mii_bus: probed [ 1.002954] fec 20b4000.ethernet eth0: registered PHC device 0 [ 1.129521] 2188000.ethernet supply phy not found, using dummy regulator [ 1.250449] pps pps1: new PPS source ptp1 [ 1.255665] libphy: fec_enet_mii_bus: probed [ 1.263696] fec 2188000.ethernet eth1: registered PHC device 1 [ 1.270270] PPP generic driver version 2.4.2 [ 1.275075] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.281761] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.287591] usbcore: registered new interface driver usb-storage [ 1.294202] usbcore: registered new interface driver usbserial [ 1.300341] usbcore: registered new interface driver usbserial_generic [ 1.306997] usbserial: USB Serial support registered for generic [ 1.313654] mousedev: PS/2 mouse device common for all mice [ 1.364819] rtc rtc0: invalid alarm value: 2019-10-2 39:6:0 [ 1.371055] rtc-pcf8563 4-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 1.387125] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1 [ 1.396248] i2c /dev entries driver [ 1.409679] lm75 4-0048: hwmon0: sensor 'lm75b' [ 1.530260] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 1.538468] sdhci: Secure Digital Host Controller Interface driver [ 1.544807] sdhci: Copyright(c) Pierre Ossman [ 1.549194] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.619443] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 1.642051] ledtrig-cpu: registered to indicate activity on CPUs [ 1.656672] usbcore: registered new interface driver usbhid [ 1.664441] usbhid: USB HID core driver [ 1.696894] NET: Registered protocol family 10 [ 1.704064] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.711850] NET: Registered protocol family 17 [ 1.716518] Key type dns_resolver registered [ 1.725720] Registering SWP/SWPB emulation handler [ 1.732673] registered taskstats version 1 [ 1.757142] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 1.771272] random: fast init done [ 1.774737] mmc0: new DDR MMC card at address 0001 [ 1.792188] rtc-pcf8563 4-0051: setting system clock to 2019-09-05 07:54:40 UTC (1567670080) [ 1.800683] of_cfs_init [ 1.804062] mmcblk0: mmc0:0001 W62704 3.53 GiB [ 1.808968] mmcblk0boot0: mmc0:0001 W62704 partition 1 2.00 MiB [ 1.815371] mmcblk0boot1: mmc0:0001 W62704 partition 2 2.00 MiB [ 1.821828] of_cfs_init: OK [ 1.829679] mmcblk0rpmb: mmc0:0001 W62704 partition 3 512 KiB [ 1.838438] vdd3p0: disabling [ 1.841859] vref-3v3: disabling [ 1.845231] usb1_vbus: disabling [ 1.848556] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 1.852851] usb2_vbus: disabling [ 1.856098] ALSA device list: [ 1.859073] No soundcards found. [ 1.867116] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 1.874734] Please append a correct "root=" boot option; here are the available partitions: [ 1.883141] 0100 65536 ram0 [ 1.886722] (driver?) [ 1.889096] 0101 65536 ram1 [ 1.892715] (driver?) [ 1.895089] 0102 65536 ram2 [ 1.898667] (driver?) [ 1.901065] 0103 65536 ram3 [ 1.904642] (driver?) [ 1.907013] 0104 65536 ram4 [ 1.910615] (driver?) [ 1.912990] 0105 65536 ram5 [ 1.916566] (driver?) [ 1.918936] 0106 65536 ram6 [ 1.922563] (driver?) [ 1.924938] 0107 65536 ram7 [ 1.928514] (driver?) [ 1.930906] 0108 65536 ram8 [ 1.934486] (driver?) [ 1.936857] 0109 65536 ram9 [ 1.940458] (driver?) [ 1.942833] 010a 65536 ram10 [ 1.946495] (driver?) [ 1.948865] 010b 65536 ram11 [ 1.952558] (driver?) [ 1.954931] 010c 65536 ram12 [ 1.958593] (driver?) [ 1.960984] 010d 65536 ram13 [ 1.964649] (driver?) [ 1.967019] 010e 65536 ram14 [ 1.970705] (driver?) [ 1.973078] 010f 65536 ram15 [ 1.976742] (driver?) [ 1.979118] b300 3702784 mmcblk0 [ 1.982978] driver: mmcblk [ 1.985785] b301 16384 mmcblk0p1 9f5d196f-01[ 1.990942] [ 1.992448] b302 1048576 mmcblk0p2 9f5d196f-02[ 1.997587] [ 1.999089] b303 1048576 mmcblk0p3 9f5d196f-03[ 2.004249] [ 2.005754] b304 1 mmcblk0p4 [ 2.009966] [ 2.011472] b305 262144 mmcblk0p5 9f5d196f-05[ 2.016610] [ 2.018113] b306 1324032 mmcblk0p6 9f5d196f-06[ 2.023275] [ 2.024784] b318 512 mmcblk0rpmb [ 2.028967] (driver?) [ 2.031357] b310 2048 mmcblk0boot1 [ 2.035629] (driver?) [ 2.038000] b308 2048 mmcblk0boot0 [ 2.042296] (driver?) [ 2.044669] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 2.052941] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.22-wb6 #2 [ 2.059210] Hardware name: Freescale i.MX6 Ultralite (Device Tree) [ 2.065429] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 2.073191] [] (show_stack) from [] (dump_stack+0x8c/0xa8) [ 2.080429] [] (dump_stack) from [] (panic+0xd4/0x26c) [ 2.087324] [] (panic) from [] (mount_block_root+0x1a0/0x298) [ 2.094821] [] (mount_block_root) from [] (mount_root+0xf8/0x124) [ 2.102663] [] (mount_root) from [] (prepare_namespace+0x158/0x1bc) [ 2.110680] [] (prepare_namespace) from [] (kernel_init_freeable+0x194/0x1e4) [ 2.119566] [] (kernel_init_freeable) from [] (kernel_init+0x8/0x114) [ 2.127759] [] (kernel_init) from [] (ret_from_fork+0x14/0x3c) [ 2.135346] Rebooting in 10 seconds.. U-Boot 2017.03-1.0.1-gf543a623ed (Mar 14 2019 - 14:32:12 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 57C Reset cause: WDOG Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial EEPROM #0 MAC: 54:10:ec:ef:83:56 EEPROM #1 MAC: 54:10:ec:ef:0f:91 Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: 5v_out @ regulator@2 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: JetFlash Rev: 1100 Prod: Transcend 16GB Type: Removable Hard Disk Capacity: 15474.0 MB = 15.1 GB (31690752 x 512) reading wb6_update.fit 1 bytes read in 18 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ##############################