U-Boot SPL 2021.10-wb1.1.2-g0aab62b564 (Jul 27 2022 - 09:27:30 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x01160113 .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3e3f .p0_mpwrdlctl = 0x3f3f3835 .p0_mpwldectrl0 = 0x000d000d .p0_mpwldectrl1 = 0x000e000e Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.1.2-g0aab62b564 (Jul 27 2022 - 09:27:30 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 69C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=3 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: Could not get PHY for FEC0: addr 0 No ethernet found. Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... Bus usb@2184000: USB EHCI 1.00 Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80 USB device not accepting new address (error=22) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot switch to partitions #0, OK mmc1(part 0) is current device SD/MMC found on device 1 323 bytes read in 3 ms (104.5 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 5906504 bytes read in 257 ms (21.9 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard670 46734 bytes read in 6 ms (7.4 MiB/s) 485 bytes read in 3 ms (157.2 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 3 ms (194.3 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 4 ms (124 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 3 ms (108.4 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 3 ms (82 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x82000000 [ 0x000000 - 0x5a2048 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef78000, end 9ef9afff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb120+wb101 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GN2 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.7.0 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9f000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait ro [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 489388K/524288K available (8192K kernel code, 714K rwdata, 2652K rodata, 1024K init, 268K bss, 18516K reser) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x234/0x3dc with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000055] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002758] Console: colour dummy device 80x30 [ 0.002821] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002862] pid_max: default: 32768 minimum: 301 [ 0.003257] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003294] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.004867] CPU: Testing write buffer coherency: ok [ 0.005948] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.006831] devtmpfs: initialized [ 0.024376] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.024903] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.024949] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.026320] pinctrl core: initialized pinctrl subsystem [ 0.028339] NET: Registered protocol family 16 [ 0.030567] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.032618] thermal_sys: Registered thermal governor 'step_wise' [ 0.032903] cpuidle: using governor menu [ 0.213922] vdd1p1: supplied by regulator-dummy [ 0.225567] vdd3p0: supplied by regulator-dummy [ 0.237245] cpu: supplied by regulator-dummy [ 0.248874] vddsoc: supplied by regulator-dummy [ 0.582189] No ATAGs? [ 0.582249] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.582269] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.582865] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.583604] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.585103] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.585143] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.625480] mxs-dma 1804000.dma-apbh: initialized [ 0.630736] SCSI subsystem initialized [ 0.631252] usbcore: registered new interface driver usbfs [ 0.631376] usbcore: registered new interface driver hub [ 0.631492] usbcore: registered new device driver usb [ 0.632327] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.632457] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.633504] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.634267] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.634397] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.634982] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.635684] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.635808] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.636384] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.637967] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.638338] i2c i2c-1: IMX I2C adapter registered [ 0.639058] mc: Linux media interface: v0.10 [ 0.639178] videodev: Linux video capture interface: v2.00 [ 0.639315] pps_core: LinuxPPS API ver. 1 registered [ 0.639333] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.639390] PTP clock support registered [ 0.640018] Advanced Linux Sound Architecture Driver Initialized. [ 0.642027] clocksource: Switched to clocksource mxc_timer1 [ 0.659831] NET: Registered protocol family 2 [ 0.661010] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.661125] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.661230] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.661335] TCP: Hash tables configured (established 4096 bind 4096) [ 0.661523] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.661576] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.661899] NET: Registered protocol family 1 [ 0.662964] RPC: Registered named UNIX socket transport module. [ 0.662998] RPC: Registered udp transport module. [ 0.663015] RPC: Registered tcp transport module. [ 0.663030] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.664123] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.666965] Initialise system trusted keyrings [ 0.667404] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.679111] NFS: Registering the id_resolver key type [ 0.679199] Key type id_resolver registered [ 0.679215] Key type id_legacy registered [ 0.680121] Key type asymmetric registered [ 0.680156] Asymmetric key parser 'x509' registered [ 0.680258] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.680280] io scheduler mq-deadline registered [ 0.680298] io scheduler kyber registered [ 0.692274] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.692323] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.696216] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX [ 1.359792] printk: console [ttymxc0] enabled [ 1.366287] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX [ 1.410043] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.417478] random: fast init done [ 1.421423] random: crng init done [ 1.460929] brd: module loaded [ 1.479193] loop: module loaded [ 1.482775] at24 5-0050: supply vcc not found, using dummy regulator [ 1.494199] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.501176] at24 6-0050: supply vcc not found, using dummy regulator [ 1.512605] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.525038] libphy: Fixed MDIO Bus: probed [ 1.532188] pps pps0: new PPS source ptp0 [ 1.571663] libphy: fec_enet_mii_bus: probed [ 1.577162] fec 20b4000.ethernet ethFEC0: registered PHC device 0 [ 1.702720] pps pps1: new PPS source ptp1 [ 1.709318] libphy: fec_enet_mii_bus: probed [ 1.715604] mdio_bus 2188000.ethernet-2: MDIO device at address 3 is missing. [ 1.723823] fec 2188000.ethernet ethFEC1: registered PHC device 1 [ 1.730828] PPP generic driver version 2.4.2 [ 1.735689] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.742295] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.747961] usbcore: registered new interface driver usb-storage [ 1.754257] usbcore: registered new interface driver usbserial_generic [ 1.760865] usbserial: USB Serial support registered for generic [ 1.808997] rtc rtc0: invalid alarm value: 2016-11-06T02:77:00 [ 1.815279] rtc-pcf8563 4-0051: registered as rtc0 [ 1.831773] rtc-pcf8563 4-0051: setting system clock to 2016-11-03T20:48:21 UTC (1478206101) [ 1.849898] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1 [ 1.856512] i2c /dev entries driver [ 1.863374] lm75 4-0048: supply vs not found, using dummy regulator [ 1.874897] lm75 4-0048: hwmon0: sensor 'lm75b' [ 1.994441] sdhci: Secure Digital Host Controller Interface driver [ 2.000654] sdhci: Copyright(c) Pierre Ossman [ 2.005091] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.019013] ledtrig-cpu: registered to indicate activity on CPUs [ 2.026816] usbcore: registered new interface driver usbhid [ 2.032511] usbhid: USB HID core driver [ 2.048666] NET: Registered protocol family 10 [ 2.053291] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA [ 2.063666] Segment Routing with IPv6 [ 2.067763] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.075708] NET: Registered protocol family 17 [ 2.080455] Key type dns_resolver registered [ 2.089182] registered taskstats version 1 [ 2.093416] Loading compiled-in X.509 certificates [ 2.117524] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.129401] of_cfs_init [ 2.132222] of_cfs_init: OK [ 2.139915] ALSA device list: [ 2.143004] No soundcards found. [ 2.146717] Waiting for root device /dev/mmcblk0p3... [ 2.156279] mmc0: new DDR MMC card at address 0001 [ 2.161976] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.167007] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 2.173410] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 2.179636] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (245:0) [ 2.190259] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 2.209222] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem [ 2.216628] EXT4-fs (mmcblk0p3): write access will be enabled during recovery [ 3.194778] EXT4-fs (mmcblk0p3): recovery complete [ 3.202185] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 3.210481] VFS: Mounted root (ext4 filesystem) readonly on device 179:3. [ 3.218720] devtmpfs: mounted [ 3.225087] Freeing unused kernel memory: 1024K [ 3.230877] Run /sbin/init as init process [ 3.508516] systemd[1]: RTC configured in localtime, applying delta of 180 minutes to system time. [ 3.599204] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRY) [ 3.618366] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 3.663117] systemd[1]: Set hostname to . [ 3.906240] systemd-fstab-generator[91]: Checking was requested for "/mnt/data/var/log", but it is not a device. [ 4.138927] systemd[1]: [/lib/systemd/system/wb-mqtt-w1.service:10] Unknown lvalue 'StartLimitIntervalSec' in section 'Service' [ 4.313810] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 4.353801] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 4.385710] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. [ 4.433588] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 4.452897] systemd[1]: Mounting /sys/kernel/config... Mounting /sys/kernel/config... [ 4.512886] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ OK ] Created slice system-getty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. Mounting Debug File System... [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket. Starting Create list of required st…ce nodes for the current kernel... Starting File System Check on Root Device... Starting Load Kernel Modules... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Listening on Syslog Socket. Starting Journal Service... [ OK ] Reached target Remote File Systems. [ OK ] Listening on udev Kernel Socket. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted /sys/kernel/config. [ OK ] Started Journal Service. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started File System Check on Root Device. [ OK ] Started Load Kernel Modules. [ OK ] Started File System Check Daemon to report status. Starting Apply Kernel Variables... Starting Remount Root and Kernel File Systems... Starting Create Static Device Nodes in /dev... [ OK ] Started Apply[ 5.476219] EXT4-fs (mmcblk0p3): re-mounted. Opts: errors=remount-ro Kernel Variables. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting prepare partitions at first boot... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started prepare partitions at first boot. [ OK ] Reached target Local File Systems (Pre). [ 7.261773] Driver for 1-wire Dallas network protocol. [ OK ] Started udev Coldplug all Devices. [ 7.306683] gpio-68 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 7.379914] gpio-11 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ OK ] Found device /dev/ttymxc0. [ 7.665171] fec 20b4000.ethernet eth1: renamed from ethFEC0 [ 7.978197] fec 2188000.ethernet eth0: renamed from ethFEC1 [ 8.059330] imx_usb 2184000.usb: No over current polarity defined [ 8.127374] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 8.174080] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 8.272167] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 8.304541] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 8.312892] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.320122] usb usb1: Product: EHCI Host Controller [ 8.325038] usb usb1: Manufacturer: Linux 5.10.35-wb120+wb101 ehci_hcd [ 8.331585] usb usb1: SerialNumber: ci_hdrc.0 [ 8.619924] hub 1-0:1.0: USB hub found [ 8.626448] hub 1-0:1.0: 1 port detected [ 8.704794] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 8.709748] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 8.832170] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 8.852374] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 8.860665] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.867944] usb usb2: Product: EHCI Host Controller [ 8.872858] usb usb2: Manufacturer: Linux 5.10.35-wb120+wb101 ehci_hcd [ 8.879394] usb usb2: SerialNumber: ci_hdrc.1 [ OK ] Found device /dev/mmcblk0p5. [ 9.012191] usb usb1-port1: over-current condition [ 9.090672] hub 2-0:1.0: USB hub found [ 9.126165] hub 2-0:1.0: 1 port detected [ OK ] Found device /dev/mmcblk0p6. [ 9.522142] usb 2-1: new full-speed USB device number 2 using ci_hdrc Starting File System Check on /dev/mmcblk0p6... Activating swap /dev/mmcblk0p5... [ 9.668150] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SS [ OK ] Activated swap /dev/mmcblk0p5. [ OK ] Reached target Swap. [ 9.772165] usb 2-1: device descriptor read/64, error -71 [ 10.132135] usb 2-1: device descriptor read/64, error -71 [ OK ] Started File System Check on /dev/mmcblk0p6. Mounting /mnt/data... [ 10.402198] usb 2-1: new full-speed USB device number 3 using ci_hdrc [ 10.463379] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /mnt/data. Mounting /var/log... [ OK ] Mounted /var/log. [ OK ] Reached target Local File Systems. [ OK ] Started ifup for eth0. [ 10.662383] usb 2-1: device descriptor read/64, error -71 Starting prepare mounts and symlinks to config files... Starting Flush Journal to Persistent Storage... [ 10.841128] systemd-journald[108]: Received request to flush runtime journal from PID 1 [ 10.898615] systemd-journald[108]: File /var/log/journal/2778fff92b203689d1255acd631b4f98/system.journal corrupted or uncleanly. [ 11.032144] usb 2-1: device descriptor read/64, error -71 [ 11.152276] usb usb2-port1: attempt power cycle [ OK ] Started Flush Journal to Persistent Storage. [ 11.652181] usb 2-1: new full-speed USB device number 4 using ci_hdrc [ 12.152167] usb 2-1: device not accepting address 4, error -71 [ 12.322138] usb 2-1: new full-speed USB device number 5 using ci_hdrc [ OK ] Started prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ 12.839461] usb 2-1: device not accepting address 5, error -71 Starting Update UTMP about System Boot/Shutdown... [ 12.870253] usb usb2-port1: unable to enumerate USB device [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on KNX Daemon (socket). [ OK ] Started Monitor directories with device templates for wb-mqtt-serial. [ OK ] Reached target Paths. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Generates wb-mqtt-serial UI schema for wb-mqtt-confed. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... Starting LSB: Start/stop sysstat's sadc... Starting Login Service... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Cgroup management daemon. Starting System Logging Service... Starting Restore /etc/resolv.conf i…fore the ppp link was shut down... Starting Restore local d[ 14.317829] new mount options do not match the existing superblock, will be ignored ate from Wiren Board GSM RTC... [ OK ] Started Regular background program processing daemon. [ OK ] Started watch config files. Starting initialize filesystems at first boot... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. Starting Initialize Wiren Board Device Tree overlays... [ OK ] Started System Logging Service. [ OK ] Started Restore /etc/resolv.conf if…before the ppp link was shut down. [ OK ] Started Mosquitto MQTT v3.1/v3.1.1 Broker. [ OK ] Started Login Service. [ OK ] Started Wiren Board firmware update service. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Started Wiren Board configuration editor backend. Starting Wiren Board MQTT to Modbus TCP gateway... [ OK ] Started LSB: Start/stop sysstat's sadc. [ OK ] Started initialize filesystems at first boot. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Wiren Board MQTT to OPC UA gateway. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Wiren Board MQTT to Modbus TCP gateway. [ 22.092389] SMSC LAN8710/LAN8720 2188000.ethernet-2:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.et) [ 24.252497] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 24.260387] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started Restore local date from Wiren Board GSM RTC. [ 30.225135] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 224, base_baud = 5000000) is a IMX [ 30.884855] 2288000.serial: ttymxc7 at MMIO 0x2288000 (irq = 225, base_baud = 5000000) is a IMX [ OK ] Started Initialize Wiren Board Device Tree overlays. [ OK ] Started metrics sender.. [ OK ] Started MQTT Rule engine for Wiren Board. [ OK ] Started GateDaemon. [ OK ] Started one-click diagnostic data c…ard, generating archive with data. Starting Raise network interfaces... Starting KNXD Configurator for Wiren Board... [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Started Wiren Board journald to MQTT gateway. [ OK ] Started Wiren Board database logger. Starting dnsmasq - A lightweight DHCP and caching DNS server... [ OK ] Started MQTT Driver for serial devices. Starting MQTT Driver for GPIO-controlled switches... Starting MQTT Driver for ADC... Starting KNX Daemon... [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. Starting Permit User Sessions... Starting OpenBSD Secure Shell server... Starting A high performance web server and a reverse proxy server... [ OK ] Started Permit User Sessions. [ OK ] Started KNX Daemon. [ OK ] Reached target Network is Online. Starting LSB: Brings up/down network automatically... Starting /etc/rc.local Compatibility... Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Start NTP daemon... [ OK ] Started Wiren Board MQTT KNX bridge. [ 34.705279] rc.local[1790]: Unable to open device file /dev/bus/usb/002/002: No such file or directory [ 34.784703] rc.local[1790]: Unable to open device file /proc/bus/usb/002/002: No such file or directory [ 34.981824] rc.local[1790]: <13>Nov 3 20:48:54 root: WiFi was turned off from /etc/rc.local [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started OpenBSD Secure Shell server. [ 39.349141] process '/sbin/netplugd' started with executable stack [ 39.906853] fec 20b4000.ethernet eth1: Unable to connect to phy [ 40.757100] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ OK ] Started LSB: Start NTP daemon. [ 41.443923] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 41.617921] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 41.811922] cfg80211: failed to load regulatory.db [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Starting Compensation of systime in…evice-tree (with opposite sign)... [ OK ] Stopped Wiren Board MQTT KNX bridge. [ OK ] Started Wiren Board MQTT KNX bridge. [ OK ] Stopped Wiren Board journald to MQTT gateway. [ OK ] Started Wiren Board journald to MQTT gateway. [ OK ] Started Serial Getty on ttymxc0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Advanced IEEE 802.11 management daemon. [ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started A high performance web server and a reverse proxy server. Starting Initialize Wiren Board on successful boot... [ OK ] Started Compensation of systime in … device-tree (with opposite sign). [ OK ] Stopped Wiren Board MQTT KNX bridge. [ OK ] Started Wiren Board MQTT KNX bridge. [ OK ] Started LSB: Brings up/down network automatically. Stopping KNX Daemon... [ OK ] Stopped Wiren Board journald to MQTT gateway. [ OK ] Started Wiren Board journald to MQTT gateway. [ OK ] Stopped KNX Daemon. Starting KNX Daemon... Debian GNU/Linux 9 wirenboard-AMAZGWK5 ttymxc0 wirenboard-AMAZGWK5 login: