=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.09.06 16:11:18 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x010f010f .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3d3f .p0_mpwrdlctl= 0x3f3f3a38 .p0_mpwldectrl0= 0x00050005 .p0_mpwldectrl1= 0x00060006 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 26C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3 2 1 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot switch to partitions #0, OK mmc0(part 0) is current device SD/MMC found on device 0 324 bytes read in 68 ms (3.9 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 5899176 bytes read in 395 ms (14.2 MiB/s) MMC read: dev # 0, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard690 47008 bytes read in 117 ms (391.6 KiB/s) 485 bytes read in 151 ms (2.9 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 145 ms (3.9 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 173 ms (2 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 111 ms (2.9 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 125 ms (2 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef4c000, end 9ef6efff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb111 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 6.3.0-18) 6.3.0 20170516, GNU ld (GNU Binutils for Debian) 2.28) #1 Wed Apr 20 13:39:52 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.9.0 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9f000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 489384K/524288K available (8192K kernel code, 714K rwdata, 2680K rodata, 1024K init, 272K bss, 18520K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x238/0x3d4 with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000059] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002853] Console: colour dummy device 80x30 [ 0.002916] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002954] pid_max: default: 32768 minimum: 301 [ 0.003380] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003416] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.005006] CPU: Testing write buffer coherency: ok [ 0.006106] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.006991] devtmpfs: initialized [ 0.025208] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.025733] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025783] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.027144] pinctrl core: initialized pinctrl subsystem [ 0.029189] NET: Registered protocol family 16 [ 0.031512] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033568] thermal_sys: Registered thermal governor 'step_wise' [ 0.033856] cpuidle: using governor menu [ 0.233793] vdd1p1: supplied by regulator-dummy [ 0.246669] vdd3p0: supplied by regulator-dummy [ 0.259514] cpu: supplied by regulator-dummy [ 0.272448] vddsoc: supplied by regulator-dummy [ 0.635774] No ATAGs? [ 0.635837] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.635861] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.636478] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.637129] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.638562] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.638603] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.679672] mxs-dma 1804000.dma-apbh: initialized [ 0.685071] SCSI subsystem initialized [ 0.685583] usbcore: registered new interface driver usbfs [ 0.685713] usbcore: registered new interface driver hub [ 0.685825] usbcore: registered new device driver usb [ 0.686658] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.686811] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.688150] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.689068] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.689201] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.689815] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.690519] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.690649] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.691263] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.692832] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.693197] i2c i2c-1: IMX I2C adapter registered [ 0.694042] mc: Linux media interface: v0.10 [ 0.694165] videodev: Linux video capture interface: v2.00 [ 0.694347] pps_core: LinuxPPS API ver. 1 registered [ 0.694370] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.694432] PTP clock support registered [ 0.695066] Advanced Linux Sound Architecture Driver Initialized. [ 0.697199] clocksource: Switched to clocksource mxc_timer1 [ 0.715220] NET: Registered protocol family 2 [ 0.716419] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.716535] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.716651] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.716759] TCP: Hash tables configured (established 4096 bind 4096) [ 0.716955] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.717008] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.717509] NET: Registered protocol family 1 [ 0.718451] RPC: Registered named UNIX socket transport module. [ 0.718487] RPC: Registered udp transport module. [ 0.718505] RPC: Registered tcp transport module. [ 0.718522] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.719723] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.722596] Initialise system trusted keyrings [ 0.723043] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.734861] NFS: Registering the id_resolver key type [ 0.734947] Key type id_resolver registered [ 0.734970] Key type id_legacy registered [ 0.735884] Key type asymmetric registered [ 0.735922] Asymmetric key parser 'x509' registered [ 0.736024] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.736048] io scheduler mq-deadline registered [ 0.736069] io scheduler kyber registered [ 0.748357] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.748407] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.752389] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX [ 1.415317] printk: console [ttymxc0] enabled [ 1.421829] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX [ 1.465675] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.473114] random: fast init done [ 1.477061] random: crng init done [ 1.516664] brd: module loaded [ 1.534576] loop: module loaded [ 1.538200] at24 5-0050: supply vcc not found, using dummy regulator [ 1.549653] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.556618] at24 6-0050: supply vcc not found, using dummy regulator [ 1.568047] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.580531] libphy: Fixed MDIO Bus: probed [ 1.697885] pps pps0: new PPS source ptp0 [ 1.704304] libphy: fec_enet_mii_bus: probed [ 1.713130] fec 20b4000.ethernet eth0: registered PHC device 0 [ 1.837913] pps pps1: new PPS source ptp1 [ 1.878556] libphy: fec_enet_mii_bus: probed [ 1.883866] fec 2188000.ethernet eth1: registered PHC device 1 [ 1.890712] PPP generic driver version 2.4.2 [ 1.895435] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.902083] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.907856] usbcore: registered new interface driver usb-storage [ 1.914115] usbcore: registered new interface driver usbserial_generic [ 1.920797] usbserial: USB Serial support registered for generic [ 1.970266] rtc rtc0: invalid alarm value: 2022-09-06T38:25:00 [ 1.976544] rtc-pcf8563 4-0051: registered as rtc0 [ 1.993375] rtc-pcf8563 4-0051: setting system clock to 2022-09-06T13:11:09 UTC (1662469869) [ 2.012115] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1 [ 2.018659] i2c /dev entries driver [ 2.025499] lm75 4-0048: supply vs not found, using dummy regulator [ 2.037161] lm75 4-0048: hwmon0: sensor 'lm75b' [ 2.157681] sdhci: Secure Digital Host Controller Interface driver [ 2.163893] sdhci: Copyright(c) Pierre Ossman [ 2.168314] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.182136] ledtrig-cpu: registered to indicate activity on CPUs [ 2.190033] usbcore: registered new interface driver usbhid [ 2.195635] usbhid: USB HID core driver [ 2.212158] NET: Registered protocol family 10 [ 2.216747] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA [ 2.226695] Segment Routing with IPv6 [ 2.231219] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.239236] NET: Registered protocol family 17 [ 2.244001] Key type dns_resolver registered [ 2.252816] registered taskstats version 1 [ 2.256999] Loading compiled-in X.509 certificates [ 2.279269] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.291166] of_cfs_init [ 2.293916] of_cfs_init: OK [ 2.301746] ALSA device list: [ 2.304748] No soundcards found. [ 2.308538] Waiting for root device /dev/mmcblk0p2... [ 2.318237] mmc0: new DDR MMC card at address 0001 [ 2.323927] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.328966] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 2.335262] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 2.341628] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (245:0) [ 2.352092] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 2.374072] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem [ 2.381485] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 2.646488] EXT4-fs (mmcblk0p2): recovery complete [ 2.654452] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.662853] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.672011] devtmpfs: mounted [ 2.676340] Freeing unused kernel memory: 1024K [ 2.681208] Run /sbin/init as init process [ 3.014490] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 3.033538] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 3.078234] systemd[1]: Set hostname to . [ 3.689693] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 3.728811] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 3.768951] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 3.800377] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 3.840456] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 3.888965] systemd[1]: Starting File System Check on Root Device... Starting File System Check on Root Device... [ 3.906284] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. Starting Create list of required stce nodes for the current kernel... [ OK ] Started Forward Password Requests to Wall Directory Watch. Starting Load Kernel Modules... Mounting POSIX Message Queue File System... [ OK ] Reached target Remote File Systems. [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Syslog Socket. Mounting Debug File System... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Reached target Slices. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on udev Control Socket. Mounting /sys/kernel/config... Starting Journal Service... [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted /sys/kernel/config. [ OK ] Started File System Check on Root Device. [ OK ] Started Create list of required stavice nodes for the current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Started Journal Service. [ OK ] Started File System Check Daemon to report status. Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev... Starting Remount Root and Kernel File Systems... [ OK ] Started Apply Kernel Variables. [ OK ] Started Creat[ 4.992245] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro e Static Device Nodes in /dev. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting prepare partitions at first boot... Starting udev Coldplug all Devices... Starting udev Kernel Device Manager... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started prepare partitions at first boot. [ OK ] Reached target Local File Systems (Pre). [ 7.011911] Driver for 1-wire Dallas network protocol. [ OK ] Started udev Coldplug all Devices. [ 7.078611] gpio-68 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 7.150863] gpio-11 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ OK ] Found device /dev/ttymxc0. [ 7.469414] fec 20b4000.ethernet rename2: renamed from eth0 [ 7.836483] imx_usb 2184000.usb: No over current polarity defined [ 7.938613] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 7.985343] fec 2188000.ethernet eth0: renamed from eth1 [ 7.993756] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 8.047335] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 8.059508] fec 20b4000.ethernet eth1: renamed from rename2 [ 8.073502] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 8.081878] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.089156] usb usb1: Product: EHCI Host Controller [ 8.094057] usb usb1: Manufacturer: Linux 5.10.35-wb111 ehci_hcd [ 8.100093] usb usb1: SerialNumber: ci_hdrc.0 [ 8.391627] hub 1-0:1.0: USB hub found [ 8.426803] hub 1-0:1.0: 1 port detected [ 8.507450] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 8.592324] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 8.697359] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 8.724515] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 8.732877] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.740149] usb usb2: Product: EHCI Host Controller [ 8.745035] usb usb2: Manufacturer: Linux 5.10.35-wb111 ehci_hcd [ 8.751072] usb usb2: SerialNumber: ci_hdrc.1 [ 8.827419] usb usb1-port1: over-current condition [ 8.987599] hub 2-0:1.0: USB hub found [ 9.027303] hub 2-0:1.0: 1 port detected [ OK ] Found device /dev/mmcblk0p5. [ 9.447340] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ OK ] Found device /dev/mmcblk0p6. [ 9.678003] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 9.686231] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 9.807543] hub 2-1:1.0: USB hub found [ 9.831067] hub 2-1:1.0: 4 ports detected Starting File System Check on /dev/mmcblk0p6... Activating swap /dev/mmcblk0p5... [ 10.182668] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SS [ 10.198516] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ OK ] Activated swap /dev/mmcblk0p5. [ OK ] Reached target Swap. [ 10.362331] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00 [ 10.370793] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.378185] usb 2-1.1: Product: 802.11n WLAN Adapter [ 10.383166] usb 2-1.1: Manufacturer: Realtek [ 10.387477] usb 2-1.1: SerialNumber: 00e04c000001 [ OK ] Started File System Check on /dev/mmcblk0p6. Mounting /mnt/data... [ 10.666235] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 10.683373] Bluetooth: Core ver 2.22 [ 10.687116] NET: Registered protocol family 31 [ 10.691651] Bluetooth: HCI device and connection manager initialized [ OK ] Listening on Load/Save RF Kill Switch Status[ 10.706466] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) /dev/rfkill Watch. [ 10.735200] Bluetooth: HCI socket layer initialized [ OK ] Mounted /mnt/[ 10.777797] Bluetooth: L2CAP socket layer initialized data. [ 10.797403] Bluetooth: SCO socket layer initialized Mounting /var/log... [ 10.854535] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 10.886677] usbcore: registered new interface driver btusb Starting Load/Save RF Ki[ 10.899612] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 ll Switch Status... [ 10.911622] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 10.917847] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ 10.928968] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 10.935465] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2 [ 10.944784] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 [ 10.953864] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 11.036666] cfg80211: failed to load regulatory.db [ OK ] Mounted /var/log. [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Reached target Local File Systems. [ OK ] Started ifup for eth0. Starting Raise network interfaces... [ OK ] Started ifup for eth1. Starting prepare mounts and symlinks to config files... Starting Flush Journal to Persistent Storage... [ 11.725823] systemd-journald[111]: Received request to flush runtime journal from PID 1 [ 11.765623] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 [ 11.782666] systemd-journald[111]: File /var/log/journal/84ebb9a9047d51bdaa4e7ff362c682db/system.journal corrupted or uncleanly shut down, renaming and replacing. [ 11.851986] RTL871X: module init start [ 11.855884] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40 [ 11.862931] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ 12.204935] RTL871X: rtw_ndev_init(wlan0) [ 12.236948] RTL871X: rtw_ndev_init(wlan1) [ 12.285592] usbcore: registered new interface driver rtl8723bu [ 12.291521] RTL871X: module init ret=0 [ OK ] Started Flush Journal to Persistent Storage. [ 12.502026] usbcore: registered new interface driver rtl8xxxu [ OK ] Found device 802.11n_WLAN_Adapter. [ OK ] Started Raise network interfaces. [ OK ] Started ifup for wlan0. [ OK ] Started prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on KNX Daemon (socket). [ OK ] Started Monitor directories with device templates for wb-mqtt-serial. [ OK ] Reached target Paths. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Restore local date from Wiren Board GSM RTC... [ OK ] Started Regular background program processing daemon. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Started Generates wb-mqtt-serial UI schema for wb-mqtt-confed. Starting Restore /etc/resolv.conf ifore the ppp link was shut down... Starting initialize filesystems at first boot... Starting Login Service... Starting System Logging Service... [ OK ] Started Daily apt download activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started D-Bus System Message Bus. [ 15.671207] RTL871X: RTW_ADAPTIVITY_EN_ [ 15.671231] AUTO, chplan:0x20, Regulation:3,3 [ 15.679557] RTL871X: RTW_ADAPTIVITY_MODE_ [ 15.679562] NORMAL [ OK ] Started Cgroup management daemon. Starting Bluetooth service... [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started watch config files. [ 16.456569] new mount options do not match the existing superblock, will be ignored Starting Initialize Wiren Board Device Tree overlays... [ OK ] Started System Logging Service. [ OK ] Started Restore /etc/resolv.conf ifbefore the ppp link was shut down. [ 17.003417] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.008834] Bluetooth: BNEP filters: protocol multicast [ 17.134996] Bluetooth: BNEP socket layer initialized [ OK ] Started initialize filesystems at first boot. [ OK ] Started Bluetooth service. [ OK ] Started Login Service. Starting Hostname Service... [ OK ] Reached target Bluetooth. [ OK ] Reached target Network. Starting A high performance web server and a reverse proxy server... Starting dnsmasq - A lightweight DHCP and caching DNS server... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... Starting Avahi mDNS/DNS-SD Stack... Starting KNX Daemon... [ OK ] Started Permit User Sessions. [ OK ] Started Mosquitto MQTT v3.1/v3.1.1 Broker. [ OK ] Started KNX Daemon. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Hostname Service. [ OK ] Started OpenBSD Secure Shell server. [ 20.888487] RTL871X: nolinked power save enter [ OK ] Reached target Network is Online. Starting Daily apt download activities... Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Brings up/down network automatically... Starting LSB: Start NTP daemon... Starting Wiren Board MQTT to Modbus TCP gateway... [ OK ] Started Wiren Board journald to MQTT gateway. [ OK ] Started Wiren Board configuration editor backend. [ OK ] Started Wiren Board firmware update service. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc0. [ OK ] Reached target Login Prompts. [ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server. [ OK ] Started Wiren Board MQTT to OPC UA gateway. [ 25.225637] process '/sbin/netplugd' started with executable stack [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started LSB: Start NTP daemon. Starting Compensation of systime inevice-tree (with opposite sign)... [ OK ] Started A high performance web server and a reverse proxy server. Starting Initialize Wiren Board on successful boot... [ OK ] Started Compensation of systime in device-tree (with opposite sign). [ 27.988008] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 224, base_baud = 5000000) is a IMX Debian GNU/Linux 9 wirenboard-AU34OFFG ttymxc0 wirenboard-AU34OFFG login: [ 28.503209] RTL871X: RTW_ADAPTIVITY_EN_ [ 28.503233] AUTO, chplan:0x20, Regulation:3,3 [ 28.511513] RTL871X: RTW_ADAPTIVITY_MODE_ [ 28.511517] NORMAL [ 30.936668] RTL871X: nolinked power save leave [ 31.297465] SMSC LAN8710/LAN8720 20b4000.ethernet-1:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:00, irq=POLL) [ 31.533906] 2288000.serial: ttymxc7 at MMIO 0x2288000 (irq = 225, base_baud = 5000000) is a IMX [ 31.857134] RTL871X: assoc success [ 31.860762] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 32.010288] SMSC LAN8710/LAN8720 20b4000.ethernet-1:01: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) [ 33.447677] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 33.563315] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x0112010f .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3d40 .p0_mpwrdlctl= 0x3f3f3b39 .p0_mpwldectrl0= 0x00070005 .p0_mpwldectrl1= 0x00080008 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 38C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3 2 1 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra USB 3.0 Type: Removable Hard Disk Capacity: 14664.0 MB = 14.3 GB (30031872 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) Skip 7928976 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8200042c) Skip 46505 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82000e74) Skip 4917 bytes of data Skip 173102204 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820006a8) ** wb6_update_FACTORYRESET.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) reading wb6_update_FACTORYRESET.fit 7945616 bytes read in 4695 ms (1.6 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x82000300 Data Size: 7928976 Bytes = 7.6 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 47f6419e0d5d8326c41b16761827dc3d746fec78 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x83000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x83000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (830020c8) Skip 7928976 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8300042c) reading wb6_update_FACTORYRESET.fit 63589 bytes read in 499 ms (124 KiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x83000440 Data Size: 46505 Bytes = 45.4 KiB Architecture: ARM Hash algo: sha1 Hash value: ef9dd3fe2b348fb8eb9f150b9dc2e27d6899e823 ## Verifying ... sha1+ Loading part 0 ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef61000, end 9ef6f5a8 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.22-wb6_initramfs (root@WB-buildserver) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #2 SMP Tue Feb 1 16:52:01 MSK 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Wiren Board init (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 14 pages/cpu @cfbcf000 s25932 r8192 d23220 u57344 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=usbupdate,wb6_update_FACTORYRESET.fit [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506756K/524288K available (5120K kernel code, 202K rwdata, 1576K rodata, 5120K init, 295K bss, 17532K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xb0000000 - 0xd0000000 ( 512 MB) [ 0.000000] modules : 0xaf000000 - 0xb0000000 ( 16 MB) [ 0.000000] .text : 0xb0008000 - 0xb0600000 (6112 kB) [ 0.000000] .init : 0xb0800000 - 0xb0d00000 (5120 kB) [ 0.000000] .data : 0xb0d00000 - 0xb0d32880 ( 203 kB) [ 0.000000] .bss : 0xb0d34000 - 0xb0d7ddb0 ( 296 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000053] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002601] Console: colour dummy device 80x30 [ 0.002644] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002676] pid_max: default: 32768 minimum: 301 [ 0.002862] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002887] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.004083] CPU: Testing write buffer coherency: ok [ 0.004578] /cpus/cpu@0 missing clock-frequency property [ 0.004617] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004674] Setting up static identity map for 0x80100000 - 0x80100070 [ 0.007051] Brought up 1 CPUs [ 0.007086] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.007104] CPU: All CPU(s) started in SVC mode. [ 0.008317] devtmpfs: initialized [ 0.034541] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.035228] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.035279] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.035458] pinctrl core: initialized pinctrl subsystem [ 0.037492] NET: Registered protocol family 16 [ 0.038012] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.040718] cpuidle: using governor menu [ 0.076068] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.076100] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.078295] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.118529] mxs-dma 1804000.dma-apbh: initialized [ 0.123030] SCSI subsystem initialized [ 0.123639] usbcore: registered new interface driver usbfs [ 0.123800] usbcore: registered new interface driver hub [ 0.124053] usbcore: registered new device driver usb [ 0.125673] i2c-gpio i2c_rtc: using pins 48 (SDA) and 49 (SCL) [ 0.126530] i2c-gpio i2c_eeprom1: using pins 76 (SDA) and 67 (SCL) [ 0.127389] i2c-gpio i2c_eeprom2: using pins 70 (SDA) and 71 (SCL) [ 0.128887] i2c i2c-1: IMX I2C adapter registered [ 0.128928] i2c i2c-1: can't use DMA, using PIO instead. [ 0.129339] pps_core: LinuxPPS API ver. 1 registered [ 0.129362] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.129416] PTP clock support registered [ 0.131802] clocksource: Switched to clocksource mxc_timer1 [ 0.155690] NET: Registered protocol family 2 [ 0.156927] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.157052] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.157207] TCP: Hash tables configured (established 4096 bind 4096) [ 0.157322] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.157378] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.157684] NET: Registered protocol family 1 [ 0.158537] RPC: Registered named UNIX socket transport module. [ 0.158569] RPC: Registered udp transport module. [ 0.158587] RPC: Registered tcp transport module. [ 0.158602] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.727654] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.742932] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.744942] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.755370] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.755404] io scheduler noop registered (default) [ 0.760543] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.760587] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.769654] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX [ 1.323801] console [ttymxc0] enabled [ 1.329328] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 55, base_baud = 5000000) is a IMX [ 1.339612] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 56, base_baud = 5000000) is a IMX [ 1.382397] imx_rngc 2284000.rngb: Freescale RNGC registered. [ 1.417224] brd: module loaded [ 1.436212] loop: module loaded [ 1.444493] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.455940] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.463522] libphy: Fixed MDIO Bus: probed [ 1.469943] 20b4000.ethernet supply phy not found, using dummy regulator [ 1.477962] pps pps0: new PPS source ptp0 [ 1.510797] libphy: fec_enet_mii_bus: probed [ 1.517050] fec 20b4000.ethernet eth0: registered PHC device 0 [ 1.641890] 2188000.ethernet supply phy not found, using dummy regulator [ 1.762853] pps pps1: new PPS source ptp1 [ 1.767912] libphy: fec_enet_mii_bus: probed [ 1.775017] fec 2188000.ethernet eth1: registered PHC device 1 [ 1.781426] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.788129] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.793954] usbcore: registered new interface driver cdc_acm [ 1.799647] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.808006] usbcore: registered new interface driver usb-storage [ 1.858859] rtc rtc0: invalid alarm value: 2022-9-6 38:25:0 [ 1.865071] rtc-pcf8563 4-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 1.881133] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1 [ 1.890360] i2c /dev entries driver [ 1.898536] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 1.906027] imx6ul-pinctrl 20e0000.iomuxc: pin MX6UL_PAD_SD1_DATA1 already requested by watchdog; cannot claim for watchdog_6x [ 1.917581] imx6ul-pinctrl 20e0000.iomuxc: pin-114 (watchdog_6x) status -22 [ 1.924635] imx6ul-pinctrl 20e0000.iomuxc: could not request pin 114 (MX6UL_PAD_SD1_DATA1) from group wdggrp_6x on device 20e0000.iomuxc [ 1.937055] gpio-wdt watchdog_6x: Error applying setting, reverse things back [ 1.944286] gpio-wdt: probe of watchdog_6x failed with error -22 [ 1.952150] sdhci: Secure Digital Host Controller Interface driver [ 1.958375] sdhci: Copyright(c) Pierre Ossman [ 1.962835] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.031872] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 2.051444] ledtrig-cpu: registered to indicate activity on CPUs [ 2.063535] random: fast init done [ 2.079451] usbcore: registered new interface driver usbhid [ 2.087218] usbhid: USB HID core driver [ 2.101588] NET: Registered protocol family 17 [ 2.112601] Registering SWP/SWPB emulation handler [ 2.119634] registered taskstats version 1 [ 2.136664] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.160033] rtc-pcf8563 4-0051: setting system clock to 2022-09-06 13:14:42 UTC (1662470082) [ 2.168525] of_cfs_init [ 2.172160] of_cfs_init: OK [ 2.182105] vdd3p0: disabling [ 2.185126] vref-3v3: disabling [ 2.188278] usb1_vbus: disabling [ 2.202318] Freeing unused kernel memory: 5120K (b0800000 - b0d00000) [ 2.217806] mmc0: new DDR MMC card at address 0001 [ 2.237890] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.252166] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB mount: mounting none on /dev/pts [ 2.262127] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB failed: No such file or directory [ 2.282364] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB [ 2.293101] mmcblk0: p1 p2 p3 p4 < p5 p6 > Boot mode: usbupdate,wb6_update_FACTORYRESET.fit Board is WB6, loading ci_hdrc_imx module [ 2.530881] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 2.536123] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 2.571862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 2.577555] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.584413] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.591643] usb usb1: Product: EHCI Host Controller [ 2.596578] usb usb1: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd [ 2.603240] usb usb1: SerialNumber: ci_hdrc.0 [ 2.609072] hub 1-0:1.0: USB hub found [ 2.613076] hub 1-0:1.0: 1 port detected [ 2.618544] 2184200.usb supply vbus not found, using dummy regulator [ 2.629231] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.634328] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 2.661896] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.667676] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.674555] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.681838] usb usb2: Product: EHCI Host Controller [ 2.686734] usb usb2: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd [ 2.693423] usb usb2: SerialNumber: ci_hdrc.1 [ 2.699199] hub 2-0:1.0: USB hub found [ 2.703183] hub 2-0:1.0: 1 port detected [ 3.061967] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 3.252829] usb 2-1: New USB device found, idVendor=0424, idProduct=2514 [ 3.259656] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.269976] hub 2-1:1.0: USB hub found [ 3.274181] hub 2-1:1.0: 4 ports detected [ 3.361988] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.554222] usb 1-1: New USB device found, idVendor=0781, idProduct=5591 [ 3.561052] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.568424] usb 1-1: Product: Ultra USB 3.0 [ 3.572747] usb 1-1: Manufacturer: SanDisk [ 3.576889] usb 1-1: SerialNumber: 4C530000090318211233 [ 3.585340] usb-storage 1-1:1.0: USB Mass Storage device detected [ 3.593540] scsi host0: usb-storage 1-1:1.0 [ 3.601921] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ 3.754673] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720 [ 3.761680] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.769285] usb 2-1.1: Product: 802.11n WLAN Adapter [ 3.774399] usb 2-1.1: Manufacturer: Realtek [ 3.778717] usb 2-1.1: SerialNumber: 00e04c000001 Load modules for USB to work Starting USB update Waiting for USB to settle (0/10) [ 4.644459] scsi 0:0:0:0: Direct-Access SanDisk Ultra USB 3.0 1.00 PQ: 0 ANSI: 6 [ 4.656901] sd 0:0:0:0: [sda] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB) [ 4.668865] sd 0:0:0:0: [sda] Write Protect is off [ 4.675618] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 4.699837] sda: sda1 [ 4.712505] sd 0:0:0:0: [sda] Attached SCSI removable disk umount: can't umount /usb: Invalid argument Looking for wb6_update_FACTORYRESET.fit on /dev/sda umount: can't umount /usb: Invalid argument mount: mounting /dev/sda on /usb failed: Invalid argument Looking for wb6_update_FACTORYRESET.fit on /dev/sda1 umount: can't umount /usb: Invalid argument [ 5.085824] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. BusyBox v1.22.1 (Debian 1:1.22.0-19+deb9u2) built-in shell (ash) Enter 'help' for a list of built-in commands. ~ # ############################################################################## FACTORY RESET REQUESTED This WILL destroy ALL YOUR DATA: configuration, scripts, files in home directory! If you are ABSOLUTELY SURE that you want to reset Wiren Board to factory condition, hold the FW button for 4 seconds. If you will not do it in 10 seconds, the controller will reboot without firmware update. If you want to perform a regular firmware update, rename FIT file to "wbX_update.fit" without "factory-reset" suffix. ############################################################################## .... Factory reset is confirmed! =============================================================================== Tue Sep 6 13:14:51 UTC 2022: started update from /usb/wb6_update_FACTORYRESET.fit =============================================================================== Description: WirenBoard firmware update Compatible device: contactless,imx6ul-wirenboard670 Firmware version: 202208261140 Firmware compatible: unknown Release name: wb-2204 Release suite: stable Release target: wb6/stretch Release repo prefix: Time of creation: Fri Aug 26 11:41:50 UTC 2022 =============================================================================== >>> Checking SHA1 hash of install PROGRESS: 0% PROGRESS: 0% >>> SHA1 hash of install ok >>> Wiping data partition (factory reset) mke2fs 1.43.4 (31-Jan-2017) ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/mmcblk0p6 is mounted. Discarding device blocks: 4096/1264896[ 12.682232] random: crng init done 528384/12648961052672/1264896 done Creating filesystem with 1264896 4k blocks and 316368 inodes Filesystem UUID: 42310dd1-d26b-4580-8d07-d451bd73756f Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Allocating group tables: 0/39 done Writing inode tables: 0/39 done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: 0/39 done >>> Extracting install script >>> Running install script >>> Checking SHA1 hash of rootfs PROGRESS: 0% PROGRESS: 4% PROGRESS: 8% PROGRESS: 12% PROGRESS: 17% PROGRESS: 21% PROGRESS: 25% PROGRESS: 30% PROGRESS: 34% PROGRESS: 38% PROGRESS: 43% PROGRESS: 47% PROGRESS: 51% PROGRESS: 56% PROGRESS: 60% PROGRESS: 64% PROGRESS: 69% PROGRESS: 73% PROGRESS: 77% PROGRESS: 82% PROGRESS: 86% PROGRESS: 90% PROGRESS: 95% PROGRESS: 99% PROGRESS: 100% >>> SHA1 hash of rootfs ok >>> Installing firmware update >>> Getting mmcpart from U-Boot environment >>> Will install to /dev/mmcblk0p3 >>> Check if partition table is correct [ 52.572480] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) >>> Mounting /dev/mmcblk0p3 at /dev/shm/rootfs [ 52.605065] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) >>> Cleaning up /dev/mmcblk0p3 >>> Cleaning up using rsync >>> Extracting files to new rootfs /dev/shm/rootfs / PROGRESS: 0% PROGRESS: 2% PROGRESS: 4% PROGRESS: 5% PROGRESS: 7% PROGRESS: 9% PROGRESS: 10% PROGRESS: 12% PROGRESS: 14% PROGRESS: 16% PROGRESS: 18% PROGRESS: 19% PROGRESS: 20% PROGRESS: 21% PROGRESS: 23% PROGRESS: 25% PROGRESS: 25% PROGRESS: 26% PROGRESS: 27% PROGRESS: 29% PROGRESS: 31% PROGRESS: 33% PROGRESS: 34% PROGRESS: 36% PROGRESS: 38% PROGRESS: 40% PROGRESS: 41% PROGRESS: 42% PROGRESS: 43% PROGRESS: 45% PROGRESS: 47% PROGRESS: 49% PROGRESS: 49% PROGRESS: 50% PROGRESS: 50% PROGRESS: 51% PROGRESS: 52% PROGRESS: 53% PROGRESS: 55% PROGRESS: 55% PROGRESS: 56% PROGRESS: 57% PROGRESS: 58% PROGRESS: 60% PROGRESS: 61% PROGRESS: 62% PROGRESS: 63% PROGRESS: 64% PROGRESS: 65% PROGRESS: 67% PROGRESS: 68% PROGRESS: 70% PROGRESS: 72% PROGRESS: 74% PROGRESS: 75% PROGRESS: 77% PROGRESS: 79% PROGRESS: 81% PROGRESS: 83% PROGRESS: 85% PROGRESS: 86% PROGRESS: 87% PROGRESS: 88% PROGRESS: 89% PROGRESS: 90% PROGRESS: 92% PROGRESS: 93% PROGRESS: 93% PROGRESS: 94% PROGRESS: 96% PROGRESS: 97% PROGRESS: 98% PROGRESS: 99% PROGRESS: 100% / >>> Recovering device certificates [ 125.498061] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities [ 125.563021] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities [ 125.626844] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null) >>> Mount /dev, /proc and /sys to rootfs >>> Running post-install scripts >>> > Processing /dev/shm/rootfs/usr/lib/wb-image-update/postinst/10update-u-boot Trying to install u-boot using u-boot-install-wb from new rootfs Das U-Boot installator for Wiren Board You are about to install U-boot image '/usr/lib/u-boot/mx6ul_wirenboard6/u-boot-with-spl.imx' on '/dev/mmcblk0' (platform wb6) Force installation requested Writing U-boot image '/usr/lib/u-boot/mx6ul_wirenboard6/u-boot-with-spl.imx' on '/dev/mmcblk0' (options 'bs=512 seek=2') 769+1 records in 769+1 records out 394124 bytes (394 kB, 385 KiB) copied, 0.35434 s, 1.1 MB/s Syncing device >>> Unmounting /dev, /proc and /sys from rootfs >>> Unmounting new rootfs >>> Switching to new rootfs >>> Done! >>> Reboot system [ 131.346049] ci_hdrc ci_hdrc.1: remove, state 1 [ 131.350543] usb usb2: USB disconnect, device number 1 [ 131.355933] usb 2-1: USB disconnect, device number 2 [ 131.360915] usb 2-1.1: USB disconnect, device number 3 [ 131.371964] ci_hdrc ci_hdrc.1: USB bus 2 deregistered [ 131.377365] ci_hdrc ci_hdrc.0: remove, state 1 [ 131.381992] usb usb1: USB disconnect, device number 1 [ 131.387059] usb 1-1: USB disconnect, device number 2 [ 131.513873] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 131.540390] reboot: Restarting system U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x010f010f .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3c40 .p0_mpwrdlctl= 0x3f3f3b38 .p0_mpwldectrl0= 0x00070004 .p0_mpwldectrl1= 0x00080008 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 46C Reset cause: WDOG Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 3 2 1 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra USB 3.0 Type: Removable Hard Disk Capacity: 14664.0 MB = 14.3 GB (30031872 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## No USB update detected, continuing boot switch to partitions #0, OK mmc0(part 0) is current device SD/MMC found on device 0 324 bytes read in 68 ms (3.9 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 5899176 bytes read in 395 ms (14.2 MiB/s) MMC read: dev # 0, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard690 47008 bytes read in 117 ms (391.6 KiB/s) 485 bytes read in 151 ms (2.9 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 144 ms (3.9 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 173 ms (2 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 111 ms (2.9 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 125 ms (2 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef4c000, end 9ef6efff ... OK Starting kernel ... U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x0112010f .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3d40 .p0_mpwrdlctl= 0x3f3f3b38 .p0_mpwldectrl0= 0x00070005 .p0_mpwldectrl1= 0x00080008 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3 2 1 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra USB 3.0 Type: Removable Hard Disk Capacity: 14664.0 MB = 14.3 GB (30031872 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x0112010f .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3e41 .p0_mpwrdlctl= 0x3f3f3b38 .p0_mpwldectrl0= 0x00070003 .p0_mpwldectrl1= 0x00080008 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 42C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3 2 1 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot switch to partitions #0, OK mmc0(part 0) is current device SD/MMC found on device 0 324 bytes read in 67 ms (3.9 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 5899176 bytes read in 395 ms (14.2 MiB/s) MMC read: dev # 0, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard690 47008 bytes read in 117 ms (391.6 KiB/s) 485 bytes read in 151 ms (2.9 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 144 ms (3.9 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 172 ms (2 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 112 ms (2 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 124 ms (2 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef4c000, end 9ef6efff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb111 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 6.3.0-18) 6.3.0 20170516, GNU ld (GNU Binutils for Debian) 2.28) #1 Wed Apr 20 13:39:52 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.9.0 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9f000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait ro [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 489384K/524288K available (8192K kernel code, 714K rwdata, 2680K rodata, 1024K init, 272K bss, 18520K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x238/0x3d4 with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000063] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002848] Console: colour dummy device 80x30 [ 0.002915] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002958] pid_max: default: 32768 minimum: 301 [ 0.003384] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003419] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.005021] CPU: Testing write buffer coherency: ok [ 0.006118] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.007005] devtmpfs: initialized [ 0.025195] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.025719] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025767] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.027127] pinctrl core: initialized pinctrl subsystem [ 0.029196] NET: Registered protocol family 16 [ 0.031527] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033573] thermal_sys: Registered thermal governor 'step_wise' [ 0.033864] cpuidle: using governor menu [ 0.233725] vdd1p1: supplied by regulator-dummy [ 0.246587] vdd3p0: supplied by regulator-dummy [ 0.259438] cpu: supplied by regulator-dummy [ 0.272382] vddsoc: supplied by regulator-dummy [ 0.635774] No ATAGs? [ 0.635836] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.635859] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.636474] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.637121] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.638560] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.638597] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.679504] mxs-dma 1804000.dma-apbh: initialized [ 0.684910] SCSI subsystem initialized [ 0.685434] usbcore: registered new interface driver usbfs [ 0.685565] usbcore: registered new interface driver hub [ 0.685681] usbcore: registered new device driver usb [ 0.686511] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.686662] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.687997] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.688911] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.689041] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.689653] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.690349] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.690482] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.691092] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.692663] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.693025] i2c i2c-1: IMX I2C adapter registered [ 0.693866] mc: Linux media interface: v0.10 [ 0.693991] videodev: Linux video capture interface: v2.00 [ 0.694182] pps_core: LinuxPPS API ver. 1 registered [ 0.694208] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.694269] PTP clock support registered [ 0.694917] Advanced Linux Sound Architecture Driver Initialized. [ 0.697037] clocksource: Switched to clocksource mxc_timer1 [ 0.715027] NET: Registered protocol family 2 [ 0.716219] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.716334] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.716452] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.716560] TCP: Hash tables configured (established 4096 bind 4096) [ 0.716764] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.716817] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.717325] NET: Registered protocol family 1 [ 0.718266] RPC: Registered named UNIX socket transport module. [ 0.718301] RPC: Registered udp transport module. [ 0.718321] RPC: Registered tcp transport module. [ 0.718337] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.719529] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.722418] Initialise system trusted keyrings [ 0.722866] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.734699] NFS: Registering the id_resolver key type [ 0.734778] Key type id_resolver registered [ 0.734800] Key type id_legacy registered [ 0.735699] Key type asymmetric registered [ 0.735739] Asymmetric key parser 'x509' registered [ 0.735845] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.735871] io scheduler mq-deadline registered [ 0.735892] io scheduler kyber registered [ 0.748160] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.748211] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.752194] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX [ 1.415087] printk: console [ttymxc0] enabled [ 1.421600] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX [ 1.465438] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.472877] random: fast init done [ 1.476821] random: crng init done [ 1.516417] brd: module loaded [ 1.534321] loop: module loaded [ 1.537939] at24 5-0050: supply vcc not found, using dummy regulator [ 1.549387] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.556360] at24 6-0050: supply vcc not found, using dummy regulator [ 1.567831] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.580317] libphy: Fixed MDIO Bus: probed [ 1.697719] pps pps0: new PPS source ptp0 [ 1.704138] libphy: fec_enet_mii_bus: probed [ 1.712964] fec 20b4000.ethernet eth0: registered PHC device 0 [ 1.837737] pps pps1: new PPS source ptp1 [ 1.878520] libphy: fec_enet_mii_bus: probed [ 1.883824] fec 2188000.ethernet eth1: registered PHC device 1 [ 1.890686] PPP generic driver version 2.4.2 [ 1.895414] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.902062] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.907829] usbcore: registered new interface driver usb-storage [ 1.914088] usbcore: registered new interface driver usbserial_generic [ 1.920772] usbserial: USB Serial support registered for generic [ 1.970211] rtc rtc0: invalid alarm value: 2022-09-06T38:25:00 [ 1.976488] rtc-pcf8563 4-0051: registered as rtc0 [ 1.993322] rtc-pcf8563 4-0051: setting system clock to 2022-09-06T13:17:51 UTC (1662470271) [ 2.011994] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1 [ 2.018531] i2c /dev entries driver [ 2.025339] lm75 4-0048: supply vs not found, using dummy regulator [ 2.037000] lm75 4-0048: hwmon0: sensor 'lm75b' [ 2.157530] sdhci: Secure Digital Host Controller Interface driver [ 2.163740] sdhci: Copyright(c) Pierre Ossman [ 2.168161] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.181985] ledtrig-cpu: registered to indicate activity on CPUs [ 2.189866] usbcore: registered new interface driver usbhid [ 2.195469] usbhid: USB HID core driver [ 2.211978] NET: Registered protocol family 10 [ 2.216566] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA [ 2.226499] Segment Routing with IPv6 [ 2.231030] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.239032] NET: Registered protocol family 17 [ 2.243805] Key type dns_resolver registered [ 2.252623] registered taskstats version 1 [ 2.256804] Loading compiled-in X.509 certificates [ 2.279133] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.291043] of_cfs_init [ 2.293795] of_cfs_init: OK [ 2.301642] ALSA device list: [ 2.304646] No soundcards found. [ 2.308444] Waiting for root device /dev/mmcblk0p3... [ 2.318122] mmc0: new DDR MMC card at address 0001 [ 2.323804] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.328846] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 2.335142] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 2.341506] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (245:0) [ 2.351883] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 2.375165] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 2.383695] VFS: Mounted root (ext4 filesystem) readonly on device 179:3. [ 2.395128] devtmpfs: mounted [ 2.402327] Freeing unused kernel memory: 1024K [ 2.407766] Run /sbin/init as init process [ 2.731626] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 2.750634] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 2.788108] systemd[1]: Set hostname to . [ 3.338903] systemd[1]: [/lib/systemd/system/wb-mqtt-w1.service:10] Unknown lvalue 'StartLimitIntervalSec' in section 'Service' [ 3.420597] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 3.470952] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 3.508220] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 3.539627] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 3.577748] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 3.620914] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. Starting Create list of required stce nodes for the current kernel... [ OK ] Created slice system-systemd\x2dfsck.slice. Mounting /sys/kernel/config... Mounting POSIX Message Queue File System... Starting Load Kernel Modules... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting Debug File System... [ OK ] Created slice system-getty.slice. Starting File System Check on Root Device... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Syslog Socket. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Listening on udev Kernel Socket. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted /sys/kernel/config. [ OK ] Started Journal Service. [ OK ] Started Create list of required stavice nodes for the current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Started File System Check on Root Device. [ OK ] Started File System Check Daemon to report status. Starting Remount Root and Kernel File Systems... Starting Apply Kernel Va[ 4.642068] EXT4-fs (mmcblk0p3): re-mounted. Opts: errors=remount-ro riables... Starting Create Static Device Nodes in /dev... [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Apply Kernel Variables. Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Starting prepare partitions at first boot... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. [ OK ] Started prepare partitions at first boot. [ OK ] Reached target Local File Systems (Pre). [ 6.785428] Driver for 1-wire Dallas network protocol. [ OK ] Started udev Coldplug all Devices. [ 6.861548] gpio-68 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 6.954102] gpio-11 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ OK ] Found device /dev/ttymxc0. [ 7.182852] fec 20b4000.ethernet rename2: renamed from eth0 [ 7.594934] imx_usb 2184000.usb: No over current polarity defined [ 7.684836] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 7.717234] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 7.780532] fec 2188000.ethernet eth0: renamed from eth1 [ 7.807178] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 7.842340] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 7.850720] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.857983] usb usb1: Product: EHCI Host Controller [ 7.862870] usb usb1: Manufacturer: Linux 5.10.35-wb111 ehci_hcd [ 7.868902] usb usb1: SerialNumber: ci_hdrc.0 [ 7.882048] fec 20b4000.ethernet eth1: renamed from rename2 [ 8.141263] hub 1-0:1.0: USB hub found [ 8.162591] hub 1-0:1.0: 1 port detected [ 8.203523] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 8.264325] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 8.397319] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 8.460009] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 8.468418] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.475650] usb usb2: Product: EHCI Host Controller [ 8.480576] usb usb2: Manufacturer: Linux 5.10.35-wb111 ehci_hcd [ 8.486590] usb usb2: SerialNumber: ci_hdrc.1 [ 8.517215] usb usb1-port1: over-current condition [ 8.730795] hub 2-0:1.0: USB hub found [ 8.777283] hub 2-0:1.0: 1 port detected [ OK ] Found device /dev/mmcblk0p6. [ 9.187178] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ OK ] Found device /dev/mmcblk0p5. [ 9.427869] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 9.436096] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 9.560371] hub 2-1:1.0: USB hub found [ 9.595161] hub 2-1:1.0: 4 ports detected Activating swap /dev/mmcblk0p5... [ 9.886691] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SS Starting File System Check on /dev/mmcblk0p6... [ 9.967155] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ OK ] Activated swap /dev/mmcblk0p5. [ OK ] Reached target Swap. [ OK ] Started File System Check on /dev/mmcblk0p6. Mounting /mnt/data...[ 10.128842] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00 [ 10.138910] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.146336] usb 2-1.1: Product: 802.11n WLAN Adapter [ 10.151339] usb 2-1.1: Manufacturer: Realtek [ 10.155615] usb 2-1.1: SerialNumber: 00e04c000001 [ 10.245914] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /mnt/data. Mounting /var/log... [ 10.426003] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 10.436462] Bluetooth: Core ver 2.22 [ 10.458380] NET: Registered protocol family 31 [ 10.462891] Bluetooth: HCI device and connection manager initialized [ 10.498664] Bluetooth: HCI socket layer initialized [ OK ] Mounted /var/log. [ 10.537968] Bluetooth: L2CAP socket layer initialized [ 10.543093] Bluetooth: SCO socket layer initialized Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems. [ 10.612531] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ OK ] Started ifup for eth1. [ 10.658433] usbcore: registered new interface driver btusb [ OK ] Started ifup for eth0. [ 10.678450] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [ 10.688471] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 10.694542] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ 10.702606] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 10.713476] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 10.720119] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2 [ 10.729369] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 [ 10.788121] cfg80211: failed to load regulatory.db Starting Raise network interfaces... Starting prepare mounts and symlinks to config files... [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ 11.072480] systemd-journald[110]: Received request to flush runtime journal from PID 1 Starting Load/Save RF Kill Switch Status... [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Started Flush Journal to Persistent Storage. [ 11.543469] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 [ 11.679322] RTL871X: module init start [ 11.683106] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40 [ 11.690195] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ 11.987752] RTL871X: rtw_ndev_init(wlan0) [ 12.012052] RTL871X: rtw_ndev_init(wlan1) [ 12.051152] usbcore: registered new interface driver rtl8723bu [ 12.057080] RTL871X: module init ret=0 [ 12.270015] usbcore: registered new interface driver rtl8xxxu [ OK ] Found device 802.11n_WLAN_Adapter. [ OK ] Started Raise network interfaces. [ OK ] Started ifup for wlan0. [ 15.289441] RTL871X: RTW_ADAPTIVITY_EN_ [ 15.289465] AUTO, chplan:0x20, Regulation:3,3 [ 15.297765] RTL871X: RTW_ADAPTIVITY_MODE_ [ 15.297769] NORMAL [ 19.209093] RTL871X: nolinked power save enter [ OK ] Started prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Monitor directories with device templates for wb-mqtt-serial. [ OK ] Reached target Paths. [ OK ] Listening on KNX Daemon (socket). [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily apt download activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting initialize filesystems at first boot... Starting Login Service... [ OK ] Started watch config files. [ OK ] Started Regular background program processing daemon. [ OK ] Started Cgroup management daemon. Starting Bluetooth service... [ OK ] Started Generates wb-mqtt-serial UI schema for wb-mqtt-confed. Starting Restore local date from Wiren Board GSM RTC... Starting System Logging Service... [ 20.580835] new mount options do not match the existing superblock, will be ignored Starting Mosquitto MQTT v3.1/v3.1.1 Broker... Starting Initialize Wiren Board Device Tree overlays... Starting Restore /etc/resolv.conf ifore the ppp link was shut down... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Bluetooth service. [ OK ] Reached target Bluetooth. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ 21.852573] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 21.858012] Bluetooth: BNEP filters: protocol multicast [ 21.894213] Bluetooth: BNEP socket layer initialized [ 21.957294] SMSC LAN8710/LAN8720 20b4000.ethernet-1:01: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) [ OK ] Started System Logging Service. [ OK ] Started Restore /etc/resolv.conf ifbefore the ppp link was shut down. [ OK ] Started Mosquitto MQTT v3.1/v3.1.1 Broker. [ OK ] Started Login Service. Starting Hostname Service... Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Started Wiren Board configuration editor backend. [ OK ] Started Wiren Board firmware update service. Starting Wiren Board MQTT to Modbus TCP gateway... [ 23.855704] EXT4-fs (mmcblk0p2): recovery complete [ 23.910223] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Started Wiren Board MQTT to OPC UA gateway. [ OK ] Started Hostname Service. [ OK ] Started Wiren Board MQTT to Modbus TCP gateway. [ 30.731254] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 224, base_baud = 5000000) is a IMX [ OK ] Started Initialize Wiren Board Device Tree overlays. [ OK ] Started one-click diagnostic data card, generating archive with data. [ OK ] Started metrics sender.. [ OK ] Started MQTT Rule engine for Wiren Board. Starting KNXD Configurator for Wiren Board... [ OK ] Started Restore local date from Wiren Board GSM RTC. [ 39.797406] SMSC LAN8710/LAN8720 20b4000.ethernet-1:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:00, irq=POLL) [ 42.007536] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 42.047201] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Starting KNX Daemon... [ OK ] Started KNX Daemon. [ OK ] Started Wiren Board MQTT KNX bridge. [ OK ] Started KNXD Configurator for Wiren Board. [ ***] A start job is running for initialiems at first boot (37s / no limit) [ **] A start job is running for initialiems at first boot (38s / no limit) [ *] A start job is running for initialiems at first boot (38s / no limit) [ **] A start job is running for initialiems at first boot (39s / no limit) [ ***] A start job is running for initialiems at first boot (39s / no limit) [ *** ] A start job is running for initialiems at first boot (40s / no limit) [ *** ] A start job is running for initialiems at first boot (40s / no limit) [*** ] A start job is running for initialiems at first boot (41s / no limit) [** ] A start job is running for initialiems at first boot (41s / no limit) [* ] A start job is running for initialiems at first boot (42s / no limit) [** ] A start job is running for initialiems at first boot (42s / no limit) [ OK ] Stopped KNX Daemon. [*** ] A start job is running for initialiems at first boot (48s / no limit) [ *** ] A start job is running for initialiems at first boot (48s / no limit) [ *** ] A start job is running for initialiems at first boot (49s / no limit) [ ***] A start job is running for initialiems at first boot (49s / no limit) [ **] A start job is running for initialiems at first boot (50s / no limit) [ *] A start job is running for initialiems at first boot (50s / no limit) [ **] A start job is running for initialiems at first boot (51s / no limit) [ ***] A start job is running for initialiems at first boot (51s / no limit) [ *** ] A start job is running for initialiems at first boot (52s / no limit) [ *** ] A start job is running for initialiems at first boot (52s / no limit) [*** ] A start job is running for initialiems at first boot (53s / no limit) [** ] A start job is running for initialiems at first boot (53s / no limit) [* ] A start job is running for initialiems at first boot (54s / no limit) [** ] A start job is running for initialiems at first boot (54s / no limit) [*** ] A start job is running for initialiems at first boot (55s / no limit) [ *** ] A start job is running for initialiems at first boot (55s / no limit) [ *** ] A start job is running for initialiems at first boot (56s / no limit) [ ***] A start job is running for initialiems at first boot (56s / no limit) [ **] A start job is running for initialiems at first boot (57s / no limit) [ *] A start job is running for initialiems at first boot (57s / no limit) [ **] A start job is running for initialiems at first boot (58s / no limit) [ ***] A start job is running for initialiems at first boot (58s / no limit) [ *** ] A start job is running for initialiems at first boot (59s / no limit) [ *** ] A start job is running for initialiems at first boot (59s / no limit) [*** ] A start job is running for initialims at first boot (1min / no limit) [** ] A start job is running for initialims at first boot (1min / no limit) [* ] A start job is running for initialiat first boot (1min 1s / no limit) [** ] A start job is running for initialiat first boot (1min 1s / no limit) [*** ] A start job is running for initialiat first boot (1min 2s / no limit) [ *** ] A start job is running for initialiat first boot (1min 2s / no limit) [ OK ] Started initialize filesystems at first boot. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Reached target Network. Starting A high performance web server and a reverse proxy server... Starting MQTT Driver for ADC... [ OK ] Started Wiren Board journald to MQTT gateway. Starting MQTT Driver for GPIO-controlled switches... Starting KNX Daemon... Starting dnsmasq - A lightweight DHCP and caching DNS server... Starting Permit User Sessions... [ OK ] Started MQTT Driver for serial devices. [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. [ OK ] Started Wiren Board database logger. Starting OpenBSD Secure Shell server... [ OK ] Started KNX Daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Network is Online. Starting LSB: Brings up/down network automatically... Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Start NTP daemon... [ OK ] Started OpenBSD Secure Shell server. [ 78.065115] process '/sbin/netplugd' started with executable stack [ OK ] Started LSB: Start NTP daemon. Starting Compensation of systime inevice-tree (with opposite sign)... [ OK ] Started Compensation of systime in device-tree (with opposite sign). [ 80.999816] RTL871X: RTW_ADAPTIVITY_EN_ [ 80.999841] AUTO, chplan:0x20, Regulation:3,3 [ 81.008124] RTL871X: RTW_ADAPTIVITY_MODE_ [ 81.008128] NORMAL Debian GNU/Linux 9 wirenboard-AU34OFFG ttymxc0 wirenboard-AU34OFFG login: [ 82.148595] RTL871X: nolinked power save leave [ 82.850854] RTL871X: assoc success [ 82.854403] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready