▒ U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010d0107 .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3d3c .p0_mpwrdlctl = 0x3f3f3733 .p0_mpwldectrl0 = 0x00090009 .p0_mpwldectrl1 = 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 31C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade Type: Removable Hard Disk Capacity: 29340.0 MB = 28.6 GB (60088320 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## No USB update detected, continuing boot MMC Device 1 not found no mmc device at slot 1 SD/MMC found on device 1 MMC Device 1 not found ** Bad device mmc 1 ** Running default loadzimage ... MMC Device 1 not found ** Bad device mmc 1 ** => U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x01060106 .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3b3c .p0_mpwrdlctl = 0x3f3f3633 .p0_mpwldectrl0 = 0x00090009 .p0_mpwldectrl1 = 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 32C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade Type: Removable Hard Disk Capacity: 29340.0 MB = 28.6 GB (60088320 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x820000c0 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82002088) Skip 7961328 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8200058c) Skip 44468 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820017cc) Skip 4085 bytes of data Skip 162454668 bytes of data reading wb6_update_FACTORYRESET.fit ** wb6_update_FACTORYRESET.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x820000c0 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82002088) reading wb6_update_FACTORYRESET.fit 7977904 bytes read in 4701 ms (1.6 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x820002c0 Data Size: 7961328 Bytes = 7.6 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 83e0ef509133764a09e3e5a3501c6082802add22 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x83000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x830000c0 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (83002088) Skip 7961328 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8300058c) reading wb6_update_FACTORYRESET.fit 61488 bytes read in 486 ms (123 KiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x830003c0 Data Size: 44468 Bytes = 43.4 KiB Architecture: ARM Hash algo: sha1 Hash value: f9d735f903dafa43fd9cb5fa9e2bc7909f33d69c ## Verifying ... sha1+ Loading part 0 ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef61000, end 9ef6edb3 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.22-wb6_initramfs (jenkins@WB-buildserver) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #2 SMP Fri Jan 4 00:39:16 MSK 2019 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Wiren Board rev. 6.1 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 14 pages/cpu @dfbd0000 s25932 r8192 d23220 u57344 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=usbupdate,wb6_update_FACTORYRESET.fit [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506736K/524288K available (5120K kernel code, 202K rwdata, 1580K rodata, 5120K init, 313K bss, 17552K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0600000 (6112 kB) [ 0.000000] .init : 0xc0800000 - 0xc0d00000 (5120 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0d32b80 ( 203 kB) [ 0.000000] .bss : 0xc0d34000 - 0xc0d82630 ( 314 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000015] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000054] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002512] Console: colour dummy device 80x30 [ 0.002553] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002584] pid_max: default: 32768 minimum: 301 [ 0.002778] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002804] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.004005] CPU: Testing write buffer coherency: ok [ 0.004507] /cpus/cpu@0 missing clock-frequency property [ 0.004546] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004598] Setting up static identity map for 0x80100000 - 0x80100070 [ 0.006948] Brought up 1 CPUs [ 0.006983] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.006999] CPU: All CPU(s) started in SVC mode. [ 0.008215] devtmpfs: initialized [ 0.033305] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.033982] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.034031] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.034211] pinctrl core: initialized pinctrl subsystem [ 0.036250] NET: Registered protocol family 16 [ 0.036763] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.039295] cpuidle: using governor menu [ 0.073850] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.073880] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.076081] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.116010] mxs-dma 1804000.dma-apbh: initialized [ 0.120277] SCSI subsystem initialized [ 0.120902] usbcore: registered new interface driver usbfs [ 0.121175] usbcore: registered new interface driver hub [ 0.121417] usbcore: registered new device driver usb [ 0.123011] i2c-gpio i2c_rtc: using pins 48 (SDA) and 49 (SCL) [ 0.123901] i2c-gpio i2c_eeprom1: using pins 76 (SDA) and 67 (SCL) [ 0.124744] i2c-gpio i2c_eeprom2: using pins 70 (SDA) and 71 (SCL) [ 0.126069] i2c i2c-1: IMX I2C adapter registered [ 0.126111] i2c i2c-1: can't use DMA, using PIO instead. [ 0.126503] pps_core: LinuxPPS API ver. 1 registered [ 0.126526] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.126579] PTP clock support registered [ 0.128851] clocksource: Switched to clocksource mxc_timer1 [ 0.152697] NET: Registered protocol family 2 [ 0.153911] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.154035] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.154191] TCP: Hash tables configured (established 4096 bind 4096) [ 0.154311] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.154364] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.154677] NET: Registered protocol family 1 [ 0.155490] RPC: Registered named UNIX socket transport module. [ 0.155523] RPC: Registered udp transport module. [ 0.155537] RPC: Registered tcp transport module. [ 0.155551] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.733498] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.748592] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.750881] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.761179] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.761214] io scheduler noop registered (default) [ 0.766433] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.766475] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.775501] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX [ 1.337049] console [ttymxc0] enabled [ 1.342615] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 55, base_baud = 5000000) is a IMX [ 1.352879] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 56, base_baud = 5000000) is a IMX [ 1.395717] imx_rngc 2284000.rngb: Freescale RNGC registered. [ 1.430717] brd: module loaded [ 1.449779] loop: module loaded [ 1.457779] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.469437] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.476944] libphy: Fixed MDIO Bus: probed [ 1.483492] 20b4000.ethernet supply phy not found, using dummy regulator [ 1.491514] pps pps0: new PPS source ptp0 [ 1.524266] libphy: fec_enet_mii_bus: probed [ 1.530574] fec 20b4000.ethernet eth0: registered PHC device 0 [ 1.648942] 2188000.ethernet supply phy not found, using dummy regulator [ 1.769916] pps pps1: new PPS source ptp1 [ 1.774998] libphy: fec_enet_mii_bus: probed [ 1.782869] fec 2188000.ethernet eth1: registered PHC device 1 [ 1.789428] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.795996] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.801840] usbcore: registered new interface driver cdc_acm [ 1.807536] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.816037] usbcore: registered new interface driver usb-storage [ 1.866623] rtc rtc0: invalid alarm value: 2022-12-2 33:17:0 [ 1.872934] rtc-pcf8563 4-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 1.889162] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1 [ 1.898174] i2c /dev entries driver [ 1.906337] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 1.914564] sdhci: Secure Digital Host Controller Interface driver [ 1.920899] sdhci: Copyright(c) Pierre Ossman [ 1.925286] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.998927] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 2.018479] ledtrig-cpu: registered to indicate activity on CPUs [ 2.037970] random: fast init done [ 2.046363] usbcore: registered new interface driver usbhid [ 2.054107] usbhid: USB HID core driver [ 2.068333] NET: Registered protocol family 17 [ 2.079258] Registering SWP/SWPB emulation handler [ 2.086308] registered taskstats version 1 [ 2.103146] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.126516] rtc-pcf8563 4-0051: setting system clock to 2022-11-30 12:24:36 UTC (1669811076) [ 2.135013] of_cfs_init [ 2.137667] of_cfs_init: OK [ 2.146581] vdd3p0: disabling [ 2.151755] vref-3v3: disabling [ 2.157007] usb1_vbus: disabling [ 2.162393] usb2_vbus: disabling [ 2.175498] Freeing unused kernel memory: 5120K (c0800000 - c0d00000) [ 2.183200] mmc0: new DDR MMC card at address 0001 [ 2.199069] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.207987] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 2.224675] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 2.237835] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB mount: mounting none on /dev/pts failed: No such file or director[ 2.248686] mmcblk0: p1 p2 p3 p4 < p5 p6 > y Boot mode: usbupdate,wb6_update_FACTORYRESET.fit Board is WB6, loading ci_hdrc_imx module [ 2.499825] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 2.504774] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 2.538961] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 2.544628] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.551494] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.558726] usb usb1: Product: EHCI Host Controller [ 2.563638] usb usb1: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd [ 2.570313] usb usb1: SerialNumber: ci_hdrc.0 [ 2.576140] hub 1-0:1.0: USB hub found [ 2.580141] hub 1-0:1.0: 1 port detected [ 2.589747] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.594711] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 2.628944] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.634696] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.641572] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.648811] usb usb2: Product: EHCI Host Controller [ 2.653740] usb usb2: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd [ 2.660402] usb usb2: SerialNumber: ci_hdrc.1 [ 2.666157] hub 2-0:1.0: USB hub found [ 2.670153] hub 2-0:1.0: 1 port detected [ 3.029020] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 3.219857] usb 2-1: New USB device found, idVendor=0424, idProduct=2514 [ 3.226679] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.237035] hub 2-1:1.0: USB hub found [ 3.241356] hub 2-1:1.0: 4 ports detected [ 3.569004] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ 3.721703] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720 [ 3.728707] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.736296] usb 2-1.1: Product: 802.11n WLAN Adapter [ 3.741408] usb 2-1.1: Manufacturer: Realtek [ 3.745728] usb 2-1.1: SerialNumber: 00e04c000001 [ 3.958971] usb 1-1: new high-speed USB device number 2 using ci_hdrc Load modules for USB to work Starting USB update Waiting for USB to settle (0/10) [ 4.170283] usb 1-1: New USB device found, idVendor=0781, idProduct=5567 [ 4.177055] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.184312] usb 1-1: Product: Cruzer Blade [ 4.188429] usb 1-1: Manufacturer: SanDisk [ 4.192601] usb 1-1: SerialNumber: 03029713012721164642 [ 4.199635] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.206543] scsi host0: usb-storage 1-1:1.0 Waiting for USB to settle (1/10) [ 5.291569] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6 [ 5.304285] sd 0:0:0:0: [sda] 60088320 512-byte logical blocks: (30.8 GB/28.7 GiB) [ 5.316489] sd 0:0:0:0: [sda] Write Protect is off [ 5.323217] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.360740] sda: sda1 [ 5.373757] sd 0:0:0:0: [sda] Attached SCSI removable disk umount: can't umount /usb: Invalid argument Looking for wb6_update_FACTORYRESET.fit on /dev/sda umount: can't umount /usb: Invalid argument mount: mounting /dev/sda on /usb failed: Invalid argument Looking for wb6_update_FACTORYRESET.fit on /dev/sda1 umount: can't umount /usb: Invalid argument [ 6.134453] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. BusyBox v1.22.1 (Debian 1:1.22.0-19+b3) built-in shell (ash) Enter 'help' for a list of built-in commands. ~ # ############################################################################## FACTORY RESET REQUESTED This WILL destroy ALL YOUR DATA: configuration, scripts, files in home directory! If you are ABSOLUTELY SURE that you want to reset Wiren Board to factory condition, hold the FW button for 4 seconds. If you will not do it in 10 seconds, the controller will reboot without firmware update. If you want to perform a regular firmware update, rename FIT file to "wbX_update.fit" without "factory-reset" suffix. ############################################################################## oooo.... Factory reset is confirmed! =============================================================================== Wed Nov 30 12:24:50 UTC 2022: started update from /usb/wb6_update_FACTORYRESET.fit =============================================================================== Description: WirenBoard firmware update Compatible device: contactless,imx6ul-wirenboard61 Firmware version: 202002171718 Firmware compatible: unknown Time of creation: Mon Feb 17 17:20:25 UTC 2020 =============================================================================== >>> Checking SHA1 hash of install PROGRESS: 0% >>> SHA1 hash of install ok >>> Wiping data partition (factory reset) mke2fs 1.43.4 (31-Jan-2017) ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/mmcblk0p6 is mounted. Discarding device blocks: [ 17.781305] random: crng init done done Creating filesystem with 1264896 4k blocks and 316368 inodes Filesystem UUID: 8bdd313f-ee07-489e-ac69-78e68f8dceda Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Allocating group tables: done Writing inode tables: done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: done >>> Extracting install script >>> Running install script >>> Checking SHA1 hash of rootfs PROGRESS: 100% >>> SHA1 hash of rootfs ok >>> Installing firmware update >>> Getting mmcpart from U-Boot environment >>> Will install to /dev/mmcblk0p3 >>> Check if partition table is correct [ 58.274487] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) >>> Mounting /dev/mmcblk0p3 at /dev/shm/rootfs [ 58.312124] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) >>> Cleaning up /dev/mmcblk0p3 >>> Cleaning up using rsync >>> Extracting files to new rootfs /dev/shm/rootfs / PROGRESS: 100% / >>> Recovering device certificates [ 139.523128] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities [ 139.590076] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities [ 139.653887] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null) >>> Unmounting new rootfs >>> Switching to new rootfs >>> Done, removing firmware image and rebooting [ 143.032488] ci_hdrc ci_hdrc.1: remove, state 1 [ 143.036984] usb usb2: USB disconnect, device number 1 [ 143.042323] usb 2-1: USB disconnect, device number 2 [ 143.047304] usb 2-1.1: USB disconnect, device number 3 [ 143.058224] ci_hdrc ci_hdrc.1: USB bus 2 deregistered [ 143.063780] ci_hdrc ci_hdrc.0: remove, state 1 [ 143.068266] usb usb1: USB disconnect, device number 1 [ 143.073461] usb 1-1: USB disconnect, device number 2 [ 143.201010] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 143.231218] reboot: Restarting system U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010c0108 .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3b3c .p0_mpwrdlctl = 0x3f3f3833 .p0_mpwldectrl0 = 0x00090009 .p0_mpwldectrl1 = 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 47C Reset cause: WDOG Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot MMC Device 1 not found no mmc device at slot 1 SD/MMC found on device 1 MMC Device 1 not found ** Bad device mmc 1 ** Running default loadzimage ... MMC Device 1 not found ** Bad device mmc 1 ** => ▒ U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x01090108 .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3b3c .p0_mpwrdlctl = 0x3f3f3833 .p0_mpwldectrl0 = 0x00090009 .p0_mpwldectrl1 = 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 0 Writing to MMC(0)... done Warning: Bootlimit (3) exceeded. Using altbootcmd. Switching to rootfs on partition 2 Saving Environment to MMC... Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot MMC Device 1 not found no mmc device at slot 1 SD/MMC found on device 1 MMC Device 1 not found ** Bad device mmc 1 ** Running default loadzimage ... MMC Device 1 not found ** Bad device mmc 1 ** => U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010c0108 .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3b3c .p0_mpwrdlctl = 0x3f3f3833 .p0_mpwldectrl0 = 0x00090009 .p0_mpwldectrl1 = 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot MMC Device 1 not found no mmc device at slot 1 SD/MMC found on device 1 MMC Device 1 not found ** Bad device mmc 1 ** Running default loadzimage ... MMC Device 1 not found ** Bad device mmc 1 ** =>