=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.09.06 15:35:21 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x010c010c .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3a3f .p0_mpwrdlctl= 0x3f3f3835 .p0_mpwldectrl0= 0x000b000b .p0_mpwldectrl1= 0x000c000c Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3 2 1 0 Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot MMC Device 1 not found no mmc device at slot 1 SD/MMC found on device 1 MMC Device 1 not found ** Bad device mmc 1 ** Running default loadzimage ... MMC Device 1 not found ** Bad device mmc 1 ** => => U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01090109 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3a3f .p0_mpwrdlctl= 0x3f3f3631 .p0_mpwldectrl0= 0x000b000b .p0_mpwldectrl1= 0x000c000c Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 44C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3 2 1 0 Writing to MMC(0)... done Warning: Bootlimit (3) exceeded. Using altbootcmd. Switching to rootfs on partition 3 Saving Environment to MMC... Writing to MMC(0)... done Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot MMC Device 1 not found no mmc device at slot 1 SD/MMC found on device 1 MMC Device 1 not found ** Bad device mmc 1 ** Running default loadzimage ... MMC Device 1 not found ** Bad device mmc 1 ** =>