##############################
# Detected USB flash drive with update file
# Filename: wb6_update.fit
# Press a FW key if you want to update firmware from this file
# or wait 3 seconds to boot normally.
##############################
USB update procedure start
Checking if ubootenv part is present
## Loading FIT header to 0x82000000 ...
reading wb6_update.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update.fit
FAT: Misaligned buffer address (820020c8)
   Skip 7928976 bytes of data
reading wb6_update.fit
FAT: Misaligned buffer address (8200042c)
   Skip 46505 bytes of data
reading wb6_update.fit
FAT: Misaligned buffer address (82000e74)
   Skip 4917 bytes of data
   Skip 173108364 bytes of data
reading wb6_update.fit
** wb6_update.fit shorter than offset + len **
Can't find subimage 'ubootenv'
Extracting kernel
## Loading FIT header to 0x82000000 ...
reading wb6_update.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update.fit
FAT: Misaligned buffer address (820020c8)
reading wb6_update.fit
7945616 bytes read in 4686 ms (1.6 MiB/s)
     Description:  Update kernel
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x82000300
     Data Size:    7928976 Bytes = 7.6 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: unavailable
     Entry Point:  unavailable
     Hash algo:    sha1
     Hash value:   47f6419e0d5d8326c41b16761827dc3d746fec78
## Verifying ... sha1+
   Loading part 0 ... OK
Extracting DTB
## Loading FIT header to 0x83000000 ...
reading wb6_update.fit
## Loading FIT strings to 0x83000028 ...
reading wb6_update.fit
## Loading FIT struct to 0x83000100 ...
reading wb6_update.fit
FAT: Misaligned buffer address (830020c8)
   Skip 7928976 bytes of data
reading wb6_update.fit
FAT: Misaligned buffer address (8300042c)
reading wb6_update.fit
63589 bytes read in 487 ms (127 KiB/s)
     Description:  Update DTB
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x83000440
     Data Size:    46505 Bytes = 45.4 KiB
     Architecture: ARM
     Hash algo:    sha1
     Hash value:   ef9dd3fe2b348fb8eb9f150b9dc2e27d6899e823
## Verifying ... sha1+
   Loading part 0 ... OK
## Flattened Device Tree blob at 83000000
   Booting using the fdt blob at 0x83000000
   Loading Device Tree to bef61000, end bef6f5a8 ... OK

Starting kernel ...


U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38)
DRAM init ok, rows:16, ncs:1, size: 1024MB
.p0_mpdgctrl0   = 0x011b011b
.p0_mpdgctrl1   = 0x0e3f0e3f
.p0_mprddlctl   = 0x3f3f3e43
.p0_mpwrdlctl   = 0x3f3f3b35
.p0_mpwldectrl0 = 0x000e000e
.p0_mpwldectrl1 = 0x000f000f
Trying to boot from MMC1
Warning - USDHC2 controller not supporting


U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000)

CPU:   Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 32C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   eth0: ethernet@02188000
Hit any key to stop autoboot:  0
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
  Device 0: Vendor: Kingston Rev:  Prod: DataTraveler 3.0
            Type: Removable Hard Disk
            Capacity: 14755.2 MB = 14.4 GB (30218842 x 512)
reading wb6_update.fit
1 bytes read in 18 ms (0 Bytes/s)

##############################
# Detected USB flash drive with update file
# Filename: wb6_update.fit
# Press a FW key if you want to update firmware from this file
# or wait 3 seconds to boot normally.
##############################