U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file MMC: no card present Couldn't find partition mmc 0:1 Can't set block device MMC: no card present Couldn't find partition mmc 0:1 Can't set block device No update detected on microSD card, continuing boot 327 bytes read in 2 ms (159.2 KiB/s) Importing environment from 0x42000000... Checking if uenvcmd is set ... Running default loadzimage ... 6029024 bytes read in 162 ms (35.5 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt sun8i-r40-wirenboard720 54344 bytes read in 5 ms (10.4 MiB/s) 254 bytes read in 3 ms (82 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x42000000 [ 0x000000 - 0x5bfee0 ] ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Device Tree to 49fdd000, end 49ffffff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb104 (jenkins@wbdevenv) (arm-linux-gnueabi hf-gcc (Debian 6.3.0-18) 6.3.0 20170516, GNU ld (GNU Binutils for Debian) 2.28) #1 SMP Tue Feb 1 09:17:20 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 7.2.0 (A40i) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x7ec00000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 19 pages/cpu s47884 r8192 d21748 u77824 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 bootmode=update_auto ro ot=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, li near) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1005604K/1048576K available (9216K kernel code, 1425K rwd ata, 3088K rodata, 1024K init, 296K bss, 26588K reserved, 16384K cma-reserved, 2 45748K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 30646 entries in 60 pages [ 0.000000] ftrace: allocated 60 pages with 4 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x680/0x84c wit h crng_init=0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_ idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000010] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns [ 0.000032] Switching to timer-based delay loop, resolution 41ns [ 0.000503] Console: colour dummy device 80x30 [ 0.000590] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=240000) [ 0.000629] pid_max: default: 32768 minimum: 301 [ 0.000902] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linea r) [ 0.000937] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002139] CPU: Testing write buffer coherency: ok [ 0.002583] /cpus/cpu@0 missing clock-frequency property [ 0.002629] /cpus/cpu@1 missing clock-frequency property [ 0.002673] /cpus/cpu@2 missing clock-frequency property [ 0.002953] /cpus/cpu@3 missing clock-frequency property [ 0.003113] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005389] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.005692] rcu: Hierarchical SRCU implementation. [ 0.006827] smp: Bringing up secondary CPUs ... [ 0.018023] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.029383] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.041898] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.042428] smp: Brought up 1 node, 4 CPUs [ 0.042516] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.042548] CPU: All CPU(s) started in HYP mode. [ 0.042578] CPU: Virtualization extensions available. [ 0.044058] devtmpfs: initialized [ 0.063698] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.064456] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.064529] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.066048] pinctrl core: initialized pinctrl subsystem [ 0.067753] NET: Registered protocol family 16 [ 0.072611] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.074771] thermal_sys: Registered thermal governor 'step_wise' [ 0.075938] No ATAGs? [ 0.076305] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.076332] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.158934] SCSI subsystem initialized [ 0.159269] usbcore: registered new interface driver usbfs [ 0.159347] usbcore: registered new interface driver hub [ 0.159439] usbcore: registered new device driver usb [ 0.159997] mc: Linux media interface: v0.10 [ 0.160057] videodev: Linux video capture interface: v2.00 [ 0.160130] pps_core: LinuxPPS API ver. 1 registered [ 0.160147] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 0.160179] PTP clock support registered [ 0.160527] Advanced Linux Sound Architecture Driver Initialized. [ 0.163236] clocksource: Switched to clocksource arch_sys_counter [ 1.346846] NET: Registered protocol family 2 [ 1.348535] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.348631] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.348787] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.348990] TCP: Hash tables configured (established 8192 bind 8192) [ 1.349212] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.349303] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.349703] NET: Registered protocol family 1 [ 1.350932] RPC: Registered named UNIX socket transport module. [ 1.350960] RPC: Registered udp transport module. [ 1.350976] RPC: Registered tcp transport module. [ 1.350990] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.354490] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counter s available [ 1.356448] Initialise system trusted keyrings [ 1.356773] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 1.371784] NFS: Registering the id_resolver key type [ 1.371860] Key type id_resolver registered [ 1.371878] Key type id_legacy registered [ 1.372483] Key type asymmetric registered [ 1.372507] Asymmetric key parser 'x509' registered [ 1.372671] bounce: pool size: 64 pages [ 1.372733] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47) [ 1.372752] io scheduler mq-deadline registered [ 1.372769] io scheduler kyber registered [ 1.375324] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.540693] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.563931] brd: module loaded [ 1.582457] loop: module loaded [ 1.601357] libphy: Fixed MDIO Bus: probed [ 1.602651] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 1.604834] libphy: sun4i_mii_bus: probed [ 1.607645] CAN device driver interface [ 1.611758] PPP generic driver version 2.4.2 [ 1.612089] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.612112] ehci-platform: EHCI generic platform driver [ 1.613385] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.613424] ohci-platform: OHCI generic platform driver [ 1.616181] usbcore: registered new interface driver usb-storage [ 1.616364] usbcore: registered new interface driver usbserial_generic [ 1.616431] usbserial: USB Serial support registered for generic [ 1.619095] sun6i-rtc 1c20400.rtc: registered as rtc1 [ 1.619119] sun6i-rtc 1c20400.rtc: RTC enabled [ 1.620504] i2c /dev entries driver [ 1.631455] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, now ayout=0) [ 1.636565] ledtrig-cpu: registered to indicate activity on CPUs [ 1.637988] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) fro m 24000000 (24 Mhz) [ 1.638575] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.639222] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.639486] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.639733] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.639923] sun8i-ce 1c15000.crypto: Register cbc(aes) [ 1.640169] sun8i-ce 1c15000.crypto: Register ecb(aes) [ 1.640381] sun8i-ce 1c15000.crypto: Register cbc(des3_ede) [ 1.640583] sun8i-ce 1c15000.crypto: Register ecb(des3_ede) [ 1.640805] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0 [ 1.644700] usbcore: registered new interface driver usbhid [ 1.644727] usbhid: USB HID core driver [ 1.649276] iio-rescale a1-volt: using raw+scale source channel [ 1.649834] iio-rescale a2-volt: using raw+scale source channel [ 1.650325] iio-rescale a3-volt: using raw+scale source channel [ 1.650746] iio-rescale vin-volt: using raw+scale source channel [ 1.656078] NET: Registered protocol family 10 [ 1.657308] Segment Routing with IPv6 [ 1.657399] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.659618] NET: Registered protocol family 17 [ 1.659669] can: controller area network core [ 1.659862] NET: Registered protocol family 29 [ 1.659888] can: raw protocol [ 1.659913] can: broadcast manager protocol [ 1.659948] can: netlink gateway - max_hops=1 [ 1.660325] Key type dns_resolver registered [ 1.660533] Registering SWP/SWPB emulation handler [ 1.660682] registered taskstats version 1 [ 1.660757] Loading compiled-in X.509 certificates [ 1.694924] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.702780] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 1.704300] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dum my regulator [ 1.711600] printk: console [ttyS0] disabled [ 1.711767] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 52, base_baud = 15 00000) is a Allwinner sun4i [ 2.670496] printk: console [ttyS0] enabled [ 2.676474] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PI regulator [ 2.683315] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 274 [ 2.690043] sun4i-pinctrl 1c20800.pinctrl: pin-274 (1c28800.serial) status -5 17 [ 2.697474] sun4i-pinctrl 1c20800.pinctrl: could not request pin 274 (PI18) f rom group PI18 on device 1c20800.pinctrl [ 2.708211] dw-apb-uart 1c28800.serial: Error applying setting, reverse thing s back [ 2.716666] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 2.725322] libphy: sun4i_mii_bus: probed [ 2.730994] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.737837] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 236 [ 2.744799] sun4i-pinctrl 1c20800.pinctrl: pin-236 (1c20800.pinctrl:236) stat us -517 [ 2.754894] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.761719] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 232 [ 2.768403] sun4i-pinctrl 1c20800.pinctrl: pin-232 (1c0b000.ethernet) status -517 [ 2.775924] sun4i-pinctrl 1c20800.pinctrl: could not request pin 232 (PH8) fr om group PH8 on device 1c20800.pinctrl [ 2.786457] sun4i-emac 1c0b000.ethernet: Error applying setting, reverse thin gs back [ 2.795901] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 2.802701] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 2.809164] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -5 17 [ 2.816538] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 2.826988] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse thi ngs back [ 2.856146] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 2.872777] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-00 34/axp221-pek/input/input0 [ 2.895622] vcc-3v3: supplied by regulator-dummy [ 2.901384] vdd-cpu: supplied by regulator-dummy [ 2.907119] vdd-sys: supplied by regulator-dummy [ 2.912747] dcdc4: supplied by regulator-dummy [ 2.917922] vcc-dram: Bringing 1500000uV into 1350000-1350000uV [ 2.924956] vcc-dram: supplied by regulator-dummy [ 2.929888] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER [ 2.937177] vcc-gmac-phy: supplied by vcc-3v3 [ 2.942922] random: fast init done [ 2.947892] dc5ldo: supplied by vcc-dram [ 2.953381] tv: Bringing 700000uV into 3300000-3300000uV [ 2.959759] tv: supplied by regulator-dummy [ 2.964967] aldo2: Bringing 2500000uV into 3300000-3300000uV [ 2.971550] aldo2: supplied by regulator-dummy [ 2.977697] avcc-pll: supplied by regulator-dummy [ 2.983538] eldo1: supplied by regulator-dummy [ 2.989096] eldo2: supplied by regulator-dummy [ 2.994286] vcc-pe: Bringing 1200000uV into 1800000-1800000uV [ 3.002011] vcc-pe: supplied by regulator-dummy [ 3.008215] vcc-sd-alt: Bringing 700000uV into 1800000-1800000uV [ 3.015501] vcc-sd-alt: supplied by regulator-dummy [ 3.021494] dldo2: supplied by regulator-dummy [ 3.027147] dldo3: supplied by regulator-dummy [ 3.032678] dldo4: supplied by regulator-dummy [ 3.037851] rtc_ldo: supplied by regulator-dummy [ 3.043561] ldo_io0: supplied by regulator-dummy [ 3.049174] ldo_io1: supplied by regulator-dummy [ 3.064881] axp20x-adc axp22x-adc: DMA mask not set [ 3.071299] axp20x-i2c 0-0034: AXP20X driver loaded [ 3.114183] rtc rtc0: Power loss detected, invalid time [ 3.119685] rtc-pcf85063 2-0051: registered as rtc0 [ 3.134111] rtc rtc0: Power loss detected, invalid time [ 3.139423] rtc-pcf85063 2-0051: setting system clock to 2025-12-08T19:49:21 UTC (1765223361) [ 3.158596] lm75 2-0048: supply vs not found, using dummy regulator [ 3.170237] lm75 2-0048: hwmon0: sensor 'lm75b' [ 3.210213] at24 3-0050: supply vcc not found, using dummy regulator [ 3.218216] at24 3-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 3.236140] i2c-gpio i2c_eeprom1: using lines 48 (SDA) and 49 (SCL) [ 3.248271] at24 4-0050: supply vcc not found, using dummy regulator [ 3.256213] at24 4-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 3.268595] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, u ses new timings mode [ 3.274139] i2c-gpio i2c_eeprom2: using lines 46 (SDA) and 47 (SCL) [ 3.284173] sun4i-usb-phy 1c13400.phy: phy0 dr_mode=3 [ 3.292831] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 53, base_baud = 15 00000) is a Allwinner sun4i [ 3.303354] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 3.311342] libphy: sun4i_mii_bus: probed [ 3.388573] mmc0: new DDR MMC card at address 0001 [ 3.394300] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 3.399204] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 3.405627] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 3.411881] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (246: 0) [ 3.422420] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 3.459594] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 65 MAC: e8:eb :1b:3f:a9:ce [ 3.468922] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 3.475324] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 3.484272] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 3.490381] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supporte d [ 3.497644] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supporte d [ 3.504888] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 3.509853] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 3.516657] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 3.522315] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 3.528669] libphy: stmmac: probed [ 3.785809] ehci-platform 1c14000.usb: EHCI Host Controller [ 3.791419] ehci-platform 1c14000.usb: new USB bus registered, assigned bus n umber 1 [ 3.799589] ehci-platform 1c14000.usb: irq 37, io mem 0x01c14000 [ 3.833220] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 3.840340] hub 1-0:1.0: USB hub found [ 3.844214] hub 1-0:1.0: 1 port detected [ 3.849392] ehci-platform 1c19000.usb: EHCI Host Controller [ 3.855023] ehci-platform 1c19000.usb: new USB bus registered, assigned bus n umber 2 [ 3.863019] ehci-platform 1c19000.usb: irq 39, io mem 0x01c19000 [ 3.893218] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 3.900235] hub 2-0:1.0: USB hub found [ 3.904063] hub 2-0:1.0: 1 port detected [ 3.909188] ehci-platform 1c1c000.usb: EHCI Host Controller [ 3.914807] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus n umber 3 [ 3.922793] ehci-platform 1c1c000.usb: irq 41, io mem 0x01c1c000 [ 3.953686] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 3.960685] hub 3-0:1.0: USB hub found [ 3.964517] hub 3-0:1.0: 1 port detected [ 4.063431] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 4.070074] ohci-platform 1c14400.usb: new USB bus registered, assigned bus n umber 4 [ 4.078049] ohci-platform 1c14400.usb: irq 38, io mem 0x01c14400 [ 4.158164] hub 4-0:1.0: USB hub found [ 4.161991] hub 4-0:1.0: 1 port detected [ 4.167203] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 4.173865] ohci-platform 1c19400.usb: new USB bus registered, assigned bus n umber 5 [ 4.181887] ohci-platform 1c19400.usb: irq 40, io mem 0x01c19400 [ 4.258145] hub 5-0:1.0: USB hub found [ 4.261969] hub 5-0:1.0: 1 port detected [ 4.267263] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 4.273946] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus n umber 6 [ 4.281746] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 4.289032] ohci-platform 1c1c400.usb: irq 42, io mem 0x01c1c400 [ 4.333221] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 4.368146] hub 6-0:1.0: USB hub found [ 4.371952] hub 6-0:1.0: 1 port detected [ 4.378077] of_cfs_init [ 4.379386] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 4.380657] of_cfs_init: OK [ 4.392469] ALSA device list: [ 4.395506] No soundcards found. [ 4.410471] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 4.428889] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesyst em [ 4.436262] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 4.616393] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.623381] scsi host0: usb-storage 1-1:1.0 [ 4.912429] EXT4-fs (mmcblk0p2): orphan cleanup on readonly fs [ 4.931213] EXT4-fs (mmcblk0p2): 1 truncate cleaned up [ 4.936418] EXT4-fs (mmcblk0p2): recovery complete [ 4.954072] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null) [ 4.962259] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 4.969969] devtmpfs: mounted [ 4.978368] Freeing unused kernel memory: 1024K [ 4.983122] Run /sbin/init as init process [ 5.213170] random: systemd: uninitialized urandom read (16 bytes read) [ 5.224704] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SEL INUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL + XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 5.244835] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 5.284044] systemd[1]: Set hostname to . [ 5.308640] random: systemd: uninitialized urandom read (16 bytes read) [ 5.323108] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d) [ 5.579239] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 5.613710] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 5.643614] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 5.683796] systemd[1]: Started Dispatch Password Requests to Console Directo ry Watch. [ 5.684457] scsi 0:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ : 0 ANSI: 2 [ OK ] Started Dispatch Password Requests to Consol[ 5.702410] sd 0:0:0:0: [sda] 3944448 512-byte logical blocks: (2.02 GB/1.88 GiB) e Directory Watch. [ 5.714642] sd 0:0:0:0: [sda] Write Protect is off [ 5.721140] sd 0:0:0:0: [sda] No Caching mode page found [ 5.726486] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 5.744253] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 5.774030] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 5.806933] systemd[1]: Mounting Debug File System... Mounting Debug File System... Mounting POSIX Message Queue File System... [ 5.855910] sda: sda1 [ 5.862256] sd 0:0:0:0: [sda] Attached SCSI removable disk [ OK ] Listening on Journal Socket. [ OK ] Created slice system-systemd\x2dfsck.slice. [ OK ] Reached target Slices. Starting File System Check on Root Device... [ OK ] Created slice system-getty.slice. Starting Create list of required st…ce nodes for the current kernel... [ OK ] Listening on udev Kernel Socket. Starting Load Kernel Modules... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting /sys/kernel/config... [ OK ] Listening on udev Control Socket. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted /sys/kernel/config. [ OK ] Started Journal Service. [ OK ] Started File System Check on Root Device. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Started File System Check Daemon to report status. Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev... Starting Remount Root and Kernel File Systems... [ 6.768322] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ OK ] Started Apply Kernel Variables. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Remount Root and Kernel File Systems. Starting prepare partitions at first boot... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting udev Kernel Device Manager... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started prepare partitions at first boot. [ OK ] Reached target Local File Systems (Pre). [ 7.650983] Driver for 1-wire Dallas network protocol. [ OK ] Started udev Coldplug all Devices. [ 7.828120] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, usi ng dummy regulator [ 8.012009] Bluetooth: Core ver 2.22 [ 8.015834] NET: Registered protocol family 31 [ 8.020296] Bluetooth: HCI device and connection manager initialized [ 8.026655] cfg80211: Loading compiled-in X.509 certificates for regulatory d atabase [ 8.034577] Bluetooth: HCI socket layer initialized [ 8.039544] Bluetooth: L2CAP socket layer initialized [ 8.044760] Bluetooth: SCO socket layer initialized [ OK ] Found device /dev/mmcblk0p6. [ 8.107501] usbcore: registered new interface driver btusb [ 8.116421] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=0 6 lmp_subver=8723 [ 8.135145] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 8.141211] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ OK ] Found device /dev/ttyS0. [ 8.152931] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 8.159808] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.b in failed with error -2 [ 8.169096] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 [ 8.184594] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 8.199469] platform regulatory.0: Direct firmware load for regulatory.db fai led with error -2 [ 8.208406] cfg80211: failed to load regulatory.db [ OK ] Found device /dev/mmcblk0p5. Activating swap /dev/mmcblk0p5... Starting File System Check on /dev/mmcblk0p6... [ 8.663479] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 acr oss:262140k SS [ 8.692573] RTL871X: module init start [ OK ] Activated swap /dev/mmcblk0p5.[ 8.696507] RTL871X: rtl8723bu v4.3.6. 11_12942.20141204_BTCOEX20140507-4E40 [ 8.707915] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ 8.921292] RTL871X: rtw_ndev_init(wlan0) [ 8.926715] RTL871X: rtw_ndev_init(wlan1) [ 8.932229] usbcore: registered new interface driver rtl8723bu [ 8.938191] RTL871X: module init ret=0 [ OK ] Started File System Check on /dev/mmcblk0p6. [ 9.002356] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 [ 9.097121] usbcore: registered new interface driver rtl8xxxu [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Mounting /mnt/data... [ OK ] Reached target Swap. [ 9.755791] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. O pts: (null) [ OK ] Mounted /mnt/data. Starting Load/Save RF Kill Switch Status... Mounting /var/log... [ OK ] Mounted /var/log. [ OK ] Started Load/Save RF Kill Switch Status. Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems. [ OK ] Started ifup for eth1. Starting prepare mounts and symlinks to config files... Starting Raise network interfaces... [ 10.071778] systemd-journald[126]: Received request to flush runtime journal from PID 1 [ OK ] Started Raise network interfaces. [ 10.117832] systemd-journald[126]: File /var/log/journal/93fb028105133f2a3b0b cde661fb8c16/system.journal corrupted or uncleanly shut down, renaming and repla cing. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Monitor directories with device templates for wb-mqtt-serial. [ OK ] Reached target Paths. [ OK ] Listening on KNX Daemon (socket). [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Bluetooth service... Starting Restore local date from Wiren Board GSM RTC... [ OK ] Started Regular background program processing daemon. Starting Restore /etc/resolv.conf i…fore the ppp link was shut down... [ OK ] Started Cgroup management daemon. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ 11.701504] new mount options do not match the existing superblock, will be i gnored Starting System Logging Service... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Bluetooth service. [ 11.907838] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 11.913327] Bluetooth: BNEP filters: protocol multicast [ 11.918618] Bluetooth: BNEP socket layer initialized [ OK ] Reached target Bluetooth. Starting initialize filesystems at first boot... Starting Login Service... [ OK ] Started Generates wb-mqtt-serial UI schema for wb-mqtt-confed. [ OK ] Started watch config files. Starting Initialize Wiren Board Device Tree overlays... [ OK ] Started System Logging Service. [ OK ] Started Restore /etc/resolv.conf if…before the ppp link was shut down. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [DEPEND] Dependency failed for MQTT Rule engine for Wiren Board. Starting Hostname Service... [ OK ] Started Wiren Board firmware update service. Starting Wiren Board MQTT to Modbus TCP gateway... [ OK ] Started Wiren Board configuration editor backend. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Started initialize filesystems at first boot. [ OK ] Started Login Service. [ OK ] Started Hostname Service. [FAILED] Failed to start Wiren Board MQTT to OPC UA gateway. See 'systemctl status wb-mqtt-opcua.service' for details. [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Reached target Network. Starting dnsmasq - A lightweight DHCP and caching DNS server... Starting KNX Daemon... Starting Permit User Sessions... Starting OpenBSD Secure Shell server... Starting A high performance web server and a reverse proxy server... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started KNX Daemon. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [ OK ] Started Permit User Sessions. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Network is Online. Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Brings up/down network automatically... Starting LSB: Start NTP daemon... Starting Daily apt download activities... [FAILED] Failed to start Wiren Board MQTT to Modbus TCP gateway. See 'systemctl status wb-mqtt-mbgate.service' for details. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [ OK ] Started Initialize Wiren Board Device Tree overlays. [ OK ] Started A high performance web server and a reverse proxy server. [ OK ] Stopped OpenBSD Secure Shell server. [ 14.430305] process '/sbin/netplugd' started with executable stack Starting OpenBSD Secure Shell server... [ OK ] Stopped Wiren Board MQTT to OPC UA gateway. [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Started one-click diagnostic data c…ard, generating archive with data. [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. Starting MQTT Driver for GPIO-controlled switches... Starting KNXD Configurator for Wiren Board... [ OK ] Started MQTT Driver for serial devices. [ OK ] Started Wiren Board MQTT KNX bridge. Starting MQTT Driver for ADC... [ OK ] Started LSB: Start NTP daemon. [ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [ OK ] Stopped Wiren Board MQTT to Modbus TCP gateway. Starting Wiren Board MQTT to Modbus TCP gateway... [ OK ] Started Wiren Board database logger. [ OK ] Started Wiren Board journald to MQTT gateway. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Reached target Host and Network Name Lookups. [ 15.421023] RTL871X: RTW_ADAPTIVITY_EN_ [ 15.421045] AUTO, chplan:0x20, Regulation:3,3 [ 15.429512] RTL871X: RTW_ADAPTIVITY_MODE_ [ 15.429523] NORMAL Starting Compensation of systime in…evice-tree (with opposite sign)... [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [ 15.600160] random: crng init done [ 15.603618] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [ OK ] Stopped Wiren Board configuration editor backend. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [ OK ] Started Compensation of systime in … device-tree (with opposite sign). [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [ OK ] Stopped OpenBSD Secure Shell server. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [ OK ] Started Wiren Board configuration editor backend. Starting Initialize Wiren Board on successful boot... [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [FAILED] Failed to start Wiren Board MQTT to OPC UA gateway. See 'systemctl status wb-mqtt-opcua.service' for details. [FAILED] Failed to start Wiren Board MQTT to Modbus[ 17.199467] RTL871X: assoc success TCP gateway. [ 17.204406] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 17.213655] sun4i-emac 1c0b000.ethernet eth0: Link is Up - 100Mbps/Full - flo w control off See 'systemctl status wb-mqtt-mbgate.service' for details. [ 17.325164] dwmac-sun8i 1c50000.ethernet eth1: PHY [stmmac-0:00] driver [ICPl us IP101A/G] (irq=POLL) [ 17.385915] dwmac-sun8i 1c50000.ethernet eth1: No Safety Features support fou nd [ 17.393375] dwmac-sun8i 1c50000.ethernet eth1: No MAC Management Counters ava ilable [ 17.401086] dwmac-sun8i 1c50000.ethernet eth1: PTP not supported by HW [ 17.548038] dwmac-sun8i 1c50000.ethernet eth1: configuring for phy/mii link m ode [ 17.582312] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started LSB: Advanced IEEE 802.11 management daemon. [ OK ] Stopped KNX Daemon. Starting KNX Daemon... [ OK ] Started Daily apt download activities. Starting Daily apt upgrade and clean activities... [ OK ] Started KNX Daemon. [ OK ] Started KNXD Configurator for Wiren Board. [ OK ] Stopped Wiren Board MQTT to OPC UA gateway. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Stopped Kernel 1-Wire MQTT driver for WB-HomA. [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. [ OK ] Stopped Wiren Board MQTT KNX bridge. [ OK ] Started Wiren Board MQTT KNX bridge. [ OK ] Stopped Wiren Board MQTT to Modbus TCP gateway. Starting Wiren Board MQTT to Modbus TCP gateway... Debian GNU/Linux 9 wirenboard-AXA7MZP5 ttyS0 wirenboard-AXA7MZP5 login: [ 34.403526] vcc-gmac-phy: disabling [ 34.407521] dc5ldo: disabling [ 34.411941] dldo4: disabling [ 34.416656] vcc-sd: disabling [ 74.632708] systemd-journald[126]: Received SIGTERM from PID 5818 (watchdog). [ 74.887052] systemd[1]: Started MQTT Driver for ADC. [ 74.926160] systemd[1]: Reexecuting. [ 75.135056] printk: systemd: 21 output lines suppressed due to ratelimiting [ 78.964986] RTL871X: nolinked power save enter [ 79.876106] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 79.933325] sun4i-emac 1c0b000.ethernet eth0: Link is Down U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode .................................. Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file MMC: no card present Couldn't find partition mmc 0:1 Can't set block device MMC: no card present Couldn't find partition mmc 0:1 Can't set block device No update detected on microSD card, continuing boot 327 bytes read in 2 ms (159.2 KiB/s) Importing environment from 0x42000000... Checking if uenvcmd is set ... Running default loadzimage ... 6029024 bytes read in 162 ms (35.5 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt sun8i-r40-wirenboard720 54344 bytes read in 6 ms (8.6 MiB/s) 254 bytes read in 3 ms (82 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x42000000 [ 0x000000 - 0x5bfee0 ] ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Device Tree to 49fdd000, end 49ffffff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb104 (jenkins@wbdevenv) (arm-linux-gnueabi hf-gcc (Debian 6.3.0-18) 6.3.0 20170516, GNU ld (GNU Binutils for Debian) 2.28) #1 SMP Tue Feb 1 09:17:20 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 7.2.0 (A40i) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x7ec00000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 19 pages/cpu s47884 r8192 d21748 u77824 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 bootmode=update_auto ro ot=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, li near) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1005604K/1048576K available (9216K kernel code, 1425K rwd ata, 3088K rodata, 1024K init, 296K bss, 26588K reserved, 16384K cma-reserved, 2 45748K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 30646 entries in 60 pages [ 0.000000] ftrace: allocated 60 pages with 4 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x680/0x84c wit h crng_init=0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_ idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000013] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns [ 0.000041] Switching to timer-based delay loop, resolution 41ns [ 0.000620] Console: colour dummy device 80x30 [ 0.000722] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=240000) [ 0.000769] pid_max: default: 32768 minimum: 301 [ 0.001083] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linea r) [ 0.001121] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002432] CPU: Testing write buffer coherency: ok [ 0.002902] /cpus/cpu@0 missing clock-frequency property [ 0.002951] /cpus/cpu@1 missing clock-frequency property [ 0.002998] /cpus/cpu@2 missing clock-frequency property [ 0.003048] /cpus/cpu@3 missing clock-frequency property [ 0.003067] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005446] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.005816] rcu: Hierarchical SRCU implementation. [ 0.007097] smp: Bringing up secondary CPUs ... [ 0.018370] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.029804] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.041022] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.041229] smp: Brought up 1 node, 4 CPUs [ 0.041270] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.041284] CPU: All CPU(s) started in HYP mode. [ 0.041297] CPU: Virtualization extensions available. [ 0.043422] devtmpfs: initialized [ 0.062963] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.063280] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.063317] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.065792] pinctrl core: initialized pinctrl subsystem [ 0.067764] NET: Registered protocol family 16 [ 0.072645] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.074065] thermal_sys: Registered thermal governor 'step_wise' [ 0.075253] No ATAGs? [ 0.075909] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.075954] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.159547] SCSI subsystem initialized [ 0.159895] usbcore: registered new interface driver usbfs [ 0.159977] usbcore: registered new interface driver hub [ 0.160077] usbcore: registered new device driver usb [ 0.160656] mc: Linux media interface: v0.10 [ 0.160717] videodev: Linux video capture interface: v2.00 [ 0.160790] pps_core: LinuxPPS API ver. 1 registered [ 0.160808] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 0.160842] PTP clock support registered [ 0.161205] Advanced Linux Sound Architecture Driver Initialized. [ 0.163662] clocksource: Switched to clocksource arch_sys_counter [ 1.360205] NET: Registered protocol family 2 [ 1.361365] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.361445] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.361566] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.361726] TCP: Hash tables configured (established 8192 bind 8192) [ 1.361914] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.361995] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.362311] NET: Registered protocol family 1 [ 1.364739] RPC: Registered named UNIX socket transport module. [ 1.364798] RPC: Registered udp transport module. [ 1.364834] RPC: Registered tcp transport module. [ 1.364869] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.367447] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counter s available [ 1.370440] Initialise system trusted keyrings [ 1.370970] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 1.384872] NFS: Registering the id_resolver key type [ 1.384963] Key type id_resolver registered [ 1.384979] Key type id_legacy registered [ 1.386483] Key type asymmetric registered [ 1.386538] Asymmetric key parser 'x509' registered [ 1.386935] bounce: pool size: 64 pages [ 1.387060] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47) [ 1.387099] io scheduler mq-deadline registered [ 1.387133] io scheduler kyber registered [ 1.388858] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.548457] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.572931] brd: module loaded [ 1.590649] loop: module loaded [ 1.609125] libphy: Fixed MDIO Bus: probed [ 1.612165] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 1.613069] libphy: sun4i_mii_bus: probed [ 1.616874] CAN device driver interface [ 1.619617] PPP generic driver version 2.4.2 [ 1.619896] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.619915] ehci-platform: EHCI generic platform driver [ 1.622618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.622674] ohci-platform: OHCI generic platform driver [ 1.624315] usbcore: registered new interface driver usb-storage [ 1.624481] usbcore: registered new interface driver usbserial_generic [ 1.624527] usbserial: USB Serial support registered for generic [ 1.628719] sun6i-rtc 1c20400.rtc: registered as rtc1 [ 1.628749] sun6i-rtc 1c20400.rtc: RTC enabled [ 1.629263] i2c /dev entries driver [ 1.640326] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, now ayout=0) [ 1.645534] ledtrig-cpu: registered to indicate activity on CPUs [ 1.646282] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) fro m 24000000 (24 Mhz) [ 1.646714] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.647227] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.648053] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.648734] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 1.649135] sun8i-ce 1c15000.crypto: Register cbc(aes) [ 1.649553] sun8i-ce 1c15000.crypto: Register ecb(aes) [ 1.649881] sun8i-ce 1c15000.crypto: Register cbc(des3_ede) [ 1.650173] sun8i-ce 1c15000.crypto: Register ecb(des3_ede) [ 1.650486] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0 [ 1.652609] usbcore: registered new interface driver usbhid [ 1.652628] usbhid: USB HID core driver [ 1.657606] iio-rescale a1-volt: using raw+scale source channel [ 1.658034] iio-rescale a2-volt: using raw+scale source channel [ 1.659004] iio-rescale a3-volt: using raw+scale source channel [ 1.659963] iio-rescale vin-volt: using raw+scale source channel [ 1.665406] NET: Registered protocol family 10 [ 1.667153] Segment Routing with IPv6 [ 1.667269] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.668194] NET: Registered protocol family 17 [ 1.668228] can: controller area network core [ 1.668329] NET: Registered protocol family 29 [ 1.668346] can: raw protocol [ 1.668362] can: broadcast manager protocol [ 1.668385] can: netlink gateway - max_hops=1 [ 1.668661] Key type dns_resolver registered [ 1.668817] Registering SWP/SWPB emulation handler [ 1.668932] registered taskstats version 1 [ 1.669024] Loading compiled-in X.509 certificates [ 1.705183] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.712070] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 1.713283] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dum my regulator [ 1.721986] printk: console [ttyS0] disabled [ 1.722191] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 52, base_baud = 15 00000) is a Allwinner sun4i [ 2.681094] printk: console [ttyS0] enabled [ 2.687835] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PI regulator [ 2.694668] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 274 [ 2.701286] sun4i-pinctrl 1c20800.pinctrl: pin-274 (1c28800.serial) status -5 17 [ 2.708680] sun4i-pinctrl 1c20800.pinctrl: could not request pin 274 (PI18) f rom group PI18 on device 1c20800.pinctrl [ 2.719436] dw-apb-uart 1c28800.serial: Error applying setting, reverse thing s back [ 2.727964] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 2.736781] libphy: sun4i_mii_bus: probed [ 2.742282] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.749130] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 236 [ 2.755788] sun4i-pinctrl 1c20800.pinctrl: pin-236 (1c20800.pinctrl:236) stat us -517 [ 2.766034] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.772898] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 232 [ 2.779617] sun4i-pinctrl 1c20800.pinctrl: pin-232 (1c0b000.ethernet) status -517 [ 2.787143] sun4i-pinctrl 1c20800.pinctrl: could not request pin 232 (PH8) fr om group PH8 on device 1c20800.pinctrl [ 2.797682] sun4i-emac 1c0b000.ethernet: Error applying setting, reverse thin gs back [ 2.807395] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 2.814222] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 2.820669] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -5 17 [ 2.828059] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 2.838537] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse thi ngs back [ 2.867769] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 2.884515] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-00 34/axp221-pek/input/input0 [ 2.907352] vcc-3v3: supplied by regulator-dummy [ 2.913057] vdd-cpu: supplied by regulator-dummy [ 2.918853] vdd-sys: supplied by regulator-dummy [ 2.924537] dcdc4: supplied by regulator-dummy [ 2.929613] vcc-dram: Bringing 1500000uV into 1350000-1350000uV [ 2.936453] vcc-dram: supplied by regulator-dummy [ 2.941430] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER [ 2.948767] vcc-gmac-phy: supplied by vcc-3v3 [ 2.954618] random: fast init done [ 2.959614] dc5ldo: supplied by vcc-dram [ 2.965194] tv: Bringing 700000uV into 3300000-3300000uV [ 2.971555] tv: supplied by regulator-dummy [ 2.976829] aldo2: Bringing 2500000uV into 3300000-3300000uV [ 2.983342] aldo2: supplied by regulator-dummy [ 2.989499] avcc-pll: supplied by regulator-dummy [ 2.995364] eldo1: supplied by regulator-dummy [ 3.000906] eldo2: supplied by regulator-dummy [ 3.006092] vcc-pe: Bringing 1200000uV into 1800000-1800000uV [ 3.014179] vcc-pe: supplied by regulator-dummy [ 3.019902] vcc-sd-alt: Bringing 700000uV into 1800000-1800000uV [ 3.027169] vcc-sd-alt: supplied by regulator-dummy [ 3.033197] dldo2: supplied by regulator-dummy [ 3.038820] dldo3: supplied by regulator-dummy [ 3.044378] dldo4: supplied by regulator-dummy [ 3.049536] rtc_ldo: supplied by regulator-dummy [ 3.055286] ldo_io0: supplied by regulator-dummy [ 3.060951] ldo_io1: supplied by regulator-dummy [ 3.076669] axp20x-adc axp22x-adc: DMA mask not set [ 3.083068] axp20x-i2c 0-0034: AXP20X driver loaded [ 3.125894] rtc rtc0: Power loss detected, invalid time [ 3.131388] rtc-pcf85063 2-0051: registered as rtc0 [ 3.145852] rtc rtc0: Power loss detected, invalid time [ 3.151163] rtc-pcf85063 2-0051: setting system clock to 2025-12-08T19:51:15 UTC (1765223475) [ 3.170451] lm75 2-0048: supply vs not found, using dummy regulator [ 3.182828] lm75 2-0048: hwmon0: sensor 'lm75b' [ 3.225661] at24 3-0050: supply vcc not found, using dummy regulator [ 3.233668] at24 3-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 3.243662] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, u ses new timings mode [ 3.251647] i2c-gpio i2c_eeprom1: using lines 48 (SDA) and 49 (SCL) [ 3.264744] at24 4-0050: supply vcc not found, using dummy regulator [ 3.272716] at24 4-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 3.290646] i2c-gpio i2c_eeprom2: using lines 46 (SDA) and 47 (SCL) [ 3.297330] sun4i-usb-phy 1c13400.phy: phy0 dr_mode=3 [ 3.305943] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 53, base_baud = 15 00000) is a Allwinner sun4i [ 3.316538] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 3.324579] libphy: sun4i_mii_bus: probed [ 3.338987] mmc0: new DDR MMC card at address 0001 [ 3.344656] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 3.349572] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 3.355942] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 3.362181] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (246: 0) [ 3.372660] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 3.469997] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 65 MAC: e8:eb :1b:3f:a9:ce [ 3.479326] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 3.485737] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 3.494727] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 3.500846] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supporte d [ 3.508115] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supporte d [ 3.515357] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 3.520322] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 3.527121] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 3.532779] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 3.539110] libphy: stmmac: probed [ 3.796197] ehci-platform 1c14000.usb: EHCI Host Controller [ 3.801839] ehci-platform 1c14000.usb: new USB bus registered, assigned bus n umber 1 [ 3.810003] ehci-platform 1c14000.usb: irq 37, io mem 0x01c14000 [ 3.843631] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 3.850729] hub 1-0:1.0: USB hub found [ 3.854630] hub 1-0:1.0: 1 port detected [ 3.859851] ehci-platform 1c19000.usb: EHCI Host Controller [ 3.865497] ehci-platform 1c19000.usb: new USB bus registered, assigned bus n umber 2 [ 3.873540] ehci-platform 1c19000.usb: irq 39, io mem 0x01c19000 [ 3.903630] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 3.910626] hub 2-0:1.0: USB hub found [ 3.914480] hub 2-0:1.0: 1 port detected [ 3.919607] ehci-platform 1c1c000.usb: EHCI Host Controller [ 3.925257] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus n umber 3 [ 3.933262] ehci-platform 1c1c000.usb: irq 41, io mem 0x01c1c000 [ 3.964098] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 3.971076] hub 3-0:1.0: USB hub found [ 3.974946] hub 3-0:1.0: 1 port detected [ 4.073721] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 4.080360] ohci-platform 1c14400.usb: new USB bus registered, assigned bus n umber 4 [ 4.088415] ohci-platform 1c14400.usb: irq 38, io mem 0x01c14400 [ 4.168553] hub 4-0:1.0: USB hub found [ 4.172362] hub 4-0:1.0: 1 port detected [ 4.177568] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 4.184260] ohci-platform 1c19400.usb: new USB bus registered, assigned bus n umber 5 [ 4.192250] ohci-platform 1c19400.usb: irq 40, io mem 0x01c19400 [ 4.268529] hub 5-0:1.0: USB hub found [ 4.272337] hub 5-0:1.0: 1 port detected [ 4.277523] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 4.284214] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus n umber 6 [ 4.292010] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 4.299282] ohci-platform 1c1c400.usb: irq 42, io mem 0x01c1c400 [ 4.343643] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 4.378549] hub 6-0:1.0: USB hub found [ 4.382358] hub 6-0:1.0: 1 port detected [ 4.388504] of_cfs_init [ 4.389866] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 4.391083] of_cfs_init: OK [ 4.402908] ALSA device list: [ 4.405942] No soundcards found. [ 4.420878] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 4.440161] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null) [ 4.448425] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 4.456058] devtmpfs: mounted [ 4.464518] Freeing unused kernel memory: 1024K [ 4.494099] Run /sbin/init as init process [ 4.637357] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.644456] scsi host0: usb-storage 1-1:1.0 [ 4.737802] random: systemd: uninitialized urandom read (16 bytes read) [ 4.749234] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SEL INUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL + XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 4.768069] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 4.804480] systemd[1]: Set hostname to . [ 4.829184] random: systemd: uninitialized urandom read (16 bytes read) [ 4.846376] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d) [ 5.098519] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 5.134138] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 5.174621] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 5.204212] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 5.234157] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 5.275111] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 5.303967] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. Mounting Debug File System... [ OK ] Created slice system-getty.slice. Starting Create list of required st…ce nodes for the current kernel... Mounting /sys/kernel/config... [ OK ] Listening on Syslog Socket. Starting Journal Service... Mounting POSIX Message Queue File System... [ OK ] Listening on fsck to fsckd communication Socket. Starting File System Check on Root Device... [ OK ] Reached target Remote File Systems. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Listening on udev Kernel Socket. [ 5.685014] scsi 0:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ : 0 ANSI: 2 [ 5.695714] sd 0:0:0:0: [sda] 3944448 512-byte logical blocks: (2.02 GB/1.88 GiB) [ 5.704992] sd 0:0:0:0: [sda] Write Protect is off [ 5.710566] sd 0:0:0:0: [sda] No Caching mode page found [ 5.715955] sd 0:0:0:0: [sda] Assuming drive cache: write through [ OK ] Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-serial\x2dgetty.slice. Starting Load Kernel Modules... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Encrypted Volumes. [ 5.876640] sda: sda1 [ 5.882586] sd 0:0:0:0: [sda] Attached SCSI removable disk [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted /sys/kernel/config. [ OK ] Started Journal Service. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started File System Check on Root Device. [ OK ] Started Load Kernel Modules. [ OK ] Started File System Check Daemon to report status. Starting Apply Kernel Variables... Starting Remount Root and Kernel File Systems... Starting Create Static Device Nodes in /dev... [ OK ] Started Apply Kernel Variables. [ 6.364392] random: crng init done [ 6.367816] random: 7 urandom warning(s) missed due to ratelimiting [ 7.046085] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting prepare partitions at first boot... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Load/Save Random Seed. [ OK ] Started prepare partitions at first boot. [ OK ] Reached target Local File Systems (Pre). [ 7.909490] Driver for 1-wire Dallas network protocol. [ OK ] Started udev Coldplug all Devices. [ 8.089777] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, usi ng dummy regulator [ OK ] Found device /dev/ttyS0. [ 8.305770] Bluetooth: Core ver 2.22 [ 8.309494] NET: Registered protocol family 31 [ 8.314072] Bluetooth: HCI device and connection manager initialized [ 8.320491] Bluetooth: HCI socket layer initialized [ 8.325590] Bluetooth: L2CAP socket layer initialized [ 8.330699] Bluetooth: SCO socket layer initialized [ 8.351634] cfg80211: Loading compiled-in X.509 certificates for regulatory d atabase [ 8.352058] usbcore: registered new interface driver btusb [ OK ] Found device /dev/mmcblk0p6.[ 8.371846] Bluetooth: hci0: RTL: examin ing hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [ 8.385998] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 8.392186] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ 8.402638] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 8.410256] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.b in failed with error -2 [ 8.419727] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 [ OK ] Found device /dev/mmcblk0p5. [ 8.480379] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 8.487460] platform regulatory.0: Direct firmware load for regulatory.db fai led with error -2 [ 8.496247] cfg80211: failed to load regulatory.db Activating swap /dev/mmcblk0p5... Starting File System Check on /dev/mmcblk0p6... [ 8.883778] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 acr oss:262140k SS [ OK ] Activated swap /dev/mmcblk0p5. [ 8.979507] RTL871X: module init start [ 8.983303] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40 [ 8.990449] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ OK ] Started File System Check on /dev/mmcblk0p6. [ 9.171413] RTL871X: rtw_ndev_init(wlan0) [ 9.176756] RTL871X: rtw_ndev_init(wlan1) [ 9.182041] usbcore: registered new interface driver rtl8723bu [ 9.187981] RTL871X: module init ret=0 [ 9.247860] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 [ 9.282648] usbcore: registered new interface driver rtl8xxxu [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Mounting /mnt/data... [ OK ] Reached target Swap. [ 9.946367] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. O pts: (null) [ OK ] Mounted /mnt/data. Starting Load/Save RF Kill Switch Status... Mounting /var/log... [ OK ] Mounted /var/log. [ OK ] Started Load/Save RF Kill Switch Status. Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems. Starting prepare mounts and symlinks to config files... [ OK ] Started ifup for eth1. Starting Raise network interfaces... [ 10.291277] systemd-journald[118]: Received request to flush runtime journal from PID 1 [ OK ] Started Raise network interfaces. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Monitor directories with device templates for wb-mqtt-serial. [ OK ] Reached target Paths. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt download activities. [ OK ] Listening on KNX Daemon (socket). [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Bluetooth service... Starting Mosquitto MQTT v3.1/v3.1.1 Broker... Starting Login Service... [ OK ] Started Cgroup management daemon. Starting Restore /etc/resolv.conf i…fore the ppp link was shut down... [ 11.729262] new mount options do not match the existing superblock, will be i gnored Starting Restore local date from Wiren Board GSM RTC... Starting initialize filesystems at first boot... Starting System Logging Service... [ OK ] Started Generates wb-mqtt-serial UI schema for wb-mqtt-confed. [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. [ OK ] Started Bluetooth service. [ OK ] Reached target Bluetooth. [ 12.108955] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 12.115293] Bluetooth: BNEP filters: protocol multicast [ 12.120604] Bluetooth: BNEP socket layer initialized [ OK ] Started watch config files. Starting Initialize Wiren Board Device Tree overlays... [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [DEPEND] Dependency failed for MQTT Rule engine for Wiren Board. [ OK ] Started Restore /etc/resolv.conf if…before the ppp link was shut down. [ OK ] Started Login Service. [ OK ] Started initialize filesystems at first boot. [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... Starting A high performance web server and a reverse proxy server... Starting dnsmasq - A lightweight DHCP and caching DNS server... Starting Permit User Sessions... Starting KNX Daemon... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... Starting Hostname Service... [ OK ] Started KNX Daemon. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [ OK ] Started Permit User Sessions. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Hostname Service. [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Network is Online. Starting LSB: Start NTP daemon... Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Brings up/down network automatically... [ OK ] Started Initialize Wiren Board Device Tree overlays. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [ OK ] Started A high performance web server and a reverse proxy server. [ 14.092620] process '/sbin/netplugd' started with executable stack [ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server. [ OK ] Started LSB: Start NTP daemon. Starting Compensation of systime in…evice-tree (with opposite sign)... [ OK ] Reached target Host and Network Name Lookups. [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... Starting KNXD Configurator for Wiren Board... [ OK ] Started one-click diagnostic data c…ard, generating archive with data. [ OK ] Started Wiren Board MQTT KNX bridge. Starting MQTT Driver for GPIO-controlled switches... [ OK ] Started MQTT Driver for serial devices. [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. Starting MQTT Driver for ADC... [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... Starting Wiren Board MQTT to Modbus TCP gateway... [ 14.981044] RTL871X: RTW_ADAPTIVITY_EN_ [ 14.981072] AUTO, chplan:0x20, Regulation:3,3 [ 14.989490] RTL871X: RTW_ADAPTIVITY_MODE_ [ 14.989500] NORMAL [ OK ] Started Wiren Board firmware update service. [ OK ] Started Wiren Board journald to MQTT gateway. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Started Wiren Board configuration editor backend. [ OK ] Started Wiren Board database logger. [ OK ] Started Compensation of systime in … device-tree (with opposite sign). [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. Starting Initialize Wiren Board on successful boot... [ OK ] Stopped Mosquitto MQTT v3.1/v3.1.1 Broker. [FAILED] Failed to start Mosquitto MQTT v3.1/v3.1.1 Broker. See 'systemctl status mosquitto.service' for details. [ OK ] Stopped OpenBSD Secure Shell server. [FAILED] Failed to start OpenBSD Secure Shell server. See 'systemctl status ssh.service' for details. [FAILED] Failed to start Wiren Board MQTT to OPC UA gateway. See 'systemctl status wb-mqtt-opcua.service' for details. [ OK ] Stopped KNX Daemon. [ 17.053830] sun4i-emac 1c0b000.ethernet eth0: Link is Up - 100Mbps/Full - flo w control off [ 17.062214] RTL871X: assoc success Starting KNX Daemon... [ 17.193709] dwmac-sun8i 1c50000.ethernet eth1: PHY [stmmac-0:00] driver [ICPl us IP101A/G] (irq=POLL) [ 17.227572] dwmac-sun8i 1c50000.ethernet eth1: No Safety Features support fou nd [ 17.235037] dwmac-sun8i 1c50000.ethernet eth1: No MAC Management Counters ava ilable [ 17.242763] dwmac-sun8i 1c50000.ethernet eth1: PTP not supported by HW [FAILED] Failed to start Wiren Board MQTT to Modbus TCP gateway. See 'systemctl status wb-mqtt-mbgate.service' for details. [ 17.348002] dwmac-sun8i 1c50000.ethernet eth1: configuring for phy/mii link m ode [ 17.376215] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 17.383022] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ OK ] Started KNX Daemon. [ OK ] Started LSB: Advanced IEEE 802.11 management daemon. [ OK ] Started KNXD Configurator for Wiren Board. [ OK ] Stopped Wiren Board MQTT KNX bridge. [ OK ] Started Wiren Board MQTT KNX bridge. [ OK ] Stopped Kernel 1-Wire MQTT driver for WB-HomA. [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. [ OK ] Stopped Wiren Board MQTT to OPC UA gateway. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Stopped Wiren Board MQTT to Modbus TCP gateway. Starting Wiren Board MQTT to Modbus TCP gateway... Debian GNU/Linux 9 wirenboard-AXA7MZP5 ttyS0 wirenboard-AXA7MZP5 login: [ 34.403792] vcc-gmac-phy: disabling [ 34.407729] dc5ldo: disabling [ 34.411487] dldo4: disabling [ 34.421651] vcc-sd: disabling