=~=~=~=~=~=~=~=~=~=~=~= MobaXterm log 2026.08.24 13:55:14 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) DRAM init ok, rows:16, ncs:1, size: 1024MB .p0_mpdgctrl0= 0x010f0106 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3e3d .p0_mpwrdlctl= 0x3f3f3834 .p0_mpwldectrl0= 0x00070009 .p0_mpwldectrl1= 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 36C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 1 GiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl Error reading EEPROM #0: -19 Net: Could not get PHY for FEC0: addr 0 No ethernet found. Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ................................................ Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... Bus usb@2184000: USB EHCI 1.00 Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80 USB device not accepting new address (error=22) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot 322 bytes read in 2 ms (157.2 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 6304616 bytes read in 275 ms (21.9 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard690 47776 bytes read in 6 ms (7.6 MiB/s) 485 bytes read in 3 ms (157.2 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 4 ms (145.5 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 4 ms (124 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 4 ms (81.1 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 4 ms (61.5 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x82000000 [ 0x000000 - 0x603368 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to bef77000, end bef99fff ... OK Starting kernel ... U-Boot SPL 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) DRAM init ok, rows:16, ncs:1, size: 1024MB .p0_mpdgctrl0= 0x01110106 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3d3d .p0_mpwrdlctl= 0x3f3f3833 .p0_mpwldectrl0= 0x00070009 .p0_mpwldectrl1= 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 39C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 1 GiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl Error reading EEPROM #0: -19 Net: Could not get PHY for FEC0: addr 0 No ethernet found. Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ................................................ Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... Bus usb@2184000: USB EHCI 1.00 Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80 USB device not accepting new address (error=22) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot 322 bytes read in 2 ms (157.2 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 6304616 bytes read in 275 ms (21.9 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard690 47776 bytes read in 6 ms (7.6 MiB/s) 485 bytes read in 3 ms (157.2 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 4 ms (145.5 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 4 ms (124 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 4 ms (81.1 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 4 ms (61.5 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x82000000 [ 0x000000 - 0x603368 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to bef77000, end bef99fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb172 (root@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Wed Oct 16 09:17:25 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.9.0 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0xbf000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 259840 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1008652K/1048576K available (8192K kernel code, 728K rwdata, 2776K rodata, 1024K init, 283K bss, 23540K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x234/0x3dc with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000059] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002796] Console: colour dummy device 80x30 [ 0.002858] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002895] pid_max: default: 32768 minimum: 301 [ 0.003307] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.003348] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005075] CPU: Testing write buffer coherency: ok [ 0.006319] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.007324] devtmpfs: initialized [ 0.025285] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.025799] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025845] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.027223] pinctrl core: initialized pinctrl subsystem [ 0.029248] NET: Registered protocol family 16 [ 0.031558] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033549] thermal_sys: Registered thermal governor 'step_wise' [ 0.033837] cpuidle: using governor menu [ 0.221449] vdd1p1: supplied by regulator-dummy [ 0.233535] vdd3p0: supplied by regulator-dummy [ 0.245702] cpu: supplied by regulator-dummy [ 0.257859] vddsoc: supplied by regulator-dummy [ 0.600021] No ATAGs? [ 0.600083] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.600103] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.600714] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.601376] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.602850] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.602890] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.645679] mxs-dma 1804000.dma-apbh: initialized [ 0.650944] SCSI subsystem initialized [ 0.651436] usbcore: registered new interface driver usbfs [ 0.651564] usbcore: registered new interface driver hub [ 0.651678] usbcore: registered new device driver usb [ 0.652538] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.652665] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.654089] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.654991] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.655118] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.655708] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.656396] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.656517] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.657111] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.658710] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.659070] i2c i2c-1: IMX I2C adapter registered [ 0.659808] mc: Linux media interface: v0.10 [ 0.659916] videodev: Linux video capture interface: v2.00 [ 0.660044] pps_core: LinuxPPS API ver. 1 registered [ 0.660066] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.660117] PTP clock support registered [ 0.660731] Advanced Linux Sound Architecture Driver Initialized. [ 0.662896] clocksource: Switched to clocksource mxc_timer1 [ 0.680796] NET: Registered protocol family 2 [ 0.682078] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.682178] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.682358] TCP bind hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.682546] TCP: Hash tables configured (established 8192 bind 8192) [ 0.682769] UDP hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.682839] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.683334] NET: Registered protocol family 1 [ 0.684254] RPC: Registered named UNIX socket transport module. [ 0.684293] RPC: Registered udp transport module. [ 0.684311] RPC: Registered tcp transport module. [ 0.684326] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.685433] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.688251] Initialise system trusted keyrings [ 0.688713] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.700376] NFS: Registering the id_resolver key type [ 0.700452] Key type id_resolver registered [ 0.700471] Key type id_legacy registered [ 0.948869] Key type asymmetric registered [ 0.948910] Asymmetric key parser 'x509' registered [ 0.949033] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.949059] io scheduler mq-deadline registered [ 0.949076] io scheduler kyber registered [ 0.961011] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.961060] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.965062] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX [ 1.628094] printk: console [ttymxc0] enabled [ 1.634578] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX [ 1.678462] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.685897] random: fast init done [ 1.689851] random: crng init done [ 1.729974] brd: module loaded [ 1.748307] loop: module loaded [ 1.751823] at24 5-0050: supply vcc not found, using dummy regulator U-Boot SPL 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) DRAM init ok, rows:16, ncs:1, size: 1024MB .p0_mpdgctrl0= 0x010d0106 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3e3c .p0_mpwrdlctl= 0x3f3f3833 .p0_mpwldectrl0= 0x00080009 .p0_mpwldectrl1= 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 41C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 1 GiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl Error reading EEPROM #0: -19 Net: Could not get PHY for FEC0: addr 0 No ethernet found. Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ................................................ Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... Bus usb@2184000: USB EHCI 1.00 Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80 USB device not accepting new address (error=22) 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found No storage devices, perhaps not 'usb start'ed..? No USB update detected, continuing boot 322 bytes read in 2 ms (157.2 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 6304616 bytes read in 275 ms (21.9 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard690 47776 bytes read in 6 ms (7.6 MiB/s) 485 bytes read in 3 ms (157.2 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 4 ms (145.5 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 4 ms (124 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 4 ms (81.1 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 4 ms (61.5 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x82000000 [ 0x000000 - 0x603368 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to bef77000, end bef99fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb172 (root@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Wed Oct 16 09:17:25 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.9.0 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0xbf000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 259840 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1008652K/1048576K available (8192K kernel code, 728K rwdata, 2776K rodata, 1024K init, 283K bss, 23540K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x234/0x3dc with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000059] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002803] Console: colour dummy device 80x30 [ 0.002868] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002907] pid_max: default: 32768 minimum: 301 [ 0.003320] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.003363] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005092] CPU: Testing write buffer coherency: ok [ 0.006331] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.007341] devtmpfs: initialized [ 0.025290] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.025801] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025847] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.027230] pinctrl core: initialized pinctrl subsystem [ 0.029253] NET: Registered protocol family 16 [ 0.031558] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033572] thermal_sys: Registered thermal governor 'step_wise' [ 0.033862] cpuidle: using governor menu [ 0.221406] vdd1p1: supplied by regulator-dummy [ 0.233569] vdd3p0: supplied by regulator-dummy [ 0.245683] cpu: supplied by regulator-dummy [ 0.257811] vddsoc: supplied by regulator-dummy [ 0.599861] No ATAGs? [ 0.599922] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.599943] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.600554] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.601226] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.602702] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.602745] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.645615] mxs-dma 1804000.dma-apbh: initialized [ 0.650886] SCSI subsystem initialized [ 0.651363] usbcore: registered new interface driver usbfs [ 0.651487] usbcore: registered new interface driver hub [ 0.651601] usbcore: registered new device driver usb [ 0.652454] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.652581] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.654010] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.654906] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.655032] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.655615] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.656310] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.656437] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.657031] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.658630] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.658993] i2c i2c-1: IMX I2C adapter registered [ 0.659722] mc: Linux media interface: v0.10 [ 0.659830] videodev: Linux video capture interface: v2.00 [ 0.659958] pps_core: LinuxPPS API ver. 1 registered [ 0.659978] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.660032] PTP clock support registered [ 0.660647] Advanced Linux Sound Architecture Driver Initialized. [ 0.662833] clocksource: Switched to clocksource mxc_timer1 [ 0.680755] NET: Registered protocol family 2 [ 0.682051] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.682151] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.682328] TCP bind hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.682516] TCP: Hash tables configured (established 8192 bind 8192) [ 0.682739] UDP hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.682900] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.683312] NET: Registered protocol family 1 [ 0.684240] RPC: Registered named UNIX socket transport module. [ 0.684275] RPC: Registered udp transport module. [ 0.684293] RPC: Registered tcp transport module. [ 0.684308] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.685411] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.688226] Initialise system trusted keyrings [ 0.688688] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.700371] NFS: Registering the id_resolver key type [ 0.700451] Key type id_resolver registered [ 0.700471] Key type id_legacy registered [ 0.941580] Key type asymmetric registered [ 0.941619] Asymmetric key parser 'x509' registered [ 0.941742] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.941764] io scheduler mq-deadline registered [ 0.941781] io scheduler kyber registered [ 0.953947] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.953996] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.957892] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX [ 1.620931] printk: console [ttymxc0] enabled [ 1.627425] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX [ 1.671221] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.678648] random: fast init done [ 1.682603] random: crng init done [ 1.722652] brd: module loaded [ 1.740977] loop: module loaded [ 1.744589] at24 5-0050: supply vcc not found, using dummy regulator U-Boot SPL 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) DRAM init ok, rows:16, ncs:1, size: 1024MB .p0_mpdgctrl0= 0x01100106 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3e3d .p0_mpwrdlctl= 0x3f3f3834 .p0_mpwldectrl0= 0x00090009 .p0_mpwldectrl1= 0x000a000a Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-g1c43ce9a10 (Jul 30 2024 - 18:15:12 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 41C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 1 GiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl timeout waiting on slave to release scl