▒......... Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ## Loading FIT strings to 0x42000028 ... ## Loading FIT struct to 0x42000100 ... Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x42000000 ... ## Loading FIT strings to 0x42000028 ... ## Loading FIT struct to 0x42000100 ... 7770848 bytes read in 229 ms (32.4 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x42000300 Data Size: 7761888 Bytes = 7.4 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 58eb2949fba68971ec9b6f42197daab785109ac1 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x43000000 ... ## Loading FIT strings to 0x43000028 ... ## Loading FIT struct to 0x43000100 ... 63880 bytes read in 26 ms (2.3 MiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x43000540 Data Size: 54344 Bytes = 53.1 KiB Architecture: ARM Hash algo: sha1 Hash value: 88cb690e62d3e2fbe97df37350c2ee8c8abab757 ## Verifying ... sha1+ Loading part 0 ... OK Kernel image @ 0x42000000 [ 0x000000 - 0x766fe0 ] ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Device Tree to 49fef000, end 49fff447 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35+ (webconn@webconn-laptop) (arm-linux-gnueab ihf-gcc (Debian 10.3.0-8) 10.3.0, GNU ld (GNU Binutils for Debian) 2.37.90.20220 123) #6 SMP Wed Feb 9 22:20:01 MSK 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 7.2.0 (A40i) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x7ec00000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 15 pages/cpu s31180 r8192 d22068 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 bootmode=update_auto [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, li near) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1007360K/1048576K available (7168K kernel code, 657K rwda ta, 1524K rodata, 4096K init, 398K bss, 24832K reserved, 16384K cma-reserved, 24 5748K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x4f8 wit h crng_init=0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_ idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000011] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns [ 0.000031] Switching to timer-based delay loop, resolution 41ns [ 0.000458] Console: colour dummy device 80x30 [ 0.000526] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=240000) [ 0.000555] pid_max: default: 32768 minimum: 301 [ 0.000771] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linea r) [ 0.000794] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001847] CPU: Testing write buffer coherency: ok [ 0.002200] /cpus/cpu@0 missing clock-frequency property [ 0.002229] /cpus/cpu@1 missing clock-frequency property [ 0.002253] /cpus/cpu@2 missing clock-frequency property [ 0.002278] /cpus/cpu@3 missing clock-frequency property [ 0.002291] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.003550] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.003933] rcu: Hierarchical SRCU implementation. [ 0.005121] smp: Bringing up secondary CPUs ... [ 0.016202] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.027370] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.038417] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.038563] smp: Brought up 1 node, 4 CPUs [ 0.038599] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.038611] CPU: All CPU(s) started in HYP mode. [ 0.038620] CPU: Virtualization extensions available. [ 0.039443] devtmpfs: initialized [ 0.056946] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.057203] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.057229] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.059672] pinctrl core: initialized pinctrl subsystem [ 0.061088] NET: Registered protocol family 16 [ 0.062230] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.064590] thermal_sys: Registered thermal governor 'step_wise' [ 0.065445] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.065473] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.117307] SCSI subsystem initialized [ 0.118330] usbcore: registered new interface driver usbfs [ 0.118506] usbcore: registered new interface driver hub [ 0.118655] usbcore: registered new device driver usb [ 0.121294] clocksource: Switched to clocksource arch_sys_counter [ 0.121701] FS-Cache: Loaded [ 0.121988] CacheFiles: Loaded [ 0.136255] NET: Registered protocol family 2 [ 0.137098] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.137164] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.137269] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.137435] TCP: Hash tables configured (established 8192 bind 8192) [ 0.137587] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.137664] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.137905] NET: Registered protocol family 1 [ 0.138741] RPC: Registered named UNIX socket transport module. [ 0.138762] RPC: Registered udp transport module. [ 0.138770] RPC: Registered tcp transport module. [ 0.138778] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.436807] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counter s available [ 0.438658] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.452731] NFS: Registering the id_resolver key type [ 0.452815] Key type id_resolver registered [ 0.452831] Key type id_legacy registered [ 0.452908] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.453892] bounce: pool size: 64 pages [ 0.453960] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 50) [ 0.453976] io scheduler mq-deadline registered [ 0.453987] io scheduler kyber registered [ 0.454738] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 0.577897] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.597068] loop: module loaded [ 0.608420] libphy: Fixed MDIO Bus: probed [ 0.608854] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 0.610812] libphy: sun4i_mii_bus: probed [ 0.613667] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.613687] ehci-platform: EHCI generic platform driver [ 0.614260] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.614288] ohci-platform: OHCI generic platform driver [ 0.616163] usbcore: registered new interface driver cdc_acm [ 0.616185] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters [ 0.616303] usbcore: registered new interface driver usb-storage [ 0.618808] sun6i-rtc 1c20400.rtc: registered as rtc1 [ 0.618827] sun6i-rtc 1c20400.rtc: RTC enabled [ 0.619106] i2c /dev entries driver [ 0.623968] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, now ayout=0) [ 0.626885] ledtrig-cpu: registered to indicate activity on CPUs [ 0.627623] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) fro m 24000000 (24 Mhz) [ 0.628056] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 0.628679] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 0.628868] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 0.629033] sun8i-ce 1c15000.crypto: will run requests pump with realtime pri ority [ 0.629174] sun8i-ce 1c15000.crypto: Register cbc(aes) [ 0.629353] sun8i-ce 1c15000.crypto: Register ecb(aes) [ 0.629495] sun8i-ce 1c15000.crypto: Register cbc(des3_ede) [ 0.629627] sun8i-ce 1c15000.crypto: Register ecb(des3_ede) [ 0.629779] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0 [ 0.633026] iio-rescale a1-volt: using raw+scale source channel [ 0.633505] iio-rescale a2-volt: using raw+scale source channel [ 0.633865] iio-rescale a3-volt: using raw+scale source channel [ 0.634199] iio-rescale vin-volt: using raw+scale source channel [ 0.636349] NET: Registered protocol family 10 [ 0.638545] Segment Routing with IPv6 [ 0.638681] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 0.639638] NET: Registered protocol family 17 [ 0.639761] Key type dns_resolver registered [ 0.639832] Registering SWP/SWPB emulation handler [ 0.639931] registered taskstats version 1 [ 0.663406] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 0.669557] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.670696] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dum my regulator [ 0.672947] printk: console [ttyS0] disabled [ 0.673083] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 52, base_baud = 15 00000) is a Allwinner sun4i [ 1.524284] printk: console [ttyS0] enabled [ 1.529593] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PI regulator [ 1.536440] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 274 [ 1.543289] sun4i-pinctrl 1c20800.pinctrl: pin-274 (1c28800.serial) status -5 17 [ 1.550633] sun4i-pinctrl 1c20800.pinctrl: could not request pin 274 (PI18) f rom group PI18 on device 1c20800.pinctrl [ 1.561355] dw-apb-uart 1c28800.serial: Error applying setting, reverse thing s back [ 1.569424] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 1.578058] libphy: sun4i_mii_bus: probed [ 1.583400] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 1.590200] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 236 [ 1.596840] sun4i-pinctrl 1c20800.pinctrl: pin-236 (1c20800.pinctrl:236) stat us -517 [ 1.606489] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 1.613300] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 232 [ 1.619943] sun4i-pinctrl 1c20800.pinctrl: pin-232 (1c0b000.ethernet) status -517 [ 1.627469] sun4i-pinctrl 1c20800.pinctrl: could not request pin 232 (PH8) fr om group PH8 on device 1c20800.pinctrl [ 1.638005] sun4i-emac 1c0b000.ethernet: Error applying setting, reverse thin gs back [ 1.646150] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 1.653041] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 1.659501] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -5 17 [ 1.666824] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 1.677177] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse thi ngs back [ 1.697921] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 1.712088] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-00 34/axp221-pek/input/input0 [ 1.732800] vcc-3v3: supplied by regulator-dummy [ 1.738226] vdd-cpu: supplied by regulator-dummy [ 1.743651] vdd-sys: supplied by regulator-dummy [ 1.749018] dcdc4: supplied by regulator-dummy [ 1.754289] vcc-dram: supplied by regulator-dummy [ 1.759108] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER [ 1.766035] vcc-gmac-phy: supplied by vcc-3v3 [ 1.771301] dc5ldo: supplied by vcc-dram [ 1.775397] random: fast init done [ 1.779170] tv: Bringing 700000uV into 3300000-3300000uV [ 1.785272] tv: supplied by regulator-dummy [ 1.790202] aldo2: Bringing 2500000uV into 3300000-3300000uV [ 1.796571] aldo2: supplied by regulator-dummy [ 1.802444] avcc-pll: supplied by regulator-dummy [ 1.808008] eldo1: supplied by regulator-dummy [ 1.813415] eldo2: supplied by regulator-dummy [ 1.818505] vcc-pe: Bringing 1200000uV into 1800000-1800000uV [ 1.825254] vcc-pe: supplied by regulator-dummy [ 1.830344] vcc-sd-alt: Bringing 700000uV into 1800000-1800000uV [ 1.837193] vcc-sd-alt: supplied by regulator-dummy [ 1.842810] dldo2: supplied by regulator-dummy [ 1.847965] dldo3: supplied by regulator-dummy [ 1.853187] dldo4: supplied by regulator-dummy [ 1.857953] rtc_ldo: supplied by regulator-dummy [ 1.863375] ldo_io0: supplied by regulator-dummy [ 1.868739] ldo_io1: supplied by regulator-dummy [ 1.879574] axp20x-adc axp22x-adc: DMA mask not set [ 1.885814] axp20x-i2c 0-0034: AXP20X driver loaded [ 1.922097] rtc-pcf85063 2-0051: registered as rtc0 [ 1.936625] rtc-pcf85063 2-0051: setting system clock to 2023-03-28T12:32:01 UTC (1680006721) [ 1.951082] lm75 2-0048: supply vs not found, using dummy regulator [ 1.961769] lm75 2-0048: hwmon0: sensor 'lm75b' [ 1.992632] at24 3-0050: supply vcc not found, using dummy regulator [ 2.000280] at24 3-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 2.014233] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, u ses new timings mode [ 2.104316] i2c-gpio i2c_eeprom1: using lines 48 (SDA) and 49 (SCL) [ 2.114056] at24 4-0050: supply vcc not found, using dummy regulator [ 2.137076] mmc0: new DDR MMC card at address 0001 [ 2.142584] mmcblk0: mmc0:0001 008GB0 7.28 GiB [ 2.147438] mmcblk0boot0: mmc0:0001 008GB0 partition 1 8.00 MiB [ 2.153737] mmcblk0boot1: mmc0:0001 008GB0 partition 2 8.00 MiB [ 2.154305] i2c-gpio i2c_eeprom2: using lines 46 (SDA) and 47 (SCL) [ 2.159950] mmcblk0rpmb: mmc0:0001 008GB0 partition 3 4.00 MiB, chardev (248: 0) [ 2.166328] sun4i-usb-phy 1c13400.phy: phy0 dr_mode=3 [ 2.180736] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 53, base_baud = 15 00000) is a Allwinner sun4i [ 2.190956] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regula tor [ 2.198887] libphy: sun4i_mii_bus: probed [ 2.203148] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 2.342435] sun4i-emac 1c0b000.ethernet: using random MAC address de:4e:ff:12 :d6:7f [ 2.352124] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 65 MAC: de:4e :ff:12:d6:7f [ 2.360969] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 2.367369] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 2.375775] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 2.381860] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supporte d [ 2.389081] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supporte d [ 2.396319] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 2.401297] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 2.408094] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 2.413761] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 2.419422] dwmac-sun8i 1c50000.ethernet: device MAC address aa:8a:13:8b:0c:8 e [ 2.427213] libphy: stmmac: probed [ 2.693250] ehci-platform 1c14000.usb: EHCI Host Controller [ 2.698849] ehci-platform 1c14000.usb: new USB bus registered, assigned bus n umber 1 [ 2.706926] ehci-platform 1c14000.usb: irq 37, io mem 0x01c14000 [ 2.741286] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 2.748119] hub 1-0:1.0: USB hub found [ 2.751942] hub 1-0:1.0: 1 port detected [ 2.756701] ehci-platform 1c19000.usb: EHCI Host Controller [ 2.762317] ehci-platform 1c19000.usb: new USB bus registered, assigned bus n umber 2 [ 2.770240] ehci-platform 1c19000.usb: irq 39, io mem 0x01c19000 [ 2.801288] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 2.808034] hub 2-0:1.0: USB hub found [ 2.811829] hub 2-0:1.0: 1 port detected [ 2.816513] ehci-platform 1c1c000.usb: EHCI Host Controller [ 2.822118] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus n umber 3 [ 2.830028] ehci-platform 1c1c000.usb: irq 41, io mem 0x01c1c000 [ 2.861983] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 2.868679] hub 3-0:1.0: USB hub found [ 2.872477] hub 3-0:1.0: 1 port detected [ 2.971358] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 2.977986] ohci-platform 1c14400.usb: new USB bus registered, assigned bus n umber 4 [ 2.985912] ohci-platform 1c14400.usb: irq 38, io mem 0x01c14400 [ 3.065904] hub 4-0:1.0: USB hub found [ 3.069687] hub 4-0:1.0: 1 port detected [ 3.074385] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 3.081008] ohci-platform 1c19400.usb: new USB bus registered, assigned bus n umber 5 [ 3.088903] ohci-platform 1c19400.usb: irq 40, io mem 0x01c19400 [ 3.165915] hub 5-0:1.0: USB hub found [ 3.169696] hub 5-0:1.0: 1 port detected [ 3.174384] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 3.181009] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus n umber 6 [ 3.188814] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 3.196006] ohci-platform 1c1c400.usb: irq 42, io mem 0x01c1c400 [ 3.275914] hub 6-0:1.0: USB hub found [ 3.279697] hub 6-0:1.0: 1 port detected [ 3.284667] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, usi ng dummy regulator [ 3.294790] of_cfs_init [ 3.295890] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 3.297288] of_cfs_init: OK [ 3.327044] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 3.340612] Freeing unused kernel memory: 4096K [ 3.401517] Run /init as init process mount: mounting none on /dev/pts failed: No such file or directory Boot mode: update_auto Board is WB7 Checking that no-one is using this disk right now ... OK[ 4.899824] random: s fdisk: uninitialized urandom read (4 bytes read) Disk /tmp/ramdisk.img: 300 MiB, 314572800 bytes, 614400 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes >>> Created a new DOS disklabel with disk identifier 0x320c9977. /tmp/ramdisk.img1: Created a new partition 1 of type 'W95 FAT32' and of size 299 MiB. /tmp/ramdisk.img2: Done. New situation: Device Boot Start End Sectors Size Id Type /tmp/ramdisk.img1 2048 614399 612352 299M b W95 FAT32 The partition table has been altered. Syncing disks. mkfs.fat 4.1 (2017-01-24) [ 5.056232] random: mkfs.vfat: uninitialized urandom read (16 bytes read) Activate Mass Storage device [ 5.266996] Mass Storage Function, version: 2009/09/11 [ 5.272223] LUN: removable file: (no medium) [ 5.276613] LUN: file: /tmp/ramdisk.img [ 5.280447] Number of LUNs=1 [ 5.283511] g_mass_storage gadget: Mass Storage Gadget, version: 2009/09/11 [ 5.290468] g_mass_storage gadget: userspace failed to provide iSerialNumber [ 5.297531] g_mass_storage gadget: g_mass_storage ready [ 5.307797] phy phy-1c13400.phy.0: Changing dr_mode to 1 Load modules for USB to work Waiting for USB to settle (10/10) Waiting for microSD to settle (3/3) Wait for eMMC to become available... Will use /mnt/data/.wb-restore/factoryreset.fit [ 18.393759] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. O pts: (null) ############################################################################## FACTORY RESET REQUESTED This WILL destroy ALL YOUR DATA: configuration, scripts, files in home directory! If you are ABSOLUTELY SURE that you want to reset Wiren Board to factory condition, hold the FW button for 4 seconds. If you will not do it in 10 seconds, the controller will reboot without firmware update. If you want to perform a regular firmware update, rename FIT file to "wbX_update.fit" without "factory-reset" suffix. ############################################################################## .... Factory reset is confirmed! =============================================================================== Tue Mar 28 12:32:23 UTC 2023: started update from /mnt/data/.wb-restore/factoryr eset.fit =============================================================================== Description: WirenBoard firmware update Compatible device: wirenboard,wirenboard-720 Firmware version: 202212201339 Firmware compatible: unknown Release name: wb-2207 Release suite: stable Release target: wb7/stretch Release repo prefix: Time of creation: Tue Dec 20 13:40:24 UTC 2022 =============================================================================== >>> Checking SHA1 hash of install PROGRESS: 0% >>> SHA1 hash of install ok >>> Wiping data partition (factory reset) mount: mounting /dev/mmcblk0p6 on /mnt/data failed: Device or resource busy >>> Extracting install script >>> Running install script >>> Checking SHA1 hash of rootfs PROGRESS: 100% >>> SHA1 hash of rootfs ok >>> Installing firmware update >>> Getting mmcpart from U-Boot environment >>> Will install to /dev/mmcblk0p2 >>> Check if partition table is correct [ 33.672382] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) >>> Mounting /dev/mmcblk0p2 at /dev/shm/rootfs [ 33.699197] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) >>> Cleaning up /dev/mmcblk0p2 >>> Cleaning up using rsync [ 33.771361] vcc-gmac-phy: disabling [ 33.775229] dc5ldo: disabling [ 33.778541] dldo4: disabling [ 33.781764] vcc-sd: disabling [ 38.886803] random: crng init done >>> Extracting files to new rootfs /dev/shm/rootfs / PROGRESS: 100% / >>> Recovering device certificates [ 65.933752] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null) >>> Mount /dev, /proc and /sys to rootfs >>> Running post-install scripts >>> > Processing /dev/shm/rootfs/usr/lib/wb-image-update/postinst/10update-u-boot Trying to install u-boot using u-boot-install-wb from new rootfs Das U-Boot installer for Wiren Board You are about to install U-boot image '/usr/lib/u-boot/sun8i_wirenboard7/u-boot-sunxi-with-spl.bin' on '/dev/mmcblk0' (platform wb7) Force installation requested Writing U-boot image '/usr/lib/u-boot/sun8i_wirenboard7/u-boot-sunxi-with-spl.bin' on '/dev/mmcblk0' (options 'bs=1024 seek=8') 450+1 records in 450+1 records out 461708 bytes (462 kB, 451 KiB) copied, 0.0527037 s, 8.8 MB/s Syncing device >>> Unmounting /dev, /proc and /sys from rootfs >>> Unmounting new rootfs >>> Switching to new rootfs >>> Done! >>> Reboot system [ 70.064052] reboot: Restarting system [ 70.077767] i2c i2c-0: No atomic I2C transfer handler U-Boot SPL 2021.10-wb1.4.4-g8b6bef383e (Nov 24 2022 - 14:01:43 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.4.4-g8b6bef383e (Nov 24 2022 - 14:01:43 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 142 = 0x8E bootcount=0 mmcpart=2 uenvcmd=true ; echo reset environment; env default -a; setenv mmcdev 0; saveenv; bmode emmc; reset upgrade_available=1 Environment size: 142/131068 bytes ## Resetting to default environment ## Info: input data size = 142 = 0x8E Net: No ethernet found. Hit key to stop autoboot in 1s switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ................................................ 326 bytes read in 1 ms (318.4 KiB/s) Importing environment from 0x42000000... Checking if uenvcmd is set ... test - minimal test like /bin/sh Usage: test [args..] Running default loadzimage ... 6042192 bytes read in 163 ms (35.4 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt sun8i-r40-wirenboard733 54704 bytes read in 5 ms (10.4 MiB/s) 254 bytes read in 3 ms (82 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x42000000 [ 0x000000 - 0x5c3250 ] ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Device Tree to 49fdd000, end 49ffffff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb120+wb101 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #2 SMP Tue Nov 22 12:49:35 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 7.3.3 (A40i) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x7ec00000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 19 pages/cpu s47884 r8192 d21748 u77824 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1006628K/1048576K available (9216K kernel code, 1430K rwdata, 3068K rodata, 1024K init, 293K bss, 25564K reserved, 16384K cma-reserved, 245748K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 29913 entries in 59 pages [ 0.000000] ftrace: allocated 59 pages with 5 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x660/0x840 with crng_init=0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000011] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000034] Switching to timer-based delay loop, resolution 41ns [ 0.000506] Console: colour dummy device 80x30 [ 0.000596] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000638] pid_max: default: 32768 minimum: 301 [ 0.000919] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.000954] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002186] CPU: Testing write buffer coherency: ok [ 0.002625] /cpus/cpu@0 missing clock-frequency property [ 0.002676] /cpus/cpu@1 missing clock-frequency property [ 0.002722] /cpus/cpu@2 missing clock-frequency property [ 0.002770] /cpus/cpu@3 missing clock-frequency property [ 0.002788] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005432] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.005744] rcu: Hierarchical SRCU implementation. [ 0.006897] smp: Bringing up secondary CPUs ... [ 0.018112] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.029473] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.042010] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.042547] smp: Brought up 1 node, 4 CPUs [ 0.042634] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.042665] CPU: All CPU(s) started in HYP mode. [ 0.042694] CPU: Virtualization extensions available. [ 0.044207] devtmpfs: initialized [ 0.066635] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.067012] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.067053] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.068123] pinctrl core: initialized pinctrl subsystem [ 0.071404] NET: Registered protocol family 16 [ 0.075814] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.077742] thermal_sys: Registered thermal governor 'step_wise' [ 0.078306] No ATAGs? [ 0.078553] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.078571] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.161479] SCSI subsystem initialized [ 0.162685] usbcore: registered new interface driver usbfs [ 0.162846] usbcore: registered new interface driver hub [ 0.163005] usbcore: registered new device driver usb [ 0.163705] mc: Linux media interface: v0.10 [ 0.163797] videodev: Linux video capture interface: v2.00 [ 0.163900] pps_core: LinuxPPS API ver. 1 registered [ 0.163924] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.163989] PTP clock support registered [ 0.164462] Advanced Linux Sound Architecture Driver Initialized. [ 0.165777] clocksource: Switched to clocksource arch_sys_counter [ 1.354160] NET: Registered protocol family 2 [ 1.355219] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.355296] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.355412] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.355579] TCP: Hash tables configured (established 8192 bind 8192) [ 1.355834] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.355922] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.356265] NET: Registered protocol family 1 [ 1.358582] RPC: Registered named UNIX socket transport module. [ 1.358642] RPC: Registered udp transport module. [ 1.358677] RPC: Registered tcp transport module. [ 1.358709] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.361233] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 1.364119] Initialise system trusted keyrings [ 1.364649] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 1.378995] NFS: Registering the id_resolver key type [ 1.379074] Key type id_resolver registered [ 1.379310] Key type id_legacy registered [ 1.381021] Key type asymmetric registered [ 1.381061] Asymmetric key parser 'x509' registered [ 1.381343] bounce: pool size: 64 pages [ 1.381441] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.381471] io scheduler mq-deadline registered [ 1.381496] io scheduler kyber registered [ 1.383072] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.534454] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.558829] brd: module loaded [ 1.578244] loop: module loaded [ 1.587977] libphy: Fixed MDIO Bus: probed [ 1.590098] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 1.590937] libphy: sun4i_mii_bus: probed [ 1.594827] CAN device driver interface [ 1.597442] PPP generic driver version 2.4.2 [ 1.598477] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.598537] ehci-platform: EHCI generic platform driver [ 1.600611] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.600664] ohci-platform: OHCI generic platform driver [ 1.602061] usbcore: registered new interface driver usb-storage [ 1.602193] usbcore: registered new interface driver usbserial_generic [ 1.602239] usbserial: USB Serial support registered for generic [ 1.606506] sun6i-rtc 1c20400.rtc: registered as rtc1 [ 1.606537] sun6i-rtc 1c20400.rtc: RTC enabled [ 1.607034] i2c /dev entries driver [ 1.617986] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.623313] ledtrig-cpu: registered to indicate activity on CPUs [ 1.624063] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) from 24000000 (24 Mhz) [ 1.624435] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.625548] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.626519] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.626967] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.627256] sun8i-ce 1c15000.crypto: Register cbc(aes) [ 1.627603] sun8i-ce 1c15000.crypto: Register ecb(aes) [ 1.627897] sun8i-ce 1c15000.crypto: Register cbc(des3_ede) [ 1.628183] sun8i-ce 1c15000.crypto: Register ecb(des3_ede) [ 1.628471] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0 [ 1.631507] usbcore: registered new interface driver usbhid [ 1.631556] usbhid: USB HID core driver [ 1.635456] iio-rescale a1-volt: using raw+scale source channel [ 1.636758] iio-rescale a2-volt: using raw+scale source channel [ 1.637680] iio-rescale a3-volt: using raw+scale source channel [ 1.638326] iio-rescale vin-volt: using raw+scale source channel [ 1.644218] NET: Registered protocol family 10 [ 1.645590] Segment Routing with IPv6 [ 1.645694] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.646627] NET: Registered protocol family 17 [ 1.646660] can: controller area network core [ 1.647353] NET: Registered protocol family 29 [ 1.647422] can: raw protocol [ 1.647482] can: broadcast manager protocol [ 1.647561] can: netlink gateway - max_hops=1 [ 1.648221] Key type dns_resolver registered [ 1.648387] Registering SWP/SWPB emulation handler [ 1.648618] registered taskstats version 1 [ 1.648723] Loading compiled-in X.509 certificates [ 1.683195] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.690241] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 1.692567] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator [ 1.700380] printk: console [ttyS0] disabled [ 1.700559] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 52, base_baud = 1500000) is a Allwinner sun4i [ 2.658758] printk: console [ttyS0] enabled [ 2.665250] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PI regulator [ 2.672096] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 274 [ 2.678746] sun4i-pinctrl 1c20800.pinctrl: pin-274 (1c28800.serial) status -517 [ 2.686108] sun4i-pinctrl 1c20800.pinctrl: could not request pin 274 (PI18) from group PI18 on device 1c20800.pinctrl [ 2.696857] dw-apb-uart 1c28800.serial: Error applying setting, reverse things back [ 2.705366] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 2.714235] libphy: sun4i_mii_bus: probed [ 2.720021] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.726872] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 236 [ 2.733567] sun4i-pinctrl 1c20800.pinctrl: pin-236 (1c20800.pinctrl:236) status -517 [ 2.743809] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.750722] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 232 [ 2.757414] sun4i-pinctrl 1c20800.pinctrl: pin-232 (1c0b000.ethernet) status -517 [ 2.764910] sun4i-pinctrl 1c20800.pinctrl: could not request pin 232 (PH8) from group PH8 on device 1c20800.pinctrl [ 2.775445] sun4i-emac 1c0b000.ethernet: Error applying setting, reverse things back [ 2.785047] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 2.791872] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 2.798331] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -517 [ 2.805665] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 2.816121] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse things back [ 2.835871] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 2.850140] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0034/axp221-pek/input/input0 [ 2.873496] vcc-3v3: supplied by regulator-dummy [ 2.879345] vdd-cpu: supplied by regulator-dummy [ 2.885042] vdd-sys: supplied by regulator-dummy [ 2.890775] dcdc4: supplied by regulator-dummy [ 2.896287] vcc-dram: supplied by regulator-dummy [ 2.901218] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER [ 2.908426] vcc-gmac-phy: supplied by vcc-3v3 [ 2.915157] dc5ldo: supplied by vcc-dram [ 2.920550] tv: Bringing 700000uV into 3300000-3300000uV [ 2.927093] tv: supplied by regulator-dummy [ 2.932237] aldo2: Bringing 2500000uV into 3300000-3300000uV [ 2.938825] aldo2: supplied by regulator-dummy [ 2.944924] avcc-pll: supplied by regulator-dummy [ 2.950229] random: fast init done [ 2.954393] eldo1: supplied by regulator-dummy [ 2.960404] eldo2: supplied by regulator-dummy [ 2.965716] vcc-pe: Bringing 1200000uV into 1800000-1800000uV [ 2.972726] vcc-pe: supplied by regulator-dummy [ 2.977967] vcc-sd-alt: Bringing 700000uV into 1800000-1800000uV [ 2.986218] vcc-sd-alt: supplied by regulator-dummy [ 2.992851] dldo2: supplied by regulator-dummy [ 2.998777] dldo3: supplied by regulator-dummy [ 3.004513] dldo4: supplied by regulator-dummy [ 3.009893] rtc_ldo: supplied by regulator-dummy [ 3.015661] ldo_io0: supplied by regulator-dummy [ 3.021456] ldo_io1: supplied by regulator-dummy [ 3.027094] axp20x-adc axp22x-adc: DMA mask not set [ 3.034288] axp20x-battery-power-supply axp20x-battery-power-supply: DMA mask not set [ 3.044681] axp20x-i2c 0-0034: AXP20X driver loaded [ 3.078780] rtc-pcf85063 2-0051: registered as rtc0 [ 3.093192] rtc-pcf85063 2-0051: setting system clock to 2023-03-28T12:33:22 UTC (1680006802) [ 3.102606] lm75 2-0048: supply vs not found, using dummy regulator [ 3.113515] lm75 2-0048: hwmon1: sensor 'lm75b' [ 3.152400] sun4i-usb-phy 1c13400.phy: phy0 dr_mode=3 [ 3.161012] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 53, base_baud = 1500000) is a Allwinner sun4i [ 3.171449] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 3.179441] libphy: sun4i_mii_bus: probed [ 3.185832] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, uses new timings mode [ 3.318492] mmc0: new DDR MMC card at address 0001 [ 3.319279] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 65 MAC: 00:85:01:01:0b:5f [ 3.324162] mmcblk0: mmc0:0001 008GB0 7.28 GiB [ 3.332559] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 3.336470] mmcblk0boot0: mmc0:0001 008GB0 partition 1 8.00 MiB [ 3.342450] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 3.348788] mmcblk0boot1: mmc0:0001 008GB0 partition 2 8.00 MiB [ 3.354792] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 3.360556] mmcblk0rpmb: mmc0:0001 008GB0 partition 3 4.00 MiB, chardev (246:0) [ 3.366420] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supported [ 3.380608] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supported [ 3.387892] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 3.392859] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 3.399663] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 3.405321] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 3.411689] libphy: stmmac: probed [ 3.416831] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 3.678525] ehci-platform 1c14000.usb: EHCI Host Controller [ 3.684141] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 3.692318] ehci-platform 1c14000.usb: irq 37, io mem 0x01c14000 [ 3.725771] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 3.732899] hub 1-0:1.0: USB hub found [ 3.736767] hub 1-0:1.0: 1 port detected [ 3.741927] ehci-platform 1c19000.usb: EHCI Host Controller [ 3.747554] ehci-platform 1c19000.usb: new USB bus registered, assigned bus number 2 [ 3.755552] ehci-platform 1c19000.usb: irq 39, io mem 0x01c19000 [ 3.785769] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 3.792781] hub 2-0:1.0: USB hub found [ 3.796612] hub 2-0:1.0: 1 port detected [ 3.801697] ehci-platform 1c1c000.usb: EHCI Host Controller [ 3.807317] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 3 [ 3.815309] ehci-platform 1c1c000.usb: irq 41, io mem 0x01c1c000 [ 3.846399] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 3.853351] hub 3-0:1.0: USB hub found [ 3.857177] hub 3-0:1.0: 1 port detected [ 3.955861] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 3.962498] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 4 [ 3.970464] ohci-platform 1c14400.usb: irq 38, io mem 0x01c14400 [ 4.050638] hub 4-0:1.0: USB hub found [ 4.054454] hub 4-0:1.0: 1 port detected [ 4.059575] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 4.066255] ohci-platform 1c19400.usb: new USB bus registered, assigned bus number 5 [ 4.074272] ohci-platform 1c19400.usb: irq 40, io mem 0x01c19400 [ 4.150691] hub 5-0:1.0: USB hub found [ 4.154498] hub 5-0:1.0: 1 port detected [ 4.159620] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 4.166294] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 6 [ 4.174087] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 4.181364] ohci-platform 1c1c400.usb: irq 42, io mem 0x01c1c400 [ 4.260705] hub 6-0:1.0: USB hub found [ 4.264515] hub 6-0:1.0: 1 port detected [ 4.270607] of_cfs_init [ 4.271945] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 4.273181] of_cfs_init: OK [ 4.284947] ALSA device list: [ 4.287981] No soundcards found. [ 4.302979] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 4.319502] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 4.327731] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 4.338827] devtmpfs: mounted [ 4.346477] Freeing unused kernel memory: 1024K [ 4.376091] Run /sbin/init as init process [ 4.544558] random: systemd: uninitialized urandom read (16 bytes read) [ 4.556840] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 4.577089] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 4.617270] systemd[1]: Set hostname to . [ 4.644234] random: systemd: uninitialized urandom read (16 bytes read) [ 4.682136] random: systemd-cryptse: uninitialized urandom read (16 bytes read) [ 4.867800] systemd[1]: [/lib/systemd/system/wb-mqtt-w1.service:10] Unknown lvalue 'StartLimitIntervalSec' in section 'Service' [ 4.925991] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 4.966769] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 5.006311] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 5.056128] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 5.096323] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 5.136040] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ OK ] Listening on fsck to fsckd communication Socket. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. Starting File System Check on Root Device... [ OK ] Created slice system-systemd\x2dfsck.slice. Mounting POSIX Message Queue File System... Starting Load Kernel Modules... Mounting Debug File System... Mounting /sys/kernel/config... [ OK ] Listening on Journal Socket (/dev/log). Starting Create list of required st…ce nodes for the current kernel... [ OK ] Listening on Syslog Socket. Starting Journal Service... [ OK ] Created slice system-getty.slice. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Reached target Slices. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted /sys/kernel/config. [ OK ] Started Journal Service. [ OK ] Started File System Check on Root Device. [ OK ] Started Load Kernel Modules. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started File System Check Daemon to report status. Starting Create Static Device Nodes in /dev... Starting Apply Kernel Variables... Starting Remount Root and Kernel File Systems... [ 6.069616] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting prepare partitions at first boot... Starting udev Coldplug all Devices... Starting udev Kernel Device Manager... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started prepare partitions at first boot. [ OK ] Reached target Local File Systems (Pre). [ 6.893785] Driver for 1-wire Dallas network protocol. [ OK ] Started udev Coldplug all Devices. [ 7.053931] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator [ OK ] Found device /dev/ttyS0. [ 7.135410] Bluetooth: Core ver 2.22 [ 7.139308] NET: Registered protocol family 31 [ 7.143789] Bluetooth: HCI device and connection manager initialized [ 7.150295] Bluetooth: HCI socket layer initialized [ 7.155244] Bluetooth: L2CAP socket layer initialized [ 7.157344] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 7.160421] Bluetooth: SCO socket layer initialized [ 7.195166] usbcore: registered new interface driver btusb [ 7.216942] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [ 7.230824] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 7.236950] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ 7.251833] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 7.258411] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2 [ OK ] Found device /dev/mmcblk0p5.[ 7.267833] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 [ 7.298126] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 7.305118] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 7.313906] cfg80211: failed to load regulatory.db [ OK ] Found device /dev/mmcblk0p6. Starting File System Check on /dev/mmcblk0p6... Activating swap /dev/mmcblk0p5... [ 7.705159] RTL871X: module init start [ 7.709041] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40 [ 7.716090] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ 7.755876] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SS [ OK ] Activated swap /dev/mmcblk0p5. [ OK ] Started File System Check on /dev/mmcblk0p6. [ 7.897082] RTL871X: rtw_ndev_init(wlan0) [ 7.902406] RTL871X: rtw_ndev_init(wlan1) [ 7.907927] usbcore: registered new interface driver rtl8723bu [ 7.913786] RTL871X: module init ret=0 [ 7.998256] usbcore: registered new interface driver rtl8xxxu [ 8.124002] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Mounting /mnt/data... [ OK ] Reached target Swap. [ 8.758806] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /mnt/data. Starting Load/Save RF Kill Switch Status... Mounting /var/log... [ OK ] Mounted /var/log. [ OK ] Started Load/Save RF Kill Switch Status. Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems. [ OK ] Started ifup for wlan0. [ OK ] Started ifup for eth1. [ OK ] Started ifup for eth0. Starting prepare mounts and symlinks to config files... [ 9.179903] systemd-journald[123]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ 9.959279] RTL871X: RTW_ADAPTIVITY_EN_ [ 9.959306] AUTO, chplan:0x20, Regulation:3,3 [ 9.967629] RTL871X: RTW_ADAPTIVITY_MODE_ [ 9.967641] NORMAL [ OK ] Started prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Monitor directories with device templates for wb-mqtt-serial. [ OK ] Reached target Paths. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on KNX Daemon (socket). [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting Restore local date from Wiren Board GSM RTC... Starting System Logging Service... Starting Restore /etc/resolv.conf i…fore the ppp link was shut down... Starting Mosquitto MQTT v3.1/v3.1.1 Broker... Starting initialize filesystems at first boot... [ OK ] Started watch config files. Starting Initialize Wiren Board Device Tree overlays... [ OK ] Started Generates wb-mqtt-serial UI schema for wb-mqtt-confed. Starting Login Service... [ OK ] Started Cgroup management daemon. [ OK ] Started D-Bus System Message Bus. [ 12.647647] new mount options do not match the existing superblock, will be ignored Starting Bluetooth service... [ 12.728036] RTL871X: nolinked power save enter [ OK ] Started System Logging Service. [ OK ] Started Restore /etc/resolv.conf if…before the ppp link was shut down. [ OK ] Started Mosquitto MQTT v3.1/v3.1.1 Broker. [ 12.846979] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 12.852373] Bluetooth: BNEP filters: protocol multicast [ 12.857807] Bluetooth: BNEP socket layer initialized [ OK ] Started Bluetooth service. [ OK ] Started Login Service. Starting Hostname Service... [ OK ] Reached target Bluetooth. [ OK ] Started Wiren Board configuration editor backend. [ OK ] Started Wiren Board firmware update service. Starting Wiren Board MQTT to OPC UA gateway... [ 13.228811] EXT4-fs (mmcblk0p3): recovery complete [ 13.233762] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) Starting Wiren Board MQTT to Modbus TCP gateway... [ 13.287505] dwmac-sun8i 1c50000.ethernet eth1: PHY [stmmac-1:00] driver [ICPlus IP101A/G] (irq=POLL) [ 13.307676] dwmac-sun8i 1c50000.ethernet eth1: No Safety Features support found [ 13.315060] dwmac-sun8i 1c50000.ethernet eth1: No MAC Management Counters available [ 13.322977] dwmac-sun8i 1c50000.ethernet eth1: PTP not supported by HW [ 13.330803] dwmac-sun8i 1c50000.ethernet eth1: configuring for phy/mii link mode [ OK ] Started Hostname Service. [ OK ] Started Wiren Board MQTT to OPC UA gateway. [ OK ] Started Wiren Board MQTT to Modbus TCP gateway. [ 16.268044] random: crng init done [ 16.271477] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Started Restore local date from Wiren Board GSM RTC. [ OK ] Started initialize filesystems at first boot. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Avahi mDNS/DNS-SD Stack. [ 19.882715] 1c29000.serial: ttyS4 at MMIO 0x1c29000 (irq = 130, base_baud = 1500000) is a Allwinner sun4i [ OK ] Started Initialize Wiren Board Device Tree overlays. [ OK ] Started metrics sender.. Starting KNXD Configurator for Wiren Board... Starting Raise network interfaces... [ OK ] Started MQTT Rule engine for Wiren Board. [ OK ] Started one-click diagnostic data c…ard, generating archive with data. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. Starting Permit User Sessions... Starting KNX Daemon... [ OK ] Started MQTT Driver for serial devices. Starting OpenBSD Secure Shell server... [ OK ] Started Wiren Board journald to MQTT gateway. Starting MQTT Driver for GPIO-controlled switches... Starting dnsmasq - A lightweight DHCP and caching DNS server... Starting MQTT Driver for ADC... Starting A high performance web server and a reverse proxy server... [ OK ] Started Wiren Board database logger. [ OK ] Started KNX Daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started Wiren Board MQTT KNX bridge. [ OK ] Reached target Network is Online. Starting LSB: Brings up/down network automatically... Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Start NTP daemon... [ OK ] Started OpenBSD Secure Shell server. [ 22.733366] process '/sbin/netplugd' started with executable stack [ OK ] Started LSB: Start NTP daemon. Starting Compensation of systime in…evice-tree (with opposite sign)... [ OK ] Started Compensation of systime in … device-tree (with opposite sign). [ OK ] Stopped KNX Daemon. Starting KNX Daemon... [ 23.678547] RTL871X: RTW_ADAPTIVITY_EN_ [ 23.678581] AUTO, chplan:0x20, Regulation:3,3 [ 23.686971] RTL871X: RTW_ADAPTIVITY_MODE_ [ 23.686982] NORMAL [ 24.487160] RTL871X: nolinked power save leave [ OK ] Started KNX Daemon. [ OK ] Started KNXD Configurator for Wiren Board. [ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started MQTT Driver for ADC. [ 25.190602] RTL871X: assoc success [ 25.197928] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ OK ] Started LSB: Advanced IEEE 802.11 management daemon. [ OK ] Started A high performance web server and a reverse proxy server. Starting Initialize Wiren Board on successful boot... [ OK ] Started Initialize Wiren Board on successful boot. [ OK ] Started LSB: Brings up/down network automatically. Debian GNU/Linux 9 wirenboard-ADFA3S44 ttyS0 wirenboard-ADFA3S44 login: [ 34.405929] vcc-gmac-phy: disabling [ 34.409845] dc5ldo: disabling [ 34.419618] dldo4: disabling [ 34.423223] vdd-sd-power: disabling [ 34.426818] vcc-sd: disabling Debian GNU/Linux 9 wirenboard-ADFA3S44 ttyS0 wirenboard-ADFA3S44 login: root Password: _ _ _ __ _(_)_ __ ___ _ __ | |__ ___ __ _ _ __ __| | \ \ /\ / / | '__/ _ \ '_ \| '_ \ / _ \ / _` | '__/ _` | \ V V /| | | | __/ | | | |_) | (_) | (_| | | | (_| | \_/\_/ |_|_| \___|_| |_|_.__/ \___/ \__,_|_| \__,_| Welcome to Wiren Board 7.3.3 (s/n ADFA3S44), release wb-2207 (as stable) Linux wirenboard-ADFA3S44 5.10.35-wb120+wb101 #2 SMP Tue Nov 22 12:49:35 UTC 2022 armv7l GNU/Linux root@wirenboard-ADFA3S44:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 0bda:b720 Realtek Semiconductor Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@wirenboard-ADFA3S44:~# dmesg | grep sda root@wirenboard-ADFA3S44:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb120+wb101 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #2 SMP Tue Nov 22 12:49:35 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 7.3.3 (A40i) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x7ec00000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] Normal zone: 1728 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 19 pages/cpu s47884 r8192 d21748 u77824 [ 0.000000] pcpu-alloc: s47884 r8192 d21748 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1006628K/1048576K available (9216K kernel code, 1430K rwdata, 3068K rodata, 1024K init, 293K bss, 25564K reserved, 16384K cma-reserved, 245748K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 29913 entries in 59 pages [ 0.000000] ftrace: allocated 59 pages with 5 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x660/0x840 with crng_init=0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000011] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000034] Switching to timer-based delay loop, resolution 41ns [ 0.000506] Console: colour dummy device 80x30 [ 0.000596] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000638] pid_max: default: 32768 minimum: 301 [ 0.000919] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.000954] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002186] CPU: Testing write buffer coherency: ok [ 0.002625] /cpus/cpu@0 missing clock-frequency property [ 0.002676] /cpus/cpu@1 missing clock-frequency property [ 0.002722] /cpus/cpu@2 missing clock-frequency property [ 0.002770] /cpus/cpu@3 missing clock-frequency property [ 0.002788] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005432] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.005744] rcu: Hierarchical SRCU implementation. [ 0.006897] smp: Bringing up secondary CPUs ... [ 0.018112] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.029473] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.042010] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.042547] smp: Brought up 1 node, 4 CPUs [ 0.042634] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.042665] CPU: All CPU(s) started in HYP mode. [ 0.042694] CPU: Virtualization extensions available. [ 0.044207] devtmpfs: initialized [ 0.066635] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.067012] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.067053] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.068123] pinctrl core: initialized pinctrl subsystem [ 0.071404] NET: Registered protocol family 16 [ 0.075814] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.077742] thermal_sys: Registered thermal governor 'step_wise' [ 0.078306] No ATAGs? [ 0.078553] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.078571] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.161479] SCSI subsystem initialized [ 0.162685] usbcore: registered new interface driver usbfs [ 0.162846] usbcore: registered new interface driver hub [ 0.163005] usbcore: registered new device driver usb [ 0.163705] mc: Linux media interface: v0.10 [ 0.163797] videodev: Linux video capture interface: v2.00 [ 0.163900] pps_core: LinuxPPS API ver. 1 registered [ 0.163924] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.163989] PTP clock support registered [ 0.164462] Advanced Linux Sound Architecture Driver Initialized. [ 0.165777] clocksource: Switched to clocksource arch_sys_counter [ 1.354160] NET: Registered protocol family 2 [ 1.355219] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.355296] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.355412] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.355579] TCP: Hash tables configured (established 8192 bind 8192) [ 1.355834] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.355922] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.356265] NET: Registered protocol family 1 [ 1.358582] RPC: Registered named UNIX socket transport module. [ 1.358642] RPC: Registered udp transport module. [ 1.358677] RPC: Registered tcp transport module. [ 1.358709] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.361233] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 1.364119] Initialise system trusted keyrings [ 1.364649] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 1.378995] NFS: Registering the id_resolver key type [ 1.379074] Key type id_resolver registered [ 1.379310] Key type id_legacy registered [ 1.381021] Key type asymmetric registered [ 1.381061] Asymmetric key parser 'x509' registered [ 1.381343] bounce: pool size: 64 pages [ 1.381441] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.381471] io scheduler mq-deadline registered [ 1.381496] io scheduler kyber registered [ 1.383072] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.534454] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.558829] brd: module loaded [ 1.578244] loop: module loaded [ 1.587977] libphy: Fixed MDIO Bus: probed [ 1.590098] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 1.590937] libphy: sun4i_mii_bus: probed [ 1.594827] CAN device driver interface [ 1.597442] PPP generic driver version 2.4.2 [ 1.598477] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.598537] ehci-platform: EHCI generic platform driver [ 1.600611] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.600664] ohci-platform: OHCI generic platform driver [ 1.602061] usbcore: registered new interface driver usb-storage [ 1.602193] usbcore: registered new interface driver usbserial_generic [ 1.602239] usbserial: USB Serial support registered for generic [ 1.606506] sun6i-rtc 1c20400.rtc: registered as rtc1 [ 1.606537] sun6i-rtc 1c20400.rtc: RTC enabled [ 1.607034] i2c /dev entries driver [ 1.617986] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.623313] ledtrig-cpu: registered to indicate activity on CPUs [ 1.624063] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) from 24000000 (24 Mhz) [ 1.624435] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.625548] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.626519] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.626967] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.627256] sun8i-ce 1c15000.crypto: Register cbc(aes) [ 1.627603] sun8i-ce 1c15000.crypto: Register ecb(aes) [ 1.627897] sun8i-ce 1c15000.crypto: Register cbc(des3_ede) [ 1.628183] sun8i-ce 1c15000.crypto: Register ecb(des3_ede) [ 1.628471] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0 [ 1.631507] usbcore: registered new interface driver usbhid [ 1.631556] usbhid: USB HID core driver [ 1.635456] iio-rescale a1-volt: using raw+scale source channel [ 1.636758] iio-rescale a2-volt: using raw+scale source channel [ 1.637680] iio-rescale a3-volt: using raw+scale source channel [ 1.638326] iio-rescale vin-volt: using raw+scale source channel [ 1.644218] NET: Registered protocol family 10 [ 1.645590] Segment Routing with IPv6 [ 1.645694] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.646627] NET: Registered protocol family 17 [ 1.646660] can: controller area network core [ 1.647353] NET: Registered protocol family 29 [ 1.647422] can: raw protocol [ 1.647482] can: broadcast manager protocol [ 1.647561] can: netlink gateway - max_hops=1 [ 1.648221] Key type dns_resolver registered [ 1.648387] Registering SWP/SWPB emulation handler [ 1.648618] registered taskstats version 1 [ 1.648723] Loading compiled-in X.509 certificates [ 1.683195] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.690241] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 1.692567] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator [ 1.700380] printk: console [ttyS0] disabled [ 1.700559] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 52, base_baud = 1500000) is a Allwinner sun4i [ 2.658758] printk: console [ttyS0] enabled [ 2.665250] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PI regulator [ 2.672096] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 274 [ 2.678746] sun4i-pinctrl 1c20800.pinctrl: pin-274 (1c28800.serial) status -517 [ 2.686108] sun4i-pinctrl 1c20800.pinctrl: could not request pin 274 (PI18) from group PI18 on device 1c20800.pinctrl [ 2.696857] dw-apb-uart 1c28800.serial: Error applying setting, reverse things back [ 2.705366] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 2.714235] libphy: sun4i_mii_bus: probed [ 2.720021] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.726872] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 236 [ 2.733567] sun4i-pinctrl 1c20800.pinctrl: pin-236 (1c20800.pinctrl:236) status -517 [ 2.743809] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.750722] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 232 [ 2.757414] sun4i-pinctrl 1c20800.pinctrl: pin-232 (1c0b000.ethernet) status -517 [ 2.764910] sun4i-pinctrl 1c20800.pinctrl: could not request pin 232 (PH8) from group PH8 on device 1c20800.pinctrl [ 2.775445] sun4i-emac 1c0b000.ethernet: Error applying setting, reverse things back [ 2.785047] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 2.791872] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 2.798331] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -517 [ 2.805665] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 2.816121] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse things back [ 2.835871] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 2.850140] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0034/axp221-pek/input/input0 [ 2.873496] vcc-3v3: supplied by regulator-dummy [ 2.879345] vdd-cpu: supplied by regulator-dummy [ 2.885042] vdd-sys: supplied by regulator-dummy [ 2.890775] dcdc4: supplied by regulator-dummy [ 2.896287] vcc-dram: supplied by regulator-dummy [ 2.901218] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER [ 2.908426] vcc-gmac-phy: supplied by vcc-3v3 [ 2.915157] dc5ldo: supplied by vcc-dram [ 2.920550] tv: Bringing 700000uV into 3300000-3300000uV [ 2.927093] tv: supplied by regulator-dummy [ 2.932237] aldo2: Bringing 2500000uV into 3300000-3300000uV [ 2.938825] aldo2: supplied by regulator-dummy [ 2.944924] avcc-pll: supplied by regulator-dummy [ 2.950229] random: fast init done [ 2.954393] eldo1: supplied by regulator-dummy [ 2.960404] eldo2: supplied by regulator-dummy [ 2.965716] vcc-pe: Bringing 1200000uV into 1800000-1800000uV [ 2.972726] vcc-pe: supplied by regulator-dummy [ 2.977967] vcc-sd-alt: Bringing 700000uV into 1800000-1800000uV [ 2.986218] vcc-sd-alt: supplied by regulator-dummy [ 2.992851] dldo2: supplied by regulator-dummy [ 2.998777] dldo3: supplied by regulator-dummy [ 3.004513] dldo4: supplied by regulator-dummy [ 3.009893] rtc_ldo: supplied by regulator-dummy [ 3.015661] ldo_io0: supplied by regulator-dummy [ 3.021456] ldo_io1: supplied by regulator-dummy [ 3.027094] axp20x-adc axp22x-adc: DMA mask not set [ 3.034288] axp20x-battery-power-supply axp20x-battery-power-supply: DMA mask not set [ 3.044681] axp20x-i2c 0-0034: AXP20X driver loaded [ 3.078780] rtc-pcf85063 2-0051: registered as rtc0 [ 3.093192] rtc-pcf85063 2-0051: setting system clock to 2023-03-28T12:33:22 UTC (1680006802) [ 3.102606] lm75 2-0048: supply vs not found, using dummy regulator [ 3.113515] lm75 2-0048: hwmon1: sensor 'lm75b' [ 3.152400] sun4i-usb-phy 1c13400.phy: phy0 dr_mode=3 [ 3.161012] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 53, base_baud = 1500000) is a Allwinner sun4i [ 3.171449] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 3.179441] libphy: sun4i_mii_bus: probed [ 3.185832] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, uses new timings mode [ 3.318492] mmc0: new DDR MMC card at address 0001 [ 3.319279] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 65 MAC: 00:85:01:01:0b:5f [ 3.324162] mmcblk0: mmc0:0001 008GB0 7.28 GiB [ 3.332559] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 3.336470] mmcblk0boot0: mmc0:0001 008GB0 partition 1 8.00 MiB [ 3.342450] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 3.348788] mmcblk0boot1: mmc0:0001 008GB0 partition 2 8.00 MiB [ 3.354792] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 3.360556] mmcblk0rpmb: mmc0:0001 008GB0 partition 3 4.00 MiB, chardev (246:0) [ 3.366420] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supported [ 3.380608] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supported [ 3.387892] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 3.392859] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 3.399663] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 3.405321] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 3.411689] libphy: stmmac: probed [ 3.416831] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 3.678525] ehci-platform 1c14000.usb: EHCI Host Controller [ 3.684141] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 3.692318] ehci-platform 1c14000.usb: irq 37, io mem 0x01c14000 [ 3.725771] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 3.732899] hub 1-0:1.0: USB hub found [ 3.736767] hub 1-0:1.0: 1 port detected [ 3.741927] ehci-platform 1c19000.usb: EHCI Host Controller [ 3.747554] ehci-platform 1c19000.usb: new USB bus registered, assigned bus number 2 [ 3.755552] ehci-platform 1c19000.usb: irq 39, io mem 0x01c19000 [ 3.785769] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 3.792781] hub 2-0:1.0: USB hub found [ 3.796612] hub 2-0:1.0: 1 port detected [ 3.801697] ehci-platform 1c1c000.usb: EHCI Host Controller [ 3.807317] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 3 [ 3.815309] ehci-platform 1c1c000.usb: irq 41, io mem 0x01c1c000 [ 3.846399] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 3.853351] hub 3-0:1.0: USB hub found [ 3.857177] hub 3-0:1.0: 1 port detected [ 3.955861] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 3.962498] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 4 [ 3.970464] ohci-platform 1c14400.usb: irq 38, io mem 0x01c14400 [ 4.050638] hub 4-0:1.0: USB hub found [ 4.054454] hub 4-0:1.0: 1 port detected [ 4.059575] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 4.066255] ohci-platform 1c19400.usb: new USB bus registered, assigned bus number 5 [ 4.074272] ohci-platform 1c19400.usb: irq 40, io mem 0x01c19400 [ 4.150691] hub 5-0:1.0: USB hub found [ 4.154498] hub 5-0:1.0: 1 port detected [ 4.159620] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 4.166294] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 6 [ 4.174087] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 4.181364] ohci-platform 1c1c400.usb: irq 42, io mem 0x01c1c400 [ 4.260705] hub 6-0:1.0: USB hub found [ 4.264515] hub 6-0:1.0: 1 port detected [ 4.270607] of_cfs_init [ 4.271945] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 4.273181] of_cfs_init: OK [ 4.284947] ALSA device list: [ 4.287981] No soundcards found. [ 4.302979] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 4.319502] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 4.327731] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 4.338827] devtmpfs: mounted [ 4.346477] Freeing unused kernel memory: 1024K [ 4.376091] Run /sbin/init as init process [ 4.380191] with arguments: [ 4.380199] /sbin/init [ 4.380205] with environment: [ 4.380211] HOME=/ [ 4.380217] TERM=linux [ 4.544558] random: systemd: uninitialized urandom read (16 bytes read) [ 4.556840] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 4.577089] systemd[1]: Detected architecture arm. [ 4.617270] systemd[1]: Set hostname to . [ 4.644234] random: systemd: uninitialized urandom read (16 bytes read) [ 4.682136] random: systemd-cryptse: uninitialized urandom read (16 bytes read) [ 4.867800] systemd[1]: [/lib/systemd/system/wb-mqtt-w1.service:10] Unknown lvalue 'StartLimitIntervalSec' in section 'Service' [ 4.925991] systemd[1]: Listening on udev Kernel Socket. [ 4.966769] systemd[1]: Created slice User and Session Slice. [ 5.006311] systemd[1]: Listening on Journal Socket. [ 5.056128] systemd[1]: Listening on udev Control Socket. [ 5.096323] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 5.136040] systemd[1]: Reached target Remote File Systems. [ 6.069616] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ 6.893785] Driver for 1-wire Dallas network protocol. [ 7.053931] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator [ 7.135410] Bluetooth: Core ver 2.22 [ 7.139308] NET: Registered protocol family 31 [ 7.143789] Bluetooth: HCI device and connection manager initialized [ 7.150295] Bluetooth: HCI socket layer initialized [ 7.155244] Bluetooth: L2CAP socket layer initialized [ 7.157344] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 7.160421] Bluetooth: SCO socket layer initialized [ 7.195166] usbcore: registered new interface driver btusb [ 7.216942] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [ 7.230824] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 7.236950] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ 7.251833] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 7.258411] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2 [ 7.267833] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 [ 7.298126] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 7.305118] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 7.313906] cfg80211: failed to load regulatory.db [ 7.705159] RTL871X: module init start [ 7.709041] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40 [ 7.716090] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ 7.755876] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SS [ 7.897082] RTL871X: rtw_ndev_init(wlan0) [ 7.902406] RTL871X: rtw_ndev_init(wlan1) [ 7.907927] usbcore: registered new interface driver rtl8723bu [ 7.913786] RTL871X: module init ret=0 [ 7.998256] usbcore: registered new interface driver rtl8xxxu [ 8.124002] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 [ 8.758806] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [ 9.179903] systemd-journald[123]: Received request to flush runtime journal from PID 1 [ 9.959279] RTL871X: RTW_ADAPTIVITY_EN_ [ 9.959306] AUTO, chplan:0x20, Regulation:3,3 [ 9.967629] RTL871X: RTW_ADAPTIVITY_MODE_ [ 9.967641] NORMAL [ 12.647647] new mount options do not match the existing superblock, will be ignored [ 12.728036] RTL871X: nolinked power save enter [ 12.846979] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 12.852373] Bluetooth: BNEP filters: protocol multicast [ 12.857807] Bluetooth: BNEP socket layer initialized [ 13.228811] EXT4-fs (mmcblk0p3): recovery complete [ 13.233762] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 13.287505] dwmac-sun8i 1c50000.ethernet eth1: PHY [stmmac-1:00] driver [ICPlus IP101A/G] (irq=POLL) [ 13.307676] dwmac-sun8i 1c50000.ethernet eth1: No Safety Features support found [ 13.315060] dwmac-sun8i 1c50000.ethernet eth1: No MAC Management Counters available [ 13.322977] dwmac-sun8i 1c50000.ethernet eth1: PTP not supported by HW [ 13.330803] dwmac-sun8i 1c50000.ethernet eth1: configuring for phy/mii link mode [ 16.268044] random: crng init done [ 16.271477] random: 7 urandom warning(s) missed due to ratelimiting [ 19.882715] 1c29000.serial: ttyS4 at MMIO 0x1c29000 (irq = 130, base_baud = 1500000) is a Allwinner sun4i [ 22.733366] process '/sbin/netplugd' started with executable stack [ 23.678547] RTL871X: RTW_ADAPTIVITY_EN_ [ 23.678581] AUTO, chplan:0x20, Regulation:3,3 [ 23.686971] RTL871X: RTW_ADAPTIVITY_MODE_ [ 23.686982] NORMAL [ 24.487160] RTL871X: nolinked power save leave [ 25.190602] RTL871X: assoc success [ 25.197928] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 34.405929] vcc-gmac-phy: disabling [ 34.409845] dc5ldo: disabling [ 34.419618] dldo4: disabling [ 34.423223] vdd-sd-power: disabling [ 34.426818] vcc-sd: disabling root@wirenboard-ADFA3S44:~#