U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010f010f .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3e41 .p0_mpwrdlctl = 0x3f3f3835 .p0_mpwldectrl0 = 0x00000003 .p0_mpwldectrl1 = 0x000d000d Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 30C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Flash Rev: 6.90 Prod: USB Disk Type: Removable Hard Disk Capacity: 15000.0 MB = 14.6 GB (30720000 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) Skip 11333216 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8200125c) Skip 47891 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8200173c) Skip 34749 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82000f70) Skip 212224595 bytes of data reading wb6_update_FACTORYRESET.fit ** wb6_update_FACTORYRESET.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) reading wb6_update_FACTORYRESET.fit 11349856 bytes read in 6593 ms (1.6 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x82000300 Data Size: 11333216 Bytes = 10.8 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 855731103e35fa26fcdde99340a5980680759c13 ## Verifying ... sha1 U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010f010f .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3e41 .p0_mpwrdlctl = 0x3f3f3735 .p0_mpwldectrl0 = 0x00000003 .p0_mpwldectrl1 = 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 34C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Flash Rev: 6.90 Prod: USB Disk Type: Removable Hard Disk Capacity: 15000.0 MB = 14.6 GB (30720000 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) Skip 11333216 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8200125c) Skip 47891 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8200173c) Skip 34749 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82000f70) Skip 212224595 bytes of data reading wb6_update_FACTORYRESET.fit ** wb6_update_FACTORYRESET.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) reading wb6_update_FACTORYRESET.fit 11349856 bytes read in 6593 ms (1.6 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x82000300 Data Size: 11333216 Bytes = 10.8 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 855731103e35fa26fcdde99340a5980680759c13 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x83000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x83000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (830020c8) Skip 11333216 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8300125c) reading wb6_update_FACTORYRESET.fit 64975 bytes read in 496 ms (127 KiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x83000480 Data Size: 47891 Bytes = 46.8 KiB Architecture: ARM Hash algo: sha1 Hash value: 50379d0c7fb9a54564de1311fee0fb398cef285a ## Verifying ... sha1+ Loading part 0 ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef60000, end 9ef6eb12 ... OK Starting kernel ... U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010f010f .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3d41 .p0_mpwrdlctl = 0x3f3f3734 .p0_mpwldectrl0 = 0x00000003 .p0_mpwldectrl1 = 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 35C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Flash Rev: 6.90 Prod: USB Disk Type: Removable Hard Disk Capacity: 15000.0 MB = 14.6 GB (30720000 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010f010f .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3e42 .p0_mpwrdlctl = 0x3f3f3735 .p0_mpwldectrl0 = 0x00000003 .p0_mpwldectrl1 = 0x00070007 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 36C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Flash Rev: 6.90 Prod: USB Disk Type: Removable Hard Disk Capacity: 15000.0 MB = 14.6 GB (30720000 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 20 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010f010f .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3e41 .p0_mpwrdlctl = 0x3f3f3835 .p0_mpwldectrl0 = 0x00000003 .p0_mpwldectrl1 = 0x00090009 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 37C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Flash Rev: 6.90 Prod: USB Disk Type: Removable Hard Disk Capacity: 15000.0 MB = 14.6 GB (30720000 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 20 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0 = 0x010f010f .p0_mpdgctrl1 = 0x0e3f0e3f .p0_mprddlctl = 0x3f3f3d42 .p0_mpwrdlctl = 0x3f3f3835 .p0_mpwldectrl0 = 0x00000003 .p0_mpwldectrl1 = 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 38C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 1