=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.09.07 11:26:12 =~=~=~=~=~=~=~=~=~=~=~= [68871.432872] usb 1-1: new high-speed USB device number 2 using ci_hdrc [68871.715176] usb 1-1: New USB device found, idVendor U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01120110 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f3d40 .p0_mpwrdlctl= 0x3f3f3938 .p0_mpwldectrl0= 0x00070005 .p0_mpwldectrl1= 0x00080008 Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 49C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3 2 1 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra USB 3.0 Type: Removable Hard Disk Capacity: 14664.0 MB = 14.3 GB (30031872 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit ** Unable to read file wb6_update_FACTORYRESET.fit ** No USB update detected, continuing boot switch to partitions #0, OK mmc0(part 0) is current device SD/MMC found on device 0 324 bytes read in 68 ms (3.9 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 5899176 bytes read in 395 ms (14.2 MiB/s) MMC read: dev # 0, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard690 47008 bytes read in 118 ms (388.7 KiB/s) 485 bytes read in 151 ms (2.9 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 145 ms (3.9 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 173 ms (2 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 112 ms (2 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 125 ms (2 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef4c000, end 9ef6efff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb111 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 6.3.0-18) 6.3.0 20170516, GNU ld (GNU Binutils for Debian) 2.28) #1 Wed Apr 20 13:39:52 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.9.0 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9f000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait ro [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 489384K/524288K available (8192K kernel code, 714K rwdata, 2680K rodata, 1024K init, 272K bss, 18520K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x238/0x3d4 with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000062] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002845] Console: colour dummy device 80x30 [ 0.002912] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002952] pid_max: default: 32768 minimum: 301 [ 0.003382] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003417] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.005005] CPU: Testing write buffer coherency: ok [ 0.006106] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.006993] devtmpfs: initialized [ 0.025183] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.025717] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025766] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.027134] pinctrl core: initialized pinctrl subsystem [ 0.029168] NET: Registered protocol family 16 [ 0.031485] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033549] thermal_sys: Registered thermal governor 'step_wise' [ 0.033841] cpuidle: using governor menu [ 0.233784] vdd1p1: supplied by regulator-dummy [ 0.246653] vdd3p0: supplied by regulator-dummy [ 0.259542] cpu: supplied by regulator-dummy [ 0.272502] vddsoc: supplied by regulator-dummy [ 0.636067] No ATAGs? [ 0.636131] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.636156] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.636771] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.637428] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.638863] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.638902] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.679879] mxs-dma 1804000.dma-apbh: initialized [ 0.685285] SCSI subsystem initialized [ 0.685799] usbcore: registered new interface driver usbfs [ 0.685929] usbcore: registered new interface driver hub [ 0.686040] usbcore: registered new device driver usb [ 0.686876] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.687026] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.688348] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.689268] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.689408] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.690016] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.690718] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.690853] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.691462] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.693019] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.693456] i2c i2c-1: IMX I2C adapter registered [ 0.694207] mc: Linux media interface: v0.10 [ 0.694327] videodev: Linux video capture interface: v2.00 [ 0.694510] pps_core: LinuxPPS API ver. 1 registered [ 0.694534] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.694594] PTP clock support registered [ 0.695245] Advanced Linux Sound Architecture Driver Initialized. [ 0.697362] clocksource: Switched to clocksource mxc_timer1 [ 0.715433] NET: Registered protocol family 2 [ 0.716641] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.716754] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.716873] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.716981] TCP: Hash tables configured (established 4096 bind 4096) [ 0.717179] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.717232] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.717741] NET: Registered protocol family 1 [ 0.718686] RPC: Registered named UNIX socket transport module. [ 0.718722] RPC: Registered udp transport module. [ 0.718740] RPC: Registered tcp transport module. [ 0.718757] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.719946] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.722821] Initialise system trusted keyrings [ 0.723270] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.735074] NFS: Registering the id_resolver key type [ 0.735153] Key type id_resolver registered [ 0.735172] Key type id_legacy registered [ 0.736069] Key type asymmetric registered [ 0.736107] Asymmetric key parser 'x509' registered [ 0.736210] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.736236] io scheduler mq-deadline registered [ 0.736255] io scheduler kyber registered [ 0.748536] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.748586] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.752565] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX [ 1.415493] printk: console [ttymxc0] enabled [ 1.422001] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX [ 1.465865] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.473301] random: fast init done [ 1.477250] random: crng init done [ 1.516837] brd: module loaded [ 1.534727] loop: module loaded [ 1.538347] at24 5-0050: supply vcc not found, using dummy regulator [ 1.549819] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.556794] at24 6-0050: supply vcc not found, using dummy regulator [ 1.568262] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.580755] libphy: Fixed MDIO Bus: probed [ 1.708045] pps pps0: new PPS source ptp0 [ 1.714477] libphy: fec_enet_mii_bus: probed [ 1.723310] fec 20b4000.ethernet eth0: registered PHC device 0 [ 1.848076] pps pps1: new PPS source ptp1 [ 1.888665] libphy: fec_enet_mii_bus: probed [ 1.893973] fec 2188000.ethernet eth1: registered PHC device 1 [ 1.900834] PPP generic driver version 2.4.2 [ 1.905554] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.912207] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.917967] usbcore: registered new interface driver usb-storage [ 1.924233] usbcore: registered new interface driver usbserial_generic [ 1.930919] usbserial: USB Serial support registered for generic [ 1.980321] rtc rtc0: invalid alarm value: 2022-09-07T38:25:00 [ 1.986617] rtc-pcf8563 4-0051: registered as rtc0 [ 2.003457] rtc-pcf8563 4-0051: setting system clock to 2022-09-07T08:26:25 UTC (1662539185) [ 2.022235] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1 [ 2.028776] i2c /dev entries driver [ 2.035599] lm75 4-0048: supply vs not found, using dummy regulator [ 2.047263] lm75 4-0048: hwmon0: sensor 'lm75b' [ 2.167794] sdhci: Secure Digital Host Controller Interface driver [ 2.174006] sdhci: Copyright(c) Pierre Ossman [ 2.178427] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.192332] ledtrig-cpu: registered to indicate activity on CPUs [ 2.200177] usbcore: registered new interface driver usbhid [ 2.205777] usbhid: USB HID core driver [ 2.222362] NET: Registered protocol family 10 [ 2.226950] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA [ 2.236890] Segment Routing with IPv6 [ 2.241417] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.249434] NET: Registered protocol family 17 [ 2.254198] Key type dns_resolver registered [ 2.263008] registered taskstats version 1 [ 2.267193] Loading compiled-in X.509 certificates [ 2.289516] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.301414] of_cfs_init [ 2.304172] of_cfs_init: OK [ 2.312030] ALSA device list: [ 2.315034] No soundcards found. [ 2.318827] Waiting for root device /dev/mmcblk0p3... [ 2.328509] mmc0: new DDR MMC card at address 0001 [ 2.334201] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.339248] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 2.345539] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 2.351907] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (245:0) [ 2.362358] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 2.384317] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem [ 2.391729] EXT4-fs (mmcblk0p3): write access will be enabled during recovery [ 2.764018] EXT4-fs (mmcblk0p3): recovery complete [ 2.771449] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 2.780009] VFS: Mounted root (ext4 filesystem) readonly on device 179:3. [ 2.787514] devtmpfs: mounted [ 2.791826] Freeing unused kernel memory: 1024K [ 2.796630] Run /sbin/init as init process [ 3.125705] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 3.144756] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 3.188385] systemd[1]: Set hostname to . [ 3.717090] systemd[1]: [/lib/systemd/system/wb-mqtt-w1.service:10] Unknown lvalue 'StartLimitIntervalSec' in section 'Service' [ 3.800405] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 3.838032] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 3.868249] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 3.911037] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 3.952854] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. [ 3.992216] systemd[1]: Mounting /sys/kernel/config... Mounting /sys/kernel/config... Mounting Debug File System... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on Journal Socket. Starting Load Kernel Modules... Starting File System Check on Root Device... [ OK ] Reached target Remote File Systems. Starting Create list of required stce nodes for the current kernel... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on udev Kernel Socket. Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Syslog Socket. [ OK ] Created slice system-getty.slice. Starting Journal Service... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted /sys/kernel/config. [ OK ] Started Journal Service. [ OK ] Started Load Kernel Modules. [ OK ] Started File System Check on Root Device. [ OK ] Started Create list of required stavice nodes for the current kernel. [ OK ] Started File System Check Daemon to report status. Starting Create Static Device Nodes in /dev... Starting Remount Root and Kernel File Systems... Starting Apply Kernel Variables... [ OK ] Started Create Static Device Nodes in /dev. [ 5.063639] EXT4-fs (mmcblk0p3): re-mounted. Opts: errors=remount-ro [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Apply Kernel Variables. Starting prepare partitions at first boot... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting udev Kernel Device Manager... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started prepare partitions at first boot. [ OK ] Reached target Local File Systems (Pre). [ 7.116550] Driver for 1-wire Dallas network protocol. [ OK ] Started udev Coldplug all Devices. [ 7.179157] gpio-68 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 7.276132] gpio-11 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ OK ] Found device /dev/ttymxc0. [ 7.533677] fec 20b4000.ethernet rename2: renamed from eth0 [ 7.959163] imx_usb 2184000.usb: No over current polarity defined [ 8.033002] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 8.067503] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 8.106744] fec 2188000.ethernet eth0: renamed from eth1 [ 8.137493] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 8.157987] fec 20b4000.ethernet eth1: renamed from rename2 [ 8.170508] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 8.178897] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.186130] usb usb1: Product: EHCI Host Controller [ 8.191048] usb usb1: Manufacturer: Linux 5.10.35-wb111 ehci_hcd [ 8.197062] usb usb1: SerialNumber: ci_hdrc.0 [ 8.512460] hub 1-0:1.0: USB hub found [ 8.589176] hub 1-0:1.0: 1 port detected [ 8.674899] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 8.716574] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 8.827506] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 8.854614] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 8.863003] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.870272] usb usb2: Product: EHCI Host Controller [ 8.875159] usb usb2: Manufacturer: Linux 5.10.35-wb111 ehci_hcd [ 8.881201] usb usb2: SerialNumber: ci_hdrc.1 [ 9.084482] hub 2-0:1.0: USB hub found [ 9.127570] usb usb1-port1: over-current condition [ 9.138216] hub 2-0:1.0: 1 port detected [ 9.297509] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ OK ] Found device /dev/mmcblk0p5. [ 9.517464] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 9.538893] usb 1-1: New USB device found, idVendor=0781, idProduct=5591, bcdDevice= 1.00 [ 9.547141] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.554359] usb 1-1: Product: Ultra USB 3.0 [ 9.558568] usb 1-1: Manufacturer: SanDisk [ 9.562671] usb 1-1: SerialNumber: 4C530000090318211233 [ OK ] Found device /dev/mmcblk0p6. [ 9.763720] usb-storage 1-1:1.0: USB Mass Storage device detected [ 9.788099] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 9.796326] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 9.927916] hub 2-1:1.0: USB hub found [ 9.937173] scsi host0: usb-storage 1-1:1.0 [ 9.974347] hub 2-1:1.0: 4 ports detected Starting File System Check on /dev/mmcblk0p6... Activating swap /dev/mmcblk0p5... [ 10.328335] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ 10.357209] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SS [ OK ] Activated swap /dev/mmcblk0p5. [ OK ] Reached target Swap. [ 10.489727] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00 [ 10.498182] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.505545] usb 2-1.1: Product: 802.11n WLAN Adapter [ 10.510561] usb 2-1.1: Manufacturer: Realtek [ 10.514845] usb 2-1.1: SerialNumber: 00e04c000001 [ 10.772683] Bluetooth: Core ver 2.22 [ 10.785594] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ 10.809502] NET: Registered protocol family 31 [ 10.814001] Bluetooth: HCI device and connection manager initialized [ 10.842673] Bluetooth: HCI socket layer initialized [ 10.848108] Bluetooth: L2CAP socket layer initialized [ 10.854599] Bluetooth: SCO socket layer initialized [ 10.947961] usbcore: registered new interface driver btusb [ 10.968711] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [ 10.978770] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 10.984844] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ 10.994845] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 11.001441] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2 [ 11.010864] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 Starting Load/Save RF Kill Switch Status... [ 11.040195] scsi 0:0:0:0: Direct-Access SanDisk Ultra USB 3.0 1.00 PQ: 0 ANSI: 6 [ 11.126199] sd 0:0:0:0: [sda] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB) [ 11.171484] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 11.188582] sd 0:0:0:0: [sda] Write Protect is off [ 11.204463] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 11.243469] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 11.264024] cfg80211: failed to load regulatory.db [ OK ] Started Load/Save RF Kill Switch Status. [ 11.298732] sda: sda1 [ 11.319445] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 11.846924] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 [ 11.984795] RTL871X: module init start [ 11.988692] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40 [ 11.995705] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ 12.189745] RTL871X: rtw_ndev_init(wlan0) [ 12.205304] RTL871X: rtw_ndev_init(wlan1) [ 12.225540] usbcore: registered new interface driver rtl8723bu [ 12.231469] RTL871X: module init ret=0 [ 12.340653] usbcore: registered new interface driver rtl8xxxu [ OK ] Found device 802.11n_WLAN_Adapter. [ OK ] Started File System Check on /dev/mmcblk0p6. Mounting /mnt/data... [ 13.056316] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /mnt/data. Mounting /var/log... [ OK ] Mounted /var/log. Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems. [ OK ] Started ifup for wlan0. [ OK ] Started ifup for eth1. Starting Raise network interfaces... [ OK ] Started ifup for eth0. Starting prepare mounts and symlinks to config files... [ OK ] Started Raise network interfaces. [ 13.740618] systemd-journald[110]: Received request to flush runtime journal from PID 1 [ 13.821984] systemd-journald[110]: File /var/log/journal/8caf4ac374ea3d589188523063088b32/system.journal corrupted or uncleanly shut down, renaming and replacing. [ OK ] Started Flush Journal to Persistent Storage. [ 15.213465] RTL871X: RTW_ADAPTIVITY_EN_ [ 15.213491] AUTO, chplan:0x20, Regulation:3,3 [ 15.221796] RTL871X: RTW_ADAPTIVITY_MODE_ [ 15.221801] NORMAL [ OK ] Started prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on KNX Daemon (socket). [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily apt download activities. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started Monitor directories with device templates for wb-mqtt-serial. [ OK ] Reached target Paths. [ OK ] Reached target Basic System. Starting Restore /etc/resolv.conf ifore the ppp link was shut down... [ OK ] Started Cgroup management daemon. [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. [ 17.255548] new mount options do not match the existing superblock, will be ignored Starting Bluetooth service... Starting Login Service... [ OK ] Started Generates wb-mqtt-serial UI schema for wb-mqtt-confed. Starting initialize filesystems at first boot... Starting System Logging Service... Starting Restore local date from Wiren Board GSM RTC... Starting Mosquitto MQTT v3.1/v3.1.1 Broker... [ OK ] Started watch config files. Starting Initialize Wiren Board Device Tree overlays... [ OK ] Started System Logging Service. [ 18.568809] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 18.574149] Bluetooth: BNEP filters: protocol multicast [ OK ] Started Restore /etc/resolv.conf ifbefore the ppp link was shut down. [ 18.722241] Bluetooth: BNEP socket layer initialized [ 18.729802] RTL871X: nolinked power save enter [ OK ] Started Mosquitto MQTT v3.1/v3.1.1 Broker. [ OK ] Started initialize filesystems at first boot. [ OK ] Started Bluetooth service. [ OK ] Started Login Service. Starting Hostname Service... [ OK ] Reached target Bluetooth. [ OK ] Reached target Network. Starting A high performance web server and a reverse proxy server... Starting dnsmasq - A lightweight DHCP and caching DNS server... Starting KNX Daemon... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Wiren Board configuration editor backend. Starting Wiren Board MQTT to Modbus TCP gateway... [ OK ] Started Wiren Board journald to MQTT gateway. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Started Wiren Board firmware update service. [ OK ] Started KNX Daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Hostname Service. [ OK ] Started Wiren Board MQTT to OPC UA gateway. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Network is Online. Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Start NTP daemon... Starting LSB: Brings up/down network automatically... [ OK ] Started OpenBSD Secure Shell server. [ 25.604260] process '/sbin/netplugd' started with executable stack [ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server. [ 25.927623] SMSC LAN8710/LAN8720 20b4000.ethernet-1:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:00, irq=POLL) [ OK ] Started LSB: Start NTP daemon. Starting Compensation of systime inevice-tree (with opposite sign)... [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started Compensation of systime in device-tree (with opposite sign). [ 28.167878] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 28.399435] RTL871X: RTW_ADAPTIVITY_EN_ [ 28.399459] AUTO, chplan:0x20, Regulation:3,3 [ 28.407760] RTL871X: RTW_ADAPTIVITY_MODE_ [ 28.407764] NORMAL [ 29.114715] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 224, base_baud = 5000000) is a IMX Debian GNU/Linux 9 wirenboard-AU34OFFG ttymxc0 wirenboard-AU34OFFG login: [ 30.936115] RTL871X: nolinked power save leave [ 31.287670] SMSC LAN8710/LAN8720 20b4000.ethernet-1:01: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) [ 31.364341] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.893689] RTL871X: assoc success [ 31.899104] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready