U-Boot SPL 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31) DRAM init ok, rows:15, ncs:1, size: 512MB Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 32C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 3  2  1  0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra USB 3.0 Type: Removable Hard Disk Capacity: 14664.0 MB = 14.3 GB (30031872 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) Skip 7965336 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82001624) Skip 46152 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820021d0) Skip 4085 bytes of data Skip 172856443 bytes of data reading wb6_update_FACTORYRESET.fit ** wb6_update_FACTORYRESET.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) reading wb6_update_FACTORYRESET.fit 7981976 bytes read in 4714 ms (1.6 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x82000300 Data Size: 7965336 Bytes = 7.6 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 324dcf61e352042acd1c3bdca4eceeff6f36cec3 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x83000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x83000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (830020c8) Skip 7965336 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (83001624) reading wb6_update_FACTORYRESET.fit 63236 bytes read in 454 ms (135.7 KiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x83000440 Data Size: 46152 Bytes = 45.1 KiB Architecture: ARM Hash algo: sha1 Hash value: c10a916cd509d98160cc0e99f9fe514dbe7c0c43 ## Verifying ... sha1+ Loading part 0 ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef60000, end 9ef6e447 ... OK Starting kernel ... U-Boot SPL 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31) DRAM init ok, rows:15, ncs:1, size: 512MB Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 38C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 3  2  1  0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra USB 3.0 Type: Removable Hard Disk Capacity: 14664.0 MB = 14.3 GB (30031872 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) Skip 7965336 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82001624) Skip 46152 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820021d0) Skip 4085 bytes of data Skip 172856443 bytes of data reading wb6_update_FACTORYRESET.fit ** wb6_update_FACTORYRESET.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (820020c8) reading wb6_update_FACTORYRESET.fit 7981976 bytes read in 4715 ms (1.6 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x82000300 Data Size: 7965336 Bytes = 7.6 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 324dcf61e352042acd1c3bdca4eceeff6f36cec3 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x83000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x83000100 ... reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (830020c8) Skip 7965336 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (83001624) reading wb6_update_FACTORYRESET.fit 63236 bytes read in 453 ms (135.7 KiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x83000440 Data Size: 46152 Bytes = 45.1 KiB Architecture: ARM Hash algo: sha1 Hash value: c10a916cd509d98160cc0e99f9fe514dbe7c0c43 ## Verifying ... sha1+ Loading part 0 ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef60000, end 9ef6e447 ... OK Starting kernel ... U-Boot SPL 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31) DRAM init ok, rows:15, ncs:1, size: 512MB Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 39C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@02188000 Hit any key to stop autoboot: 3  2  1  0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra USB 3.0 Type: Removable Hard Disk Capacity: 14664.0 MB = 14.3 GB (30031872 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 19 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ##############################