U-Boot 2017.03-1.0.2-g6ee0824fba (May 27 2019 - 16:14:52 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 41C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 0 Using default environment In: serial Out: serial Err: serial EEPROM #0 MAC: 04:91:62:c1:f0:ea EEPROM #1 MAC: 04:91:62:c2:1a:3b Net: No ethernet found. Hit any key to stop autoboot: 0 Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Kingston Rev: Prod: DataTraveler 3.0 Type: Removable Hard Disk Capacity: 29510.4 MB = 28.8 GB (60437492 x 512) reading wb6_update.fit ** Unable to read file wb6_update.fit ** reading wb6_update_FACTORYRESET.fit 1 bytes read in 25 ms (0 Bytes/s) ############################## # Detected USB flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit Skip 7928976 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8200042c) Skip 46505 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (82000e74) Skip 7066 bytes of data Skip 204335008 bytes of data reading wb6_update_FACTORYRESET.fit ** wb6_update_FACTORYRESET.fit shorter than offset + len ** Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x82000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x82000100 ... reading wb6_update_FACTORYRESET.fit reading wb6_update_FACTORYRESET.fit 7945616 bytes read in 4641 ms (1.6 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x82000300 Data Size: 7928976 Bytes = 7.6 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 47f6419e0d5d8326c41b16761827dc3d746fec78 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT strings to 0x83000028 ... reading wb6_update_FACTORYRESET.fit ## Loading FIT struct to 0x83000100 ... reading wb6_update_FACTORYRESET.fit Skip 7928976 bytes of data reading wb6_update_FACTORYRESET.fit FAT: Misaligned buffer address (8300042c) reading wb6_update_FACTORYRESET.fit 63589 bytes read in 450 ms (137.7 KiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x83000440 Data Size: 46505 Bytes = 45.4 KiB Architecture: ARM Hash algo: sha1 Hash value: ef9dd3fe2b348fb8eb9f150b9dc2e27d6899e823 ## Verifying ... sha1+ Loading part 0 ... OK Kernel image @ 0x82000000 [ 0x000000 - 0x78fc90 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef48000, end 9ef565a8 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.22-wb6_initramfs (root@WB-buildserver) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #2 SMP Tue Feb 1 16:52:01 2 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Wiren Board init (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 14 pages/cpu @cfbd0000 s25932 r8192 d23220 u57344 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=usbupdate,wb6_update_FACTORYRESET.fit [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506760K/524288K available (5120K kernel code, 202K rwdata, 1576K rodata, 5120K init, 295K bss, 17528K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xb0000000 - 0xd0000000 ( 512 MB) [ 0.000000] modules : 0xaf000000 - 0xb0000000 ( 16 MB) [ 0.000000] .text : 0xb0008000 - 0xb0600000 (6112 kB) [ 0.000000] .init : 0xb0800000 - 0xb0d00000 (5120 kB) [ 0.000000] .data : 0xb0d00000 - 0xb0d32880 ( 203 kB) [ 0.000000] .bss : 0xb0d34000 - 0xb0d7ddb0 ( 296 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000052] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002599] Console: colour dummy device 80x30 [ 0.002641] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002675] pid_max: default: 32768 minimum: 301 [ 0.002864] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002890] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.004098] CPU: Testing write buffer coherency: ok [ 0.004594] /cpus/cpu@0 missing clock-frequency property [ 0.004637] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004693] Setting up static identity map for 0x80100000 - 0x80100070 [ 0.007089] Brought up 1 CPUs [ 0.007124] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.007139] CPU: All CPU(s) started in SVC mode. [ 0.008349] devtmpfs: initialized [ 0.034424] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.035109] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.035160] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.035337] pinctrl core: initialized pinctrl subsystem [ 0.037407] NET: Registered protocol family 16 [ 0.037925] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.040365] cpuidle: using governor menu [ 0.075975] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.076008] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.078228] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.118472] mxs-dma 1804000.dma-apbh: initialized [ 0.122975] SCSI subsystem initialized [ 0.123579] usbcore: registered new interface driver usbfs [ 0.123747] usbcore: registered new interface driver hub [ 0.123994] usbcore: registered new device driver usb [ 0.125589] i2c-gpio i2c_rtc: using pins 48 (SDA) and 49 (SCL) [ 0.126461] i2c-gpio i2c_eeprom1: using pins 76 (SDA) and 67 (SCL) [ 0.127293] i2c-gpio i2c_eeprom2: using pins 70 (SDA) and 71 (SCL) [ 0.128784] i2c i2c-1: IMX I2C adapter registered [ 0.128828] i2c i2c-1: can't use DMA, using PIO instead. [ 0.129241] pps_core: LinuxPPS API ver. 1 registered [ 0.129265] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.129323] PTP clock support registered [ 0.131714] clocksource: Switched to clocksource mxc_timer1 [ 0.155472] NET: Registered protocol family 2 [ 0.156712] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.156834] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.156991] TCP: Hash tables configured (established 4096 bind 4096) [ 0.157108] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.157164] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.157466] NET: Registered protocol family 1 [ 0.158294] RPC: Registered named UNIX socket transport module. [ 0.158323] RPC: Registered udp transport module. [ 0.158339] RPC: Registered tcp transport module. [ 0.158353] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.727029] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.742325] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.744309] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.754745] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.754781] io scheduler noop registered (default) [ 0.759952] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.759994] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.769103] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX [ 1.323264] console [ttymxc0] enabled [ 1.328767] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 55, base_baud = 5000000) is a IMX [ 1.339050] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 56, base_baud = 5000000) is a IMX [ 1.381872] imx_rngc 2284000.rngb: Freescale RNGC registered. [ 1.416799] brd: module loaded [ 1.435858] loop: module loaded [ 1.444148] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.455590] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.463130] libphy: Fixed MDIO Bus: probed [ 1.469610] 20b4000.ethernet supply phy not found, using dummy regulator [ 1.477637] pps pps0: new PPS source ptp0 [ 1.510621] libphy: fec_enet_mii_bus: probed [ 1.516881] fec 20b4000.ethernet eth0: registered PHC device 0 [ 1.641799] 2188000.ethernet supply phy not found, using dummy regulator [ 1.762734] pps pps1: new PPS source ptp1 [ 1.767832] libphy: fec_enet_mii_bus: probed [ 1.775762] fec 2188000.ethernet eth1: registered PHC device 1 [ 1.782339] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.788910] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.794767] usbcore: registered new interface driver cdc_acm [ 1.800464] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.808952] usbcore: registered new interface driver usb-storage [ 1.859595] rtc rtc0: invalid alarm value: 2023-4-23 45:7:0 [ 1.865825] rtc-pcf8563 4-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 1.882058] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1 [ 1.891078] i2c /dev entries driver [ 1.899284] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 1.906780] imx6ul-pinctrl 20e0000.iomuxc: pin MX6UL_PAD_SD1_DATA1 already requested by watchdog; cannot claim for watchdog_6x [ 1.918331] imx6ul-pinctrl 20e0000.iomuxc: pin-114 (watchdog_6x) status -22 [ 1.925381] imx6ul-pinctrl 20e0000.iomuxc: could not request pin 114 (MX6UL_PAD_SD1_DATA1) from group wdggrp_6x on device 20e0000.iomuxc [ 1.937801] gpio-wdt watchdog_6x: Error applying setting, reverse things back [ 1.945030] gpio-wdt: probe of watchdog_6x failed with error -22 [ 1.952872] sdhci: Secure Digital Host Controller Interface driver [ 1.959100] sdhci: Copyright(c) Pierre Ossman [ 1.963579] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.031769] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 2.051346] ledtrig-cpu: registered to indicate activity on CPUs [ 2.058908] random: fast init done [ 2.079270] usbcore: registered new interface driver usbhid [ 2.087038] usbhid: USB HID core driver [ 2.101388] NET: Registered protocol family 17 [ 2.112370] Registering SWP/SWPB emulation handler [ 2.119418] registered taskstats version 1 [ 2.136420] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.159651] rtc-pcf8563 4-0051: setting system clock to 2023-04-12 09:11:44 UTC (1681290704) [ 2.168145] of_cfs_init [ 2.170799] of_cfs_init: OK [ 2.179694] vdd3p0: disabling [ 2.184866] vref-3v3: disabling [ 2.190111] usb1_vbus: disabling [ 2.202087] Freeing unused kernel memory: 5120K (b0800000 - b0d00000) [ 2.217808] mmc0: new DDR MMC card at address 0001 [ 2.237815] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB [ 2.252095] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB mount: mounting none on /dev/pts [ 2.262052] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB failed: No such file or directory [ 2.282331] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB [ 2.293103] mmcblk0: p1 p2 p3 p4 < p5 p6 > Boot mode: usbupdate,wb6_update_FACTORYRESET.fit Board is WB6, loading ci_hdrc_imx module [ 2.531942] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 2.536886] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 2.571772] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 2.577443] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.584302] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.591533] usb usb1: Product: EHCI Host Controller [ 2.596465] usb usb1: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd [ 2.603115] usb usb1: SerialNumber: ci_hdrc.0 [ 2.608956] hub 1-0:1.0: USB hub found [ 2.612963] hub 1-0:1.0: 1 port detected [ 2.618437] 2184200.usb supply vbus not found, using dummy regulator [ 2.629115] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.634209] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 2.661793] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.667570] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.674456] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.681738] usb usb2: Product: EHCI Host Controller [ 2.686632] usb usb2: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd [ 2.693322] usb usb2: SerialNumber: ci_hdrc.1 [ 2.699086] hub 2-0:1.0: USB hub found [ 2.703084] hub 2-0:1.0: 1 port detected [ 3.061874] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 3.252731] usb 2-1: New USB device found, idVendor=0424, idProduct=2514 [ 3.259554] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.269852] hub 2-1:1.0: USB hub found [ 3.274063] hub 2-1:1.0: 4 ports detected [ 3.381805] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.581660] usb 1-1: New USB device found, idVendor=0951, idProduct=1666 [ 3.588586] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.595960] usb 1-1: Product: DataTraveler 3.0 [ 3.600454] usb 1-1: Manufacturer: Kingston [ 3.604805] usb 1-1: SerialNumber: E0D55E6C389BF491790A4269 [ 3.610531] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ 3.622218] usb-storage 1-1:1.0: USB Mass Storage device detected [ 3.630048] scsi host0: usb-storage 1-1:1.0 [ 3.773492] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720 [ 3.780440] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.787872] usb 2-1.1: Product: 802.11n WLAN Adapter [ 3.792907] usb 2-1.1: Manufacturer: Realtek [ 3.797198] usb 2-1.1: SerialNumber: 00e04c000001 Load modules for USB to work Starting USB update Waiting for USB to settle (0/10) [ 4.644376] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6 [ 4.656969] sd 0:0:0:0: [sda] 60437492 512-byte logical blocks: (30.9 GB/28.8 GiB) [ 4.668191] sd 0:0:0:0: [sda] Write Protect is off [ 4.674432] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 4.693865] sda: sda1 sda4 [ 4.704414] sd 0:0:0:0: [sda] Attached SCSI removable disk umount: can't umount /usb: Invalid argument Looking for wb6_update_FACTORYRESET.fit on /dev/sda umount: can't umount /usb: Invalid argument mount: mounting /dev/sda on /usb failed: Invalid argument Looking for wb6_update_FACTORYRESET.fit on /dev/sda1 umount: ca