root@wirenboard-A2TEGFMO:~# dmesg -w [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb159+wb1 (root@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Mar 22 15:10:33 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 7.4.2 (A40i) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x7ec00000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] Normal zone: 1728 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 20 pages/cpu s50444 r8192 d23284 u81920 [ 0.000000] pcpu-alloc: s50444 r8192 d23284 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1004488K/1048576K available (10240K kernel code, 1478K rwdata, 3228K rodata, 1024K init, 306K bss, 27704K reserved, 16384K cma-reserved, 245748K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 31878 entries in 63 pages [ 0.000000] ftrace: allocated 63 pages with 6 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x660/0x844 with crng_init=0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000013] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000038] Switching to timer-based delay loop, resolution 41ns [ 0.000614] Console: colour dummy device 80x30 [ 0.000719] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000763] pid_max: default: 32768 minimum: 301 [ 0.001108] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001147] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002573] CPU: Testing write buffer coherency: ok [ 0.003027] /cpus/cpu@0 missing clock-frequency property [ 0.003074] /cpus/cpu@1 missing clock-frequency property [ 0.003118] /cpus/cpu@2 missing clock-frequency property [ 0.003166] /cpus/cpu@3 missing clock-frequency property [ 0.003184] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006038] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.006349] rcu: Hierarchical SRCU implementation. [ 0.007535] smp: Bringing up secondary CPUs ... [ 0.018774] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.031450] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.043738] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.044065] smp: Brought up 1 node, 4 CPUs [ 0.044125] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.044146] CPU: All CPU(s) started in HYP mode. [ 0.044166] CPU: Virtualization extensions available. [ 0.045485] devtmpfs: initialized [ 0.068038] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.068372] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.068410] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.070803] pinctrl core: initialized pinctrl subsystem [ 0.073009] NET: Registered protocol family 16 [ 0.077867] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.079320] thermal_sys: Registered thermal governor 'step_wise' [ 0.080649] No ATAGs? [ 0.081236] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.081277] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.171207] SCSI subsystem initialized [ 0.171524] usbcore: registered new interface driver usbfs [ 0.171598] usbcore: registered new interface driver hub [ 0.171681] usbcore: registered new device driver usb [ 0.172130] mc: Linux media interface: v0.10 [ 0.172185] videodev: Linux video capture interface: v2.00 [ 0.172268] pps_core: LinuxPPS API ver. 1 registered [ 0.172284] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.172314] PTP clock support registered [ 0.173206] Advanced Linux Sound Architecture Driver Initialized. [ 0.175648] clocksource: Switched to clocksource arch_sys_counter [ 1.350711] NET: Registered protocol family 2 [ 1.351852] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.351912] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.352001] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.352132] TCP: Hash tables configured (established 8192 bind 8192) [ 1.352860] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.353067] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.353690] NET: Registered protocol family 1 [ 1.355034] RPC: Registered named UNIX socket transport module. [ 1.355069] RPC: Registered udp transport module. [ 1.355090] RPC: Registered tcp transport module. [ 1.355110] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.357232] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 1.360836] Initialise system trusted keyrings [ 1.361205] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 1.376800] NFS: Registering the id_resolver key type [ 1.376920] Key type id_resolver registered [ 1.376943] Key type id_legacy registered [ 1.558155] Key type asymmetric registered [ 1.558188] Asymmetric key parser 'x509' registered [ 1.558382] bounce: pool size: 64 pages [ 1.558465] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.558487] io scheduler mq-deadline registered [ 1.558503] io scheduler kyber registered [ 1.560228] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.603090] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.628985] brd: module loaded [ 1.647002] loop: module loaded [ 1.657327] libphy: Fixed MDIO Bus: probed [ 1.659974] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 1.661131] libphy: sun4i_mii_bus: probed [ 1.664215] CAN device driver interface [ 1.668089] PPP generic driver version 2.4.2 [ 1.668383] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.668401] ehci-platform: EHCI generic platform driver [ 1.670908] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.670978] ohci-platform: OHCI generic platform driver [ 1.672744] usbcore: registered new interface driver usb-storage [ 1.672917] usbcore: registered new interface driver usbserial_generic [ 1.672971] usbserial: USB Serial support registered for generic [ 1.676928] sun6i-rtc 1c20400.rtc: registered as rtc1 [ 1.676964] sun6i-rtc 1c20400.rtc: RTC enabled [ 1.677599] i2c /dev entries driver [ 1.689050] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.694311] ledtrig-cpu: registered to indicate activity on CPUs [ 1.695088] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) from 24000000 (24 Mhz) [ 1.695527] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.696116] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.696965] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.697640] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 1.698080] sun8i-ce 1c15000.crypto: Register cbc(aes) [ 1.698491] sun8i-ce 1c15000.crypto: Register ecb(aes) [ 1.698833] sun8i-ce 1c15000.crypto: Register cbc(des3_ede) [ 1.699147] sun8i-ce 1c15000.crypto: Register ecb(des3_ede) [ 1.699461] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0 [ 1.701693] usbcore: registered new interface driver usbhid [ 1.701715] usbhid: USB HID core driver [ 1.712323] Initializing XFRM netlink socket [ 1.714237] NET: Registered protocol family 10 [ 1.716286] Segment Routing with IPv6 [ 1.716452] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.717362] NET: Registered protocol family 17 [ 1.717396] can: controller area network core [ 1.717501] NET: Registered protocol family 29 [ 1.717518] can: raw protocol [ 1.717534] can: broadcast manager protocol [ 1.717557] can: netlink gateway - max_hops=1 [ 1.718041] Key type dns_resolver registered [ 1.718454] Registering SWP/SWPB emulation handler [ 1.718976] registered taskstats version 1 [ 1.719164] Loading compiled-in X.509 certificates [ 1.754721] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 1.761733] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 1.764115] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator [ 1.770654] printk: console [ttyS0] disabled [ 1.770864] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 53, base_baud = 3000000) is a Allwinner sun4i [ 2.712560] printk: console [ttyS0] enabled [ 2.719009] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PI regulator [ 2.725878] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 274 [ 2.732500] sun4i-pinctrl 1c20800.pinctrl: pin-274 (1c28800.serial) status -517 [ 2.740030] sun4i-pinctrl 1c20800.pinctrl: could not request pin 274 (PI18) from group PI18 on device 1c20800.pinctrl [ 2.750895] dw-apb-uart 1c28800.serial: Error applying setting, reverse things back [ 2.762281] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 2.770701] libphy: sun4i_mii_bus: probed [ 2.775940] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.782741] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 236 [ 2.789510] sun4i-pinctrl 1c20800.pinctrl: pin-236 (1c20800.pinctrl:236) status -517 [ 2.799417] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 2.806304] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 232 [ 2.812940] sun4i-pinctrl 1c20800.pinctrl: pin-232 (1c0b000.ethernet) status -517 [ 2.820457] sun4i-pinctrl 1c20800.pinctrl: could not request pin 232 (PH8) from group PH8 on device 1c20800.pinctrl [ 2.830995] sun4i-emac 1c0b000.ethernet: Error applying setting, reverse things back [ 2.840231] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 2.847064] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 2.853509] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -517 [ 2.860885] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 2.871331] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse things back [ 2.891059] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 2.909938] vcc-3v3: supplied by regulator-dummy [ 2.916459] vdd-cpu: supplied by regulator-dummy [ 2.922503] vdd-sys: supplied by regulator-dummy [ 2.928481] dcdc4: supplied by regulator-dummy [ 2.934120] vcc-dram: supplied by regulator-dummy [ 2.939159] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER [ 2.946208] vcc-gmac-phy: supplied by vcc-3v3 [ 2.951826] dc5ldo: supplied by vcc-dram [ 2.956484] tv: Bringing 700000uV into 3300000-3300000uV [ 2.962526] tv: supplied by regulator-dummy [ 2.967411] aldo2: Bringing 2500000uV into 3300000-3300000uV [ 2.973777] aldo2: supplied by regulator-dummy [ 2.980091] avcc-pll: supplied by regulator-dummy [ 2.986783] eldo1: supplied by regulator-dummy [ 2.993091] eldo2: supplied by regulator-dummy [ 2.998540] vcc-pe: Bringing 1200000uV into 1800000-1800000uV [ 3.005546] vcc-pe: supplied by regulator-dummy [ 3.010825] vcc-sd-alt: Bringing 700000uV into 1800000-1800000uV [ 3.018197] vcc-sd-alt: supplied by regulator-dummy [ 3.025175] dldo2: supplied by regulator-dummy [ 3.031449] dldo3: supplied by regulator-dummy [ 3.037449] dldo4: supplied by regulator-dummy [ 3.042811] rtc_ldo: supplied by regulator-dummy [ 3.048735] ldo_io0: supplied by regulator-dummy [ 3.054492] ldo_io1: supplied by regulator-dummy [ 3.060174] axp20x-adc axp22x-adc: DMA mask not set [ 3.065539] random: fast init done [ 3.070723] axp20x-battery-power-supply axp20x-battery-power-supply: DMA mask not set [ 3.082198] axp20x-i2c 0-0034: AXP20X driver loaded [ 3.134422] sun4i-usb-phy 1c13400.phy: phy0 dr_mode=3 [ 3.142285] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 54, base_baud = 3000000) is a Allwinner sun4i [ 3.152776] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 3.155705] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, uses new timings mode [ 3.160802] libphy: sun4i_mii_bus: probed [ 3.293107] mmc0: new DDR MMC card at address 0001 [ 3.298815] mmcblk0: mmc0:0001 88A398 7.28 GiB [ 3.303764] mmcblk0boot0: mmc0:0001 88A398 partition 1 4.00 MiB [ 3.309426] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 66 MAC: 00:85:01:01:8c:a9 [ 3.310175] mmcblk0boot1: mmc0:0001 88A398 partition 2 4.00 MiB [ 3.318965] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 3.330257] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 3.330462] mmcblk0rpmb: mmc0:0001 88A398 partition 3 4.00 MiB, chardev (246:0) [ 3.336612] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 3.346239] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 3.349558] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supported [ 3.360706] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supported [ 3.367960] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 3.372925] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 3.379723] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 3.385379] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 3.391719] libphy: stmmac: probed [ 3.658206] ehci-platform 1c14000.usb: EHCI Host Controller [ 3.663816] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 3.671988] ehci-platform 1c14000.usb: irq 38, io mem 0x01c14000 [ 3.705629] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 3.712716] hub 1-0:1.0: USB hub found [ 3.716600] hub 1-0:1.0: 1 port detected [ 3.721735] ehci-platform 1c19000.usb: EHCI Host Controller [ 3.727362] ehci-platform 1c19000.usb: new USB bus registered, assigned bus number 2 [ 3.735367] ehci-platform 1c19000.usb: irq 40, io mem 0x01c19000 [ 3.765627] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 3.772612] hub 2-0:1.0: USB hub found [ 3.776443] hub 2-0:1.0: 1 port detected [ 3.781517] ehci-platform 1c1c000.usb: EHCI Host Controller [ 3.787136] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 3 [ 3.795120] ehci-platform 1c1c000.usb: irq 42, io mem 0x01c1c000 [ 3.826076] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 3.833052] hub 3-0:1.0: USB hub found [ 3.836879] hub 3-0:1.0: 1 port detected [ 3.935716] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 3.942352] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 4 [ 3.950315] ohci-platform 1c14400.usb: irq 39, io mem 0x01c14400 [ 4.030485] hub 4-0:1.0: USB hub found [ 4.034295] hub 4-0:1.0: 1 port detected [ 4.039433] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 4.046097] ohci-platform 1c19400.usb: new USB bus registered, assigned bus number 5 [ 4.054051] ohci-platform 1c19400.usb: irq 41, io mem 0x01c19400 [ 4.130504] hub 5-0:1.0: USB hub found [ 4.134309] hub 5-0:1.0: 1 port detected [ 4.139416] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 4.146079] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 6 [ 4.154052] ohci-platform 1c1c400.usb: irq 43, io mem 0x01c1c400 [ 4.160118] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 4.230513] hub 6-0:1.0: USB hub found [ 4.234321] hub 6-0:1.0: 1 port detected [ 4.247151] of_cfs_init [ 4.249727] of_cfs_init: OK [ 4.253219] ALSA device list: [ 4.256248] No soundcards found. [ 4.267277] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 4.286312] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 4.294485] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 4.304413] devtmpfs: mounted [ 4.312204] Freeing unused kernel memory: 1024K [ 4.355950] Run /sbin/init as init process [ 4.360053] with arguments: [ 4.360060] /sbin/init [ 4.360066] with environment: [ 4.360072] HOME=/ [ 4.360079] TERM=linux [ 4.395679] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 4.560141] systemd[1]: System time before build time, advancing clock. [ 4.597413] hub 1-1:1.0: USB hub found [ 4.601420] hub 1-1:1.0: 4 ports detected [ 4.629930] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 4.654346] systemd[1]: Detected architecture arm. [ 4.696532] systemd[1]: Set hostname to . [ 4.935715] usb 1-1.1: new full-speed USB device number 3 using ehci-platform [ 5.215669] usb 1-1.2: new full-speed USB device number 4 using ehci-platform [ 5.466321] systemd[1]: Queued start job for default target Graphical Interface. [ 5.475553] random: systemd: uninitialized urandom read (16 bytes read) [ 5.486350] systemd[1]: Created slice system-getty.slice. [ 5.495683] usb 1-1.4: new full-speed USB device number 5 using ehci-platform [ 5.526141] random: systemd: uninitialized urandom read (16 bytes read) [ 5.534731] systemd[1]: Created slice system-modprobe.slice. [ 5.575858] random: systemd: uninitialized urandom read (16 bytes read) [ 5.584520] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 5.627648] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 5.667630] systemd[1]: Created slice User and Session Slice. [ 5.706277] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 5.746132] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 5.786216] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 5.798276] systemd[1]: Reached target Local Encrypted Volumes. [ 5.836366] systemd[1]: Reached target Remote File Systems. [ 5.875860] systemd[1]: Reached target Slices. [ 5.907014] systemd[1]: Listening on fsck to fsckd communication Socket. [ 5.946325] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 5.996886] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 6.006173] systemd[1]: Listening on Journal Socket (/dev/log). [ 6.046896] systemd[1]: Listening on Journal Socket. [ 6.076923] systemd[1]: Listening on udev Control Socket. [ 6.116516] systemd[1]: Listening on udev Kernel Socket. [ 6.156758] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 6.170798] systemd[1]: Mounting POSIX Message Queue File System... [ 6.211807] systemd[1]: Mounting /sys/kernel/config... [ 6.251846] systemd[1]: Mounting Kernel Debug File System... [ 6.292552] systemd[1]: Mounting Kernel Trace File System... [ 6.334108] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 6.382863] systemd[1]: Starting Load Kernel Module drm... [ 6.422954] systemd[1]: Starting Load Kernel Module fuse... [ 6.446547] fuse: init (API version 7.32) [ 6.458303] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 6.474183] systemd[1]: Starting File System Check on Root Device... [ 6.527459] systemd[1]: Starting Journal Service... [ 6.543603] systemd[1]: Starting Load Kernel Modules... [ 6.558760] systemd[1]: Starting Coldplug All udev Devices... [ 6.581478] systemd[1]: Mounted POSIX Message Queue File System. [ 6.589295] systemd[1]: Mounted /sys/kernel/config. [ 6.600376] systemd[1]: Mounted Kernel Debug File System. [ 6.611472] systemd[1]: Mounted Kernel Trace File System. [ 6.624131] systemd[1]: Finished Create list of static device nodes for the current kernel. [ 6.709783] systemd[1]: modprobe@drm.service: Succeeded. [ 6.717453] systemd[1]: Finished Load Kernel Module drm. [ 6.757916] systemd[1]: modprobe@fuse.service: Succeeded. [ 6.764831] systemd[1]: Finished Load Kernel Module fuse. [ 6.806694] systemd[1]: Started Journal Service. [ 7.051293] EXT4-fs (mmcblk0p2): re-mounted. Opts: discard,errors=remount-ro [ 8.033505] Driver for 1-wire Dallas network protocol. [ 8.276268] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator [ 8.317484] wbec spi0.0: WBEC device added [ 8.366527] usbcore: registered new interface driver cp210x [ 8.372280] usbserial: USB Serial support registered for cp210x [ 8.378616] cp210x 1-1.1:1.0: cp210x converter detected [ 8.429833] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 8.436189] cp210x 1-1.2:1.0: cp210x converter detected [ 8.463623] usb 1-1.2: cp210x converter now attached to ttyUSB1 [ 8.470055] cp210x 1-1.4:1.0: cp210x converter detected [ 8.497042] usb 1-1.4: cp210x converter now attached to ttyUSB2 [ 8.517253] Bluetooth: Core ver 2.22 [ 8.521046] NET: Registered protocol family 31 [ 8.525515] Bluetooth: HCI device and connection manager initialized [ 8.532064] Bluetooth: HCI socket layer initialized [ 8.537050] Bluetooth: L2CAP socket layer initialized [ 8.542170] Bluetooth: SCO socket layer initialized [ 8.565271] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 8.582515] usbcore: registered new interface driver btusb [ 8.639747] Bluetooth: hci0: RTL: examining hci_ver=08 hci_rev=000f lmp_ver=08 lmp_subver=8723 [ 8.649728] Bluetooth: hci0: RTL: rom_version status=0 version=2 [ 8.655949] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723fu_fw.bin [ 8.665225] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723fu_config.bin [ 8.673159] Bluetooth: hci0: RTL: cfg_sz 14, total sz 37507 [ 8.676468] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 8.702712] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 8.993991] RTW: rtl8733bu v5.13.0.1-112-g10248f4f3.20230626_COEX20230616-330e [ 9.001402] RTW: rtl8733bu BT-Coex version = COEX20230616-330e [ 9.012758] RTW: [HALMAC]135 HALMAC_MAJOR_VER = 1 HALMAC_PROTOTYPE_VER = 6 HALMAC_MINOR_VER = 6 HALMAC_PATCH_VER = 39 [ 9.197574] RTW: hal_com_config_channel_plan chplan:0x7F [ 9.208593] wbec-power wbec-power.8.auto: DMA mask not set [ 9.208851] wbec-pwrkey wbec-pwrkey.7.auto: DMA mask not set [ 9.214786] wbec-watchdog wbec-watchdog.5.auto: DMA mask not set [ 9.214966] Bluetooth: hci0: RTL: fw version 0xd9b80b4f [ 9.221728] wbec-adc wbec-adc.3.auto: DMA mask not set [ 9.223477] input: wbec pwrkey as /devices/platform/soc/1c17000.spi/spi_master/spi0/spi0.0/wbec-pwrkey.7.auto/input/input0 [ 9.230560] wbec-gpio wbec-gpio.4.auto: DMA mask not set [ 9.250011] wbec-rtc wbec-rtc.6.auto: DMA mask not set [ 9.251987] iio-rescale vin-volt: using raw+scale source channel [ 9.274328] iio-rescale v33-volt: using raw+scale source channel [ 9.282811] wbec-rtc wbec-rtc.6.auto: registered as rtc0 [ 9.285149] iio-rescale v50-volt: using raw+scale source channel [ 9.302645] wbec-rtc wbec-rtc.6.auto: setting system clock to 2024-04-17T10:22:56 UTC (1713349376) [ 9.321822] iio-rescale vbus-debug-volt: using raw+scale source channel [ 9.331694] iio-rescale vbus-network-volt: using raw+scale source channel [ 9.350497] iio-rescale a1-volt: using raw+scale source channel [ 9.369715] iio-rescale a2-volt: using raw+scale source channel [ 9.383616] iio-rescale a3-volt: using raw+scale source channel [ 9.393938] RTW: rtw_ndev_init(wlan0) if1 mac_addr=98:03:cf:b1:d9:8c [ 9.398224] iio-rescale a4-volt: using raw+scale source channel [ 9.426862] RTW: rtw_ndev_init(wlan1) if2 mac_addr=9a:03:cf:b1:d9:8c [ 9.435284] usbcore: registered new interface driver rtl8733bu [ 9.955707] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SSDsc [ 10.110071] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: discard [ 10.327887] systemd-journald[140]: Received client request to flush runtime journal. [ 10.585721] random: crng init done [ 10.589173] random: 7 urandom warning(s) missed due to ratelimiting [ 12.206080] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 12.211458] Bluetooth: BNEP filters: protocol multicast [ 12.211490] Bluetooth: BNEP socket layer initialized [ 14.729321] dwmac-sun8i 1c50000.ethernet eth1: PHY [stmmac-1:00] driver [ICPlus IP101A/G] (irq=POLL) [ 14.740793] dwmac-sun8i 1c50000.ethernet eth1: No Safety Features support found [ 14.748318] dwmac-sun8i 1c50000.ethernet eth1: No MAC Management Counters available [ 14.756070] dwmac-sun8i 1c50000.ethernet eth1: PTP not supported by HW [ 14.767633] dwmac-sun8i 1c50000.ethernet eth1: configuring for phy/mii link mode [ 15.575847] start_addr=(0x0), end_addr=(0x20000), buffer_size=(0x20000), smp_number_max=(16384) [ 21.527200] RTW: assoc success [ 21.533290] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 21.541204] 1c29000.serial: ttyS4 at MMIO 0x1c29000 (irq = 131, base_baud = 3000000) is a Allwinner sun4i [ 28.376516] process '/usr/sbin/netplugd' started with executable stack [ 34.405911] vcc-gmac-phy: disabling [ 34.415872] dc5ldo: disabling [ 34.420245] dldo4: disabling [ 34.428701] vdd-sd-power: disabling [ 34.432263] vcc-sd: disabling [ 40.544888] Mass Storage Function, version: 2009/09/11 [ 40.550292] LUN: removable file: (no medium) [ 40.570333] using random self ethernet address [ 40.574834] using random host ethernet address [ 40.680291] dbg0: HOST MAC 1a:55:89:a2:69:44 [ 40.684879] dbg0: MAC 1a:55:89:a2:69:43 [ 47.335849] usb 3-1: new high-speed USB device number 2 using ehci-platform [ 47.624539] usb 3-1: USB disconnect, device number 2 [ 53.505896] usb 3-1: new high-speed USB device number 3 using ehci-platform [ 53.770411] usbcore: registered new interface driver cdc_ether [ 53.772964] usbcore: registered new interface driver option [ 53.782304] usbserial: USB Serial support registered for GSM modem (1-port) [ 53.790408] option 3-1:1.2: GSM modem (1-port) converter detected [ 53.797274] usb 3-1: GSM modem (1-port) converter now attached to ttyUSB3 [ 53.807297] rndis_host 3-1:1.0 usb0: register 'rndis_host' at usb-1c1c000.usb-1, RNDIS device, 36:e0:64:04:69:32 [ 53.817842] usbcore: registered new interface driver rndis_host [ 53.821125] option 3-1:1.4: GSM modem (1-port) converter detected [ 53.830585] usb 3-1: GSM modem (1-port) converter now attached to ttyUSB4 [ 53.838110] option 3-1:1.5: GSM modem (1-port) converter detected [ 53.849698] usb 3-1: GSM modem (1-port) converter now attached to ttyUSB5 [ 53.857024] option 3-1:1.3: GSM modem (1-port) converter detected [ 53.863907] usb 3-1: GSM modem (1-port) converter now attached to ttyUSB6 [ 79.130376] PPP BSD Compression module registered [ 79.154773] PPP Deflate Compression module registered