=~=~=~=~=~=~=~=~=~=~=~= MobaXterm log 2025.09.06 10:58:56 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01010104 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f383c .p0_mpwrdlctl= 0x3f3f3330 .p0_mpwldectrl0= 0x0008000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 44C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=3 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ....................................... U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01000103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f373c .p0_mpwrdlctl= 0x3f3f3330 .p0_mpwldectrl0= 0x0009000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 40C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=3 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ........... Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x82000000 ... ## Loading FIT strings to 0x82000028 ... ## Loading FIT struct to 0x82000100 ... Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x82000000 ... ## Loading FIT strings to 0x82000028 ... ## Loading FIT struct to 0x82000100 ... 11333688 bytes read in 512 ms (21.1 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x82000300 Data Size: 11324728 Bytes = 10.8 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 4581affae9501433b309790bd8c41cc21ab5e880 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x83000000 ... ## Loading FIT strings to 0x83000028 ... ## Loading FIT struct to 0x83000100 ... 57107 bytes read in 33 ms (1.6 MiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x83000400 Data Size: 47891 Bytes = 46.8 KiB Architecture: ARM Hash algo: sha1 Hash value: 50379d0c7fb9a54564de1311fee0fb398cef285a ## Verifying ... sha1+ Loading part 0 ... OK Kernel image @ 0x82000000 [ 0x000000 - 0xaccd38 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef8b000, end 9ef99b12 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb169 (root@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #2 SMP Wed Aug 7 14:43:03 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board init (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s31692 r8192 d21556 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=update_auto [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 503300K/524288K available (6144K kernel code, 645K rwdata, 1892K rodata, 7168K init, 250K bss, 20988K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x2b0/0x4bc with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000017] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000059] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002845] Console: colour dummy device 80x30 [ 0.002928] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002973] pid_max: default: 32768 minimum: 301 [ 0.003270] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003309] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.004602] CPU: Testing write buffer coherency: ok [ 0.005090] CPU0: update cpu_capacity 1024 [ 0.005127] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006322] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.006622] rcu: Hierarchical SRCU implementation. [ 0.007277] smp: Bringing up secondary CPUs ... [ 0.007315] smp: Brought up 1 node, 1 CPU [ 0.007340] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.007361] CPU: All CPU(s) started in SVC mode. [ 0.008272] devtmpfs: initialized [ 0.028864] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.029407] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.029460] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.029653] pinctrl core: initialized pinctrl subsystem [ 0.031782] NET: Registered protocol family 16 [ 0.032395] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034864] thermal_sys: Registered thermal governor 'step_wise' [ 0.035157] cpuidle: using governor menu [ 0.219600] vdd1p1: supplied by regulator-dummy [ 0.232202] vdd3p0: supplied by regulator-dummy [ 0.244743] cpu: supplied by regulator-dummy [ 0.257318] vddsoc: supplied by regulator-dummy [ 0.630438] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.630480] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.631097] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.631874] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.633410] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.633451] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.680347] mxs-dma 1804000.dma-apbh: initialized [ 0.685966] SCSI subsystem initialized [ 0.686533] usbcore: registered new interface driver usbfs [ 0.686665] usbcore: registered new interface driver hub [ 0.686792] usbcore: registered new device driver usb [ 0.687654] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.687782] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.688723] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.689410] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.689537] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.690126] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.690769] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.690893] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.691487] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.693171] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.693560] i2c i2c-1: IMX I2C adapter registered [ 0.694396] pps_core: LinuxPPS API ver. 1 registered [ 0.694426] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.694486] PTP clock support registered [ 0.696940] clocksource: Switched to clocksource mxc_timer1 [ 0.717406] NET: Registered protocol family 2 [ 0.719003] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.719085] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.719199] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.719362] TCP: Hash tables configured (established 4096 bind 4096) [ 0.719557] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.719627] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.719970] NET: Registered protocol family 1 [ 0.721157] RPC: Registered named UNIX socket transport module. [ 0.721195] RPC: Registered udp transport module. [ 0.721217] RPC: Registered tcp transport module. [ 0.721237] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.644216] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 1.648229] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 1.659448] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.661224] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.900314] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.900355] io scheduler mq-deadline registered [ 1.900377] io scheduler kyber registered [ 1.912907] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.912963] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.917522] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 28, base_baud = 5000000) is a IMX [ 2.560613] random: fast init done [ 2.610196] printk: console [ttymxc0] enabled [ 2.616840] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 66, base_baud = 5000000) is a IMX [ 2.627786] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 67, base_baud = 5000000) is a IMX [ 2.671041] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 2.679088] random: crng init done [ 2.710549] brd: module loaded [ 2.731763] loop: module loaded [ 2.735281] at24 5-0050: supply vcc not found, using dummy regulator [ 2.747024] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 2.754007] at24 6-0050: supply vcc not found, using dummy regulator [ 2.765584] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 2.774098] libphy: Fixed MDIO Bus: probed [ 2.781512] pps pps0: new PPS source ptp0 [ 2.823485] libphy: fec_enet_mii_bus: probed [ 2.829628] fec 20b4000.ethernet eth0: registered PHC device 0 [ 2.957753] pps pps1: new PPS source ptp1 [ 2.964284] libphy: fec_enet_mii_bus: probed [ 2.973283] fec 2188000.ethernet eth1: registered PHC device 1 [ 2.980322] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.986881] ehci-mxc: Freescale On-Chip EHCI Host driver [ 2.992740] usbcore: registered new interface driver cdc_acm [ 2.998586] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 3.007042] usbcore: registered new interface driver usb-storage [ 3.056125] rtc rtc0: invalid alarm value: 2025-09-06T00:70:00 [ 3.062479] rtc-pcf8563 4-0051: registered as rtc0 [ 3.079458] rtc-pcf8563 4-0051: setting system clock to 2025-09-06T08:04:06 UTC (1757145846) [ 3.098341] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1 [ 3.104832] i2c /dev entries driver [ 3.114918] imx6ul-pinctrl 20e0000.pinctrl: pin MX6UL_PAD_SD1_DATA1 already requested by watchdog; cannot claim for watchdog_6x [ 3.126539] imx6ul-pinctrl 20e0000.pinctrl: pin-114 (watchdog_6x) status -22 [ 3.133716] imx6ul-pinctrl 20e0000.pinctrl: could not request pin 114 (MX6UL_PAD_SD1_DATA1) from group wdggrp_6x on device 20e0000.pinctrl [ 3.146307] gpio-wdt watchdog_6x: Error applying setting, reverse things back [ 3.153623] gpio-wdt: probe of watchdog_6x failed with error -22 [ 3.161875] sdhci: Secure Digital Host Controller Interface driver [ 3.168222] sdhci: Copyright(c) Pierre Ossman [ 3.172600] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.187973] ledtrig-cpu: registered to indicate activity on CPUs [ 3.196017] usbcore: registered new interface driver usbhid [ 3.201757] usbhid: USB HID core driver [ 3.208969] NET: Registered protocol family 17 [ 3.218153] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA [ 3.225396] Registering SWP/SWPB emulation handler [ 3.231113] registered taskstats version 1 [ 3.260971] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 3.272640] of_cfs_init [ 3.275230] of_cfs_init: OK [ 3.294439] Freeing unused kernel memory: 7168K [ 3.299356] Run /init as init process [ 3.321668] mmc0: new DDR MMC card at address 0001 [ 3.334257] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 3.340003] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 3.346349] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB mount: mounting none on /sys/kernel/debug failed: No such file or directory [ 3.367354] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (248:0) mount: mounting none on /dev/pts [ 3.386281] mmcblk0: p1 p2 p3 p4 < p5 p6 > failed: No such file or directory Run busybox watchdog for /dev/watchdog Run busybox watchdog for /dev/watchdog0 Run busybox watchdog for /dev/watchdog1 Run busybox watchdog for /dev/watchdog2 Boot mode: update_auto Board is WB6, loading ci_hdrc_imx module [ 3.674974] imx_usb 2184000.usb: No over current polarity defined [ 3.690267] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 3.695218] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 3.727282] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 3.733501] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 3.741959] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.749354] usb usb1: Product: EHCI Host Controller [ 3.754288] usb usb1: Manufacturer: Linux 5.10.35-wb169 ehci_hcd [ 3.760426] usb usb1: SerialNumber: ci_hdrc.0 [ 3.767558] hub 1-0:1.0: USB hub found [ 3.771537] hub 1-0:1.0: 1 port detected [ 3.781061] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.786007] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 3.817112] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.823472] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 3.831928] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.839324] usb usb2: Product: EHCI Host Controller [ 3.844257] usb usb2: Manufacturer: Linux 5.10.35-wb169 ehci_hcd [ 3.850446] usb usb2: SerialNumber: ci_hdrc.1 [ 3.857528] hub 2-0:1.0: USB hub found [ 3.861416] hub 2-0:1.0: 1 port detected [ 4.137111] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.227130] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 4.399423] usb 1-1: New USB device found, idVendor=090c, idProduct=2000, bcdDevice=11.00 [ 4.407809] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.415120] usb 1-1: Product: USB DISK [ 4.419034] usb 1-1: Manufacturer: SMI Corporation [ 4.427461] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.434592] scsi host0: usb-storage 1-1:1.0 [ 4.438967] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 4.447236] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 4.456419] hub 2-1:1.0: USB hub found [ 4.460423] hub 2-1:1.0: 4 ports detected [ 4.777069] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ 4.928404] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00 [ 4.936807] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.944235] usb 2-1.1: Product: 802.11n WLAN Adapter [ 4.949249] usb 2-1.1: Manufacturer: Realtek [ 4.953529] usb 2-1.1: SerialNumber: 00e04c000001 /init: line 325: can't create /sys/class/usb_role/*/role: nonexistent directory Load modules for USB to work Waiting for USB to settle (1/10) [ 5.936323] scsi 0:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4 [ 5.948985] sd 0:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) [ 5.959288] sd 0:0:0:0: [sda] Write Protect is off [ 5.966118] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.980287] sda: sda1 [ 5.987621] sd 0:0:0:0: [sda] Attached SCSI removable disk Looking for update .fit on /dev/sda... Looking for update .fit on /dev/sda1... Will use wb6_update_FACTORYRESET.fit from USB Flash Drive ############################################################################## FACTORY RESET REQUESTED This WILL destroy ALL YOUR DATA: configuration, scripts, files in home directory! If you are ABSOLUTELY SURE that you want to reset Wiren Board to factory condition, hold the FW button for 4 seconds. If you will not do it in 10 seconds, the controller will reboot without firmware update. If you want to perform a regular firmware update, rename FIT file to "wbX_update.fit" without "factory-reset" suffix. ############################################################################## o.... Factory reset is confirmed! =============================================================================== Sat Sep 6 08:04:17 UTC 2025: started update from /disk/wb6_update_FACTORYRESET.fit =============================================================================== Description: WirenBoard firmware update Compatible device: contactless,imx6ul-wirenboard670 Firmware version: 202508111043 Firmware compatible: +single-rootfs +fit-factory-reset +force-repartition +repartition-ramsize-fix +fit-immutable-support +wb8-debug-network-update-fix +wrong-ab-layout-fix +update-from-cloud Release name: wb-2507 Release suite: stable Release target: wb6/bullseye Release repo prefix: Time of creation: Mon Aug 11 10:43:52 UTC 2025 =============================================================================== >>> Checking SHA1 hash of install PROGRESS: 0% PROGRESS: 0% >>> SHA1 hash of install ok >>> Requested factory reset will be performed by firmware itself 32+0 records in 32+0 records out 16384 bytes (16 kB, 16 KiB) copied, 0.0140432 s, 1.2 MB/s >>> Firmware seems to be compatible with this controller >>> Extracting install script >>> Running install script >>> Console logging enabled; tempfile /tmp/tmp.G7Qq9f, final file /disk/wb-console.log will be written on exit >>> Reading uboot env offset/size from device tree... >>> Could not read uboot-env-offset from device tree. Keeping old fw_env.config from rootfs >>> Extend tmpfs size to whole RAM >>> Remount tmpfs in /tmp with size=498M >>> Maybe update factoryreset.fit to fix tmpfs size issue at 512M RAM (with emmc update) [ 20.093633] EXT4-fs (mmcblk0p6): recovery complete [ 20.100108] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) >>> Factoryreset.fit already includes a fix for the 512MB RAM repartition issue (repartition-ramsize-fix compatibility) 32+0 records in 32+0 records out 16384 bytes (16 kB, 16 KiB) copied, 0.0178266 s, 919 kB/s >>> Firmware seems to be compatible with this controller >>> Wiping data partition (factory reset) [ 22.153454] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) [ 33.767091] vref-3v3: disabling >>> Checking SHA1 hash of rootfs PROGRESS: 0% PROGRESS: 2% PROGRESS: 4% PROGRESS: 7% PROGRESS: 9% PROGRESS: 12% PROGRESS: 15% PROGRESS: 17% PROGRESS: 20% PROGRESS: 22% PROGRESS: 25% PROGRESS: 27% PROGRESS: 30% PROGRESS: 32% PROGRESS: 35% PROGRESS: 37% PROGRESS: 40% PROGRESS: 42% PROGRESS: 45% PROGRESS: 48% PROGRESS: 50% PROGRESS: 53% PROGRESS: 55% PROGRESS: 58% PROGRESS: 60% PROGRESS: 63% PROGRESS: 65% PROGRESS: 68% PROGRESS: 70% PROGRESS: 73% PROGRESS: 75% PROGRESS: 78% PROGRESS: 80% PROGRESS: 83% PROGRESS: 86% PROGRESS: 88% PROGRESS: 91% PROGRESS: 93% PROGRESS: 96% PROGRESS: 98% PROGRESS: 100% >>> SHA1 hash of rootfs ok >>> rootfs is valid, installing firmware update >>> Enlarging first rootfs partition >>> Mounting partition before calling e2fsck to renew mount time [ 74.669210] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) >>> Checking and repairing filesystem on /dev/mmcblk0p2 >>> Temp toolpath: /tmp/tmp.qpqnQl rootfs: 27566/116736 files (0.3% non-contiguous), 167297/262144 blocks tune2fs 1.46.2 (28-Feb-2021) Setting time filesystem last checked to Sat Sep 6 08:06:25 2025 >>> Backing up old MBR (and partition table) 1+0 records in 1+0 records out 512 bytes copied, 0.00211892 s, 242 kB/s >>> Creating a new parition table >>> New disk dump will be saved in /tmp/tmp.k68uaY Partition #2 contains a ext4 signature. Partition #5 contains a swap signature. Partition #6 contains a ext4 signature. Re-reading the partition table failed.: Device or resource busy >>> Unmounting /mnt/data and saving its mountpoint [ 142.972919] mmcblk0: p1 p2 p3 p4 < p5 p6 > >>> Restoring mount of /dev/mmcblk0p6 to /mnt/data [ 143.009856] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) >>> Expanding filesystem on this partition e2fsck 1.46.2 (28-Feb-2021) rootfs: clean, 27566/116736 files, 167297/262144 blocks resize2fs 1.46.2 (28-Feb-2021) Overwriting existing filesystem; this can be undone using the command: e2undo /tmp/tmp.HI3Gfz /dev/mmcblk0p2 Resizing the filesystem on /dev/mmcblk0p2 to 524287 (4k) blocks. The filesystem on /dev/mmcblk0p2 is now 524287 (4k) blocks long. >>> Repartition is done! >>> rootfs enlarged! >>> Configuring environment for repartitioned eMMC >>> Will install to /dev/mmcblk0p2 [ 146.917507] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) >>> Cleaning up /dev/mmcblk0p2 >>> Cleaning up using rsync >>> Mounting /dev/mmcblk0p2 at /tmp/tmp.hEnpOP [ 157.790615] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) >>> Extracting files to new rootfs /tmp/tmp.hEnpOP / PROGRESS: 0% PROGRESS: 1% PROGRESS: 3% PROGRESS: 3% PROGRESS: 5% PROGRESS: 6% PROGRESS: 7% PROGRESS: 9% PROGRESS: 10% PROGRESS: 11% PROGRESS: 12% PROGRESS: 12% PROGRESS: 14% PROGRESS: 15% PROGRESS: 16% PROGRESS: 18% PROGRESS: 19% PROGRESS: 20% PROGRESS: 21% PROGRESS: 23% PROGRESS: 23% PROGRESS: 24% PROGRESS: 25% PROGRESS: 26% PROGRESS: 28% PROGRESS: 29% PROGRESS: 30% PROGRESS: 32% PROGRESS: 33% PROGRESS: 34% PROGRESS: 36% PROGRESS: 37% PROGRESS: 38% PROGRESS: 39% PROGRESS: 41% PROGRESS: 42% PROGRESS: 43% PROGRESS: 45% PROGRESS: 46% PROGRESS: 47% PROGRESS: 47% PROGRESS: 48% PROGRESS: 49% PROGRESS: 49% PROGRESS: 51% PROGRESS: 52% PROGRESS: 53% PROGRESS: 54% PROGRESS: 55% PROGRESS: 56% PROGRESS: 57% PROGRESS: 57% PROGRESS: 58% PROGRESS: 59% PROGRESS: 60% PROGRESS: 60% PROGRESS: 61% PROGRESS: 62% PROGRESS: 63% PROGRESS: 64% PROGRESS: 65% PROGRESS: 66% PROGRESS: 67% PROGRESS: 68% PROGRESS: 69% PROGRESS: 71% PROGRESS: 72% PROGRESS: 72% PROGRESS: 74% PROGRESS: 75% PROGRESS: 75% PROGRESS: 76% PROGRESS: 78% PROGRESS: 79% PROGRESS: 80% PROGRESS: 80% PROGRESS: 82% PROGRESS: 83% PROGRESS: 84% PROGRESS: 84% PROGRESS: 84% PROGRESS: 85% PROGRESS: 86% PROGRESS: 86% PROGRESS: 86% PROGRESS: 86% PROGRESS: 87% PROGRESS: 88% PROGRESS: 88% PROGRESS: 89% PROGRESS: 90% PROGRESS: 91% PROGRESS: 91% PROGRESS: 92% PROGRESS: 92% PROGRESS: 92% PROGRESS: 92% PROGRESS: 93% PROGRESS: 93% PROGRESS: 95% PROGRESS: 97% PROGRESS: 99% PROGRESS: 99% PROGRESS: 100% / >>> Recovering device certificates [ 260.773712] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null) >>> Mount /dev, /proc and /sys to rootfs /tmp/tmp.hEnpOP >>> Running post-install scripts >>> > Processing /tmp/tmp.hEnpOP/usr/lib/wb-image-update/postinst/10update-u-boot Trying to install u-boot using u-boot-install-wb from new rootfs Das U-Boot installer for Wiren Board You are about to install U-boot image '/usr/lib/u-boot/mx6ul_wirenboard6/u-boot-with-spl.imx' on '/dev/mmcblk0' (platform wb6) Force installation requested Writing U-boot image '/usr/lib/u-boot/mx6ul_wirenboard6/u-boot-with-spl.imx' on '/dev/mmcblk0' (options 'bs=512 seek=2') 831+1 records in 831+1 records out 425824 bytes (426 kB, 416 KiB) copied, 0.46888 s, 908 kB/s Syncing device >>> > Processing /tmp/tmp.hEnpOP/usr/lib/wb-image-update/postinst/10update-wbec-firmware 32+0 records in 32+0 records out 16384 bytes (16 kB, 16 KiB) copied, 0.0155963 s, 1.1 MB/s This Wiren Board does not have WBEC, exiting >>> Unmounting /dev, /proc and /sys from rootfs /tmp/tmp.hEnpOP >>> Checking, /tmp/tmp.424FD3/.wb-restore/factoryreset.fit supports features: single-rootfs wb8-debug-network-update-fix wrong-ab-layout-fix >>> Storing this update as factory FIT to use as bootlet (supports single-rootfs wb8-debug-network-update-fix wrong-ab-layout-fix) >>> Old factory FIT will be kept as factoryreset.original.fit and will still be used to restore firmware >>> Copying /disk/wb6_update_FACTORYRESET.fit to factory default location as requested >>> Switching to new rootfs >>> Done! >>> Unmounting rootfs >>> Reboot system [ 302.357703] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 302.368729] ci_hdrc ci_hdrc.0: remove, state 1 [ 302.373265] usb usb1: USB disconnect, device number 1 [ 302.378440] usb 1-1: USB disconnect, device number 2 [ 302.506612] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 302.512200] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=0x01 driverbyte=0x00 [ 302.549565] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 302.589295] ci_hdrc ci_hdrc.1: remove, state 1 [ 302.593786] usb usb2: USB disconnect, device number 1 [ 302.599033] usb 2-1: USB disconnect, device number 2 [ 302.604015] usb 2-1.1: USB disconnect, device number 3 [ 302.615783] ci_hdrc ci_hdrc.1: USB bus 2 deregistered [ 302.621331] imx2-wdt 20bc000.watchdog: Device shutdown: Expect reboot! [ 302.628102] reboot: Restarting system U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01030107 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f393c .p0_mpwrdlctl= 0x3f3f3331 .p0_mpwldectrl0= 0x0009000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 57C Reset cause: WDOG Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=1 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Saving Environment to MMC... Writing to MMC(1)... OK Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ................................................ Checking if there is a USB storage with update file wb6_update.fit dev: usb1_vbus @ regulator@0 starting USB... Bus usb@2184000: USB EHCI 1.00 Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 2 USB Device(s) found scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80 USB device not accepting new address (error=22) 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SMI Rev: 1100 Prod: USB DISK Type: Removable Hard Disk Capacity: 7680.0 MB = 7.5 GB (15728640 x 512) Failed to load 'wb6_update.fit' 1 bytes read in 5 ms (0 Bytes/s) ############################## # Detected USB Flash drive with update file # Filename: wb6_update_FACTORYRESET.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## No USB update detected, continuing boot 323 bytes read in 3 ms (104.5 KiB/s) Importing environment from 0x82000000... Checking if uenvcmd is set ... Running default loadzimage ... 6304488 bytes read in 275 ms (21.9 MiB/s) MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK Reading overlays list from eMMC Reading factory fdt name from eMMC Loading factory fdt imx6ul-wirenboard680 47686 bytes read in 7 ms (6.5 MiB/s) 485 bytes read in 4 ms (118.2 KiB/s) Applying DT overlay wb6-nogsm 597 bytes read in 4 ms (145.5 KiB/s) Applying DT overlay wb6-wifi-rtl8723bu 509 bytes read in 4 ms (124 KiB/s) Applying DT overlay wb6-noradio 334 bytes read in 4 ms (81.1 KiB/s) Applying DT overlay wb6-eth1 254 bytes read in 3 ms (82 KiB/s) Applying DT overlay temp-industrial Applying extra overlay Booting from mmc ... Kernel image @ 0x82000000 [ 0x000000 - 0x6032e8 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 9ef77000, end 9ef99fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35-wb178 (root@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Wed Jul 9 19:05:13 UTC 2025 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.8.0 (i.MX6UL/ULL) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9f000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait ro [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 489360K/524288K available (8192K kernel code, 728K rwdata, 2776K rodata, 1024K init, 283K bss, 18544K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x234/0x3dc with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000059] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002765] Console: colour dummy device 80x30 [ 0.002827] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002864] pid_max: default: 32768 minimum: 301 [ 0.003259] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003296] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.004989] CPU: Testing write buffer coherency: ok [ 0.006207] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.007092] devtmpfs: initialized [ 0.024947] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.025456] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025500] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.026871] pinctrl core: initialized pinctrl subsystem [ 0.028875] NET: Registered protocol family 16 [ 0.031087] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033032] thermal_sys: Registered thermal governor 'step_wise' [ 0.033353] cpuidle: using governor menu [ 0.216755] vdd1p1: supplied by regulator-dummy [ 0.228484] vdd3p0: supplied by regulator-dummy [ 0.240245] cpu: supplied by regulator-dummy [ 0.252032] vddsoc: supplied by regulator-dummy [ 0.589561] No ATAGs? [ 0.589621] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.589643] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.590240] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present! [ 0.590904] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.592412] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000 [ 0.592451] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.635040] mxs-dma 1804000.dma-apbh: initialized [ 0.640267] SCSI subsystem initialized [ 0.640758] usbcore: registered new interface driver usbfs [ 0.640878] usbcore: registered new interface driver hub [ 0.640989] usbcore: registered new device driver usb [ 0.641803] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.641930] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.643378] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL) [ 0.644267] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.644389] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.644973] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL) [ 0.645666] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.645787] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.646373] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL) [ 0.647951] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 0.648311] i2c i2c-1: IMX I2C adapter registered [ 0.649032] mc: Linux media interface: v0.10 [ 0.649138] videodev: Linux video capture interface: v2.00 [ 0.649266] pps_core: LinuxPPS API ver. 1 registered [ 0.649287] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.649336] PTP clock support registered [ 0.649952] Advanced Linux Sound Architecture Driver Initialized. [ 0.652062] clocksource: Switched to clocksource mxc_timer1 [ 0.669745] NET: Registered protocol family 2 [ 0.671035] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.671127] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.671232] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.671337] TCP: Hash tables configured (established 4096 bind 4096) [ 0.671526] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.671580] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.671899] NET: Registered protocol family 1 [ 0.672945] RPC: Registered named UNIX socket transport module. [ 0.672982] RPC: Registered udp transport module. [ 0.673000] RPC: Registered tcp transport module. [ 0.673017] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.674087] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.676908] Initialise system trusted keyrings [ 0.677370] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.688983] NFS: Registering the id_resolver key type [ 0.689062] Key type id_resolver registered [ 0.689083] Key type id_legacy registered [ 0.929067] Key type asymmetric registered [ 0.929106] Asymmetric key parser 'x509' registered [ 0.929227] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.929249] io scheduler mq-deadline registered [ 0.929266] io scheduler kyber registered [ 0.941109] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.941157] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.945112] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX [ 1.607779] printk: console [ttymxc0] enabled [ 1.614224] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX [ 1.657981] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.665408] random: fast init done [ 1.669359] random: crng init done [ 1.709167] brd: module loaded [ 1.727317] loop: module loaded [ 1.730816] at24 5-0050: supply vcc not found, using dummy regulator [ 1.742304] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.749289] at24 6-0050: supply vcc not found, using dummy regulator [ 1.760657] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 1.773124] libphy: Fixed MDIO Bus: probed [ 1.780117] pps pps0: new PPS source ptp0 [ 1.820475] libphy: fec_enet_mii_bus: probed [ 1.825957] fec 20b4000.ethernet ethFEC0: registered PHC device 0 [ 1.952794] pps pps1: new PPS source ptp1 [ 1.959373] libphy: fec_enet_mii_bus: probed [ 1.968070] fec 2188000.ethernet ethFEC1: registered PHC device 1 [ 1.975171] PPP generic driver version 2.4.2 [ 1.979854] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.986493] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.992268] usbcore: registered new interface driver usb-storage [ 1.998520] usbcore: registered new interface driver usbserial_generic [ 2.005181] usbserial: USB Serial support registered for generic [ 2.054544] rtc rtc0: invalid alarm value: 2025-09-06T00:70:00 [ 2.060805] rtc-pcf8563 4-0051: registered as rtc0 [ 2.077650] rtc-pcf8563 4-0051: setting system clock to 2025-09-06T08:09:17 UTC (1757146157) [ 2.096278] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1 [ 2.102797] i2c /dev entries driver [ 2.109482] lm75 4-0048: supply vs not found, using dummy regulator [ 2.121145] lm75 4-0048: hwmon0: sensor 'lm75b' [ 2.241304] sdhci: Secure Digital Host Controller Interface driver [ 2.247585] sdhci: Copyright(c) Pierre Ossman [ 2.251958] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.265902] ledtrig-cpu: registered to indicate activity on CPUs [ 2.273707] usbcore: registered new interface driver usbhid [ 2.279306] usbhid: USB HID core driver [ 2.294602] Initializing XFRM netlink socket [ 2.299011] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA [ 2.307308] NET: Registered protocol family 10 [ 2.315093] Segment Routing with IPv6 [ 2.319226] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.327318] NET: Registered protocol family 17 [ 2.332488] Key type dns_resolver registered [ 2.340779] registered taskstats version 1 [ 2.345567] Loading compiled-in X.509 certificates [ 2.368286] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 2.380236] of_cfs_init [ 2.383045] of_cfs_init: OK [ 2.390903] ALSA device list: [ 2.393947] No soundcards found. [ 2.397672] Waiting for root device /dev/mmcblk0p2... [ 2.407430] mmc0: new DDR MMC card at address 0001 [ 2.413206] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.418122] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 2.424586] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 2.430810] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (245:0) [ 2.441625] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 2.470596] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.479127] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.490700] devtmpfs: mounted [ 2.498913] Freeing unused kernel memory: 1024K [ 2.504355] Run /sbin/init as init process [ 2.923943] systemd[1]: systemd 247.3-7+deb11u7 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 2.948388] systemd[1]: Detected architecture arm. [ 2.954452] systemd[1]: Detected first boot. Welcome to Debian GNU/Linux 11 (bullseye)! [ 2.993866] systemd[1]: Set hostname to . [ 3.013102] systemd[1]: Initializing machine ID from random generator. [ 5.016918] systemd[1]: Invalid unit wpa_supplicant-nl80211@.service symlink multi-user.target.wants/wpa_supplicant-nl80211@.service. [ 5.048144] systemd[1]: Invalid unit wpa_supplicant@.service symlink multi-user.target.wants/wpa_supplicant@.service. [ 5.061744] systemd[1]: Invalid unit wpa_supplicant-wired@.service symlink multi-user.target.wants/wpa_supplicant-wired@.service. [ 5.075796] systemd[1]: Failed to populate /etc with preset unit settings, ignoring: Read-only file system [ 5.984513] systemd[1]: Queued start job for default target Graphical Interface. [ 5.999749] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 6.035615] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 6.080290] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 6.129608] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. [ 6.178388] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 6.214459] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password ts to Console Directory Watch. [ 6.254051] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Ruests to Wall Directory Watch. [ 6.293677] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 6.306714] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 6.343210] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 6.374019] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 6.412766] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 6.445379] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 6.484422] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 6.559400] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 6.569017] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 6.603714] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 6.640387] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 6.675854] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 6.714890] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 6.732158] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 6.783963] systemd[1]: Mounting /sys/kernel/config... Mounting /sys/kernel/config... [ 6.838489] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 6.883220] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. [ 6.904664] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of stodes for the current kernel... [ 6.963874] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 6.994760] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 7.035681] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 7.054599] fuse: init (API version 7.32) [ 7.064061] systemd[1]: Starting File System Check on Root Device... Starting File System Check on Root Device... [ 7.115537] systemd[1]: Starting Journal Service... Starting Journal Service... [ 7.163437] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 7.220994] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 7.334936] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 7.379280] systemd[1]: Mounted /sys/kernel/config. [ OK ] Mounted /sys/kernel/config. [ 7.411615] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 7.453554] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st nodes for the current kernel. [ 7.554590] systemd[1]: modprobe@drm.service: Succeeded. [ 7.577791] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 7.634834] systemd[1]: modprobe@fuse.service: Succeeded. [ 7.662597] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 7.692507] systemd[1]: Finished File System Check on Root Device. [ OK ] Finished File System Check on Root Device. [ 7.735718] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. [ 7.792667] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 7.840518] systemd[1]: Started File System Check Daemon to report status. [ OK ] Started File System Check Daemon to report status. [ 7.925582] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 8.008632] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 8.057858] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ 8.163707] EXT4-fs (mmcblk0p2): re-mounted. Opts: discard,errors=remount-ro [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Apply Kernel Variables. Starting Load/Save Random Seed... Starting Create System Users... [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Reached target Local File Systems (Pre). [ OK ] Set up automount mnt-sdcard.automount. Starting Rule-based Managefor Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ 10.901395] Driver for 1-wire Dallas network protocol. [ 10.927339] gpio-68 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 11.032872] gpio-11 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 11.202195] w1_master_driver w1_bus_master1: Attaching one wire slave 28.0921404e7720 crc c9 [ 11.676570] w1_master_driver w1_bus_master1: Attaching one wire slave 28.0a21405a13ba crc 6d [ OK ] Found device /dev/ttymxc0. [ 11.911372] fec 20b4000.ethernet eth1: renamed from ethFEC0 [ 12.323739] w1_master_driver w1_bus_master1: Attaching one wire slave 28.0621422a9bbb crc eb [ 12.671646] fec 2188000.ethernet eth0: renamed from ethFEC1 [ 12.700386] imx_usb 2184000.usb: No over current polarity defined [ 12.796035] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 12.800976] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 13.002148] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 13.028801] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 13.037153] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 13.044414] usb usb1: Product: EHCI Host Controller [ 13.049300] usb usb1: Manufacturer: Linux 5.10.35-wb178 ehci_hcd [ 13.055330] usb usb1: SerialNumber: ci_hdrc.0 [ 13.284008] hub 1-0:1.0: USB hub found [ 13.322594] hub 1-0:1.0: 1 port detected [ 13.406391] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 13.489694] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 13.632217] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 13.665802] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 13.674169] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 13.681418] usb usb2: Product: EHCI Host Controller [ 13.686336] usb usb2: Manufacturer: Linux 5.10.35-wb178 ehci_hcd [ 13.692369] usb usb2: SerialNumber: ci_hdrc.1 [ 13.822261] usb usb1-port1: over-current condition [ 13.954395] hub 2-0:1.0: USB hub found [ 13.972169] hub 2-0:1.0: 1 port detected [ 13.985533] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 14.294224] usb 1-1: New USB device found, idVendor=090c, idProduct=2000, bcdDevice=11.00 [ 14.302541] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 14.309716] usb 1-1: Product: USB DISK [ 14.313507] usb 1-1: Manufacturer: SMI Corporation [ 14.392164] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 14.549536] usb-storage 1-1:1.0: USB Mass Storage device detected [ 14.632904] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 14.641137] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 14.792587] hub 2-1:1.0: USB hub found [ 14.796477] scsi host0: usb-storage 1-1:1.0 [ 14.842159] hub 2-1:1.0: 4 ports detected [ 15.232175] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc [ 15.433718] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00 [ 15.442161] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 15.449506] usb 2-1.1: Product: 802.11n WLAN Adapter [ 15.454511] usb 2-1.1: Manufacturer: Realtek [ 15.458788] usb 2-1.1: SerialNumber: 00e04c000001 [ OK ] Found device /dev/mmcblk0p5. [ 16.056921] scsi 0:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4 [ 16.102390] sd 0:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) [ 16.130290] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 16.138223] sd 0:0:0:0: [sda] Write Protect is off [ 16.152517] Bluetooth: Core ver 2.22 [ 16.156275] NET: Registered protocol family 31 [ 16.160731] Bluetooth: HCI device and connection manager initialized [ 16.193365] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ OK ] Found device [ 16.253384] Bluetooth: HCI socket layer initialized /dev/mmcblk0p6. [ 16.265187] sda: sda1 [ 16.307261] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 16.327582] Bluetooth: L2CAP socket layer initialized [ 16.358366] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 16.365225] Bluetooth: SCO socket layer initialized [ 16.480105] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 16.488333] usbcore: registered new interface driver btusb [ 16.497566] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [ 16.509499] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 16.515720] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin [ 16.525949] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin [ 16.532567] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2 [ 16.541809] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496 [ 17.129331] RTL871X: module init start [ 17.133208] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40 [ 17.309243] RTL871X: rtw_ndev_init(wlan0) [ OK ] Listening on Load/Save RF itch S[ 17.325768] RTL871X: rtw_ndev_init(wlan1) tatus /dev/rfkill Watch. [ 17.337350] usbcore: registered new interface driver rtl8723bu [ 17.343272] RTL871X: module init ret=0 [ 17.358488] Bluetooth: hci0: RTL: fw version 0x0e2f9f73 Activating swap /dev/mmcblk0p5... Starting File System Check on /dev/mmcblk0p6... Starting Load/Save RF Kill Switch Status... [ 18.145320] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SSDsc [ 18.195002] usbcore: registered new interface driver rtl8xxxu [ OK ] Activated swap /dev/mmcblk0p5. [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Finished File System Check on /dev/mmcblk0p6. [ OK ] Reached target Swap. Mounting /mnt/data... [ 19.151038] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: discard [ OK ] Mounted /mnt/data. Mounting /var/log... [ OK ] Mounted /var/log. [ OK ] Reached target Local File Systems. Starting Flush Journal to Persistent Storage... Starting prepare mounts and symlinks to config files... [ 19.454075] systemd-journald[122]: Received client request to flush runtime journal. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished prepare mounts and symlinks to config files. Starting Create Volatile Files and Directories... [ OK ] Finished Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onliata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on fcgiwrap Socket. [ OK ] Listening on KNX Daemon (socket). [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Bluetooth service... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting Network Manager... Starting Remove Stale Onlit4 Metadata Check Snapshots... Starting Authorization Manager... Starting User Login Management... [ OK ] Started watch config files. Starting Initialize Wiren Board Device Tree overlays... Starting initialize filesystems at first boot... Starting WPA supplicant... [ 25.734424] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 25.739763] Bluetooth: BNEP filters: protocol multicast [ OK ] Started Bluetooth service. [ 25.815309] Bluetooth: BNEP socket layer initialized [ OK ] Started WPA supplicant. [ OK ] Started Authorization Manager. [ OK ] Reached target Bluetooth. Starting Modem Manager... Starting Hostname Service... [ OK ] Started User Login Management. [ OK ] Started Hostname Service. [ OK ] Started Modem Manager. [ OK ] Started Network Manager. Starting Network Manager Wait Online... Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ 32.172326] SMSC LAN8710/LAN8720 2188000.ethernet-2:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet-2:00, irq=POLL) [ 32.485048] Micrel KSZ8081 or KSZ8091 2188000.ethernet-2:03: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=2188000.ethernet-2:03, irq=POLL) [ 34.332552] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 35.782183] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 44.617687] RTL871X: assoc success [ 44.632740] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ OK ] Finished Network Manager Wait Online. [** ] (1 of 3) A start job is running forems at first boot (31s / no limit) [* ] (1 of 3) A start job is running forems at first boot (31s / no limit) [** ] (1 of 3) A start job is running forems at first boot (32s / no limit) [*** ] (2 of 3) A start job is running fora Check Snapshots (45s / no limit) [ *** ] (2 of 3) A start job is running fora Check Snapshots (45s / no limit) [ *** ] (2 of 3) A start job is running fora Check Snapshots (48s / no limit) [ ***] (3 of 3) A start job is running forice Tree overlays (48s / 3min 18s) [ **] (3 of 3) A start job is running forice Tree overlays (49s / 3min 18s) [ *] (3 of 3) A start job is running forice Tree overlays (49s / 3min 18s) [ **] (1 of 3) A start job is running forems at first boot (37s / no limit) [ 56.727844] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 224, base_baud = 5000000) is a IMX [ ***] (1 of 3) A start job is running forems at first boot (38s / no limit) [ *** ] (1 of 3) A start job is running forems at first boot (40s / no limit) [ *** ] (2 of 3) A start job is running fora Check Snapshots (53s / no limit) [*** ] (2 of 3) A start job is running fora Check Snapshots (54s / no limit) [** ] (2 of 3) A start job is running fora Check Snapshots (54s / no limit) [* ] (3 of 3) A start job is running forice Tree overlays (55s / 3min 18s) [** ] (3 of 3) A start job is running forice Tree overlays (55s / 3min 18s) [*** ] (3 of 3) A start job is running forice Tree overlays (56s / 3min 18s) [ *** ] (1 of 3) A start job is running forems at first boot (43s / no limit) [ *** ] (1 of 3) A start job is running forems at first boot (44s / no limit) [ ***] (1 of 3) A start job is running forems at first boot (44s / no limit) [ **] (2 of 3) A start job is running fora Check Snapshots (58s / no limit) [ *] (2 of 3) A start job is running fora Check Snapshots (58s / no limit) [ OK ] Finished Initialize Wiren Board Device Tree overlays. Starting Raise network interfaces... [ OK ] Started Network connectionrvice for Wiren Board devices. Starting Power on GSM modem... Starting KNXD Configurator for Wiren Board... [ OK ] Finished Raise network interfaces. [ **] (1 of 4) A start job is running for on GSM modem (1min 2s / 2min 28s) [ ***] (2 of 4) A start job is running forems at first boot (50s / no limit) [ *** ] (2 of 4) A start job is running forems at first boot (50s / no limit) [ *** ] (2 of 4) A start job is running forems at first boot (50s / no limit) [ INFO ] Skipped Power on GSM modem. [*** ] (1 of 3) A start job is running forems at first boot (53s / no limit) Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [** ] (1 of 3) A start job is running forems at first boot (55s / no limit) [* ] (1 of 3) A start job is running forems at first boot (56s / no limit) [** ] (2 of 3) A start job is running foreck Snapshots (1min 9s / no limit) [*** ] (2 of 3) A start job is running foreck Snapshots (1min 9s / no limit) [ *** ] (2 of 3) A start job is running forck Snapshots (1min 10s / no limit) [ *** ] (3 of 3) A start job is running for Wiren Board (1min 10s / no limit) [ ***] (3 of 3) A start job is running for Wiren Board (1min 11s / no limit) [ **] (3 of 3) A start job is running for Wiren Board (1min 11s / no limit) [ *] (1 of 3) A start job is running forems at first boot (59s / no limit) [ **] (1 of 3) A start job is running forms at first boot (1min / no limit) [ ***] (1 of 3) A start job is running forms at first boot (1min / no limit) [ *** ] (2 of 3) A start job is running forck Snapshots (1min 13s / no limit) [ *** ] (2 of 3) A start job is running forck Snapshots (1min 14s / no limit) [ OK ] Finished Remove Stale Onliext4 Metadata Check Snapshots. [*** ] (1 of 2) A start job is running forat first boot (1min 4s / no limit) [** ] (2 of 2) A start job is running for Wiren Board (1min 17s / no limit) [* ] (2 of 2) A start job is running for Wiren Board (1min 17s / no limit) [** ] (2 of 2) A start job is running for Wiren Board (1min 18s / no limit) [*** ] (1 of 2) A start job is running forat first boot (1min 6s / no limit) [ *** ] (1 of 2) A start job is running forat first boot (1min 6s / no limit) [ *** ] (1 of 2) A start job is running forat first boot (1min 7s / no limit) [ ***] (2 of 2) A start job is running for Wiren Board (1min 20s / no limit) [ **] (2 of 2) A start job is running for Wiren Board (1min 20s / no limit) [ OK ] Finished initialize filesystems at first boot. [ OK ] Reached target First Boot Complete. [ OK ] Reached target Network. Starting Avahi mDNS/DNS-SD Stack... Starting dnsmasq - A lightDHCP and caching DNS server... Starting Access point and rver for Wi-Fi and Ethernet... Starting KNX Daemon... Starting Mosquitto MQTT Broker... Starting Network Time Service... Starting OpenBSD Secure Shell server... Starting Commit a transient machine-id on disk... Starting Permit User Sessions... Starting MQTT Driver for ADC... Starting MQTT Driver for GPIO-controlled switches... [ OK ] Started MQTT Driver for serial devices. [ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA. [ OK ] Started KNX Daemon. [ OK ] Finished KNXD Configurator for Wiren Board. [ INFO ] Skipped dnsmasq - A lightwt DHCP and caching DNS server. [ INFO ] Skipped Access point and aserver for Wi-Fi and Ethernet. [ OK ] Started Network Time Service. [ OK ] Finished Commit a transient machine-id on disk. [ OK ] Finished Permit User Sessions. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Mosquitto MQTT Broker. [ OK ] Reached target Network is Online. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started Getty on tty1. Starting LSB: Brings up/down network automatically... Starting A high performanc and a reverse proxy server... [ OK ] Started Serial Getty on ttymxc0. [ OK ] Reached target Login Prompts. Starting Wiren Board Cloud Agent (default)... [ OK ] Started Wiren Board modbus devices manager. [ OK ] Started one-click diagnost generating archive with data. [ OK ] Started Wiren Board configuration editor backend. [ OK ] Started Wiren Board database logger. Starting Wiren Board MQTT to IEC 60870-5-104 gateway... [ OK ] Started Wiren Board MQTT KNX bridge. [ OK ] Started Wiren Board journald to MQTT gateway. [ OK ] Started Wiren Board MQTT to Modbus gateway. [ OK ] Started metrics sender. [ OK ] Started Virtual MQTT devicr Network Manager connections. Starting Wiren Board MQTT to OPC UA gateway... [ OK ] Started MQTT Rule engine for Wiren Board. Starting Compensation of se-tree (with opposite sign)... [ OK ] Started Wiren Board firmware update service. [ OK ] Started MQTT Driver for GPIO-controlled switches. [ OK ] Started Wiren Board MQTT to IEC 60870-5-104 gateway. [ OK ] Started Wiren Board MQTT to OPC UA gateway. Debian GNU/Linux 11 wirenboard-AFXJFKDT ttymxc0 wirenboard-AFXJFKDT login: [ 104.586577] process '/usr/sbin/netplugd' started with executable stack wirenboard-AFXJFKDT login: Password: Login incorrect wirenboard-AFXJFKDT login: Password: Login incorrect wirenboard-AFXJFKDT login: ^H^H^H^H^H^H^H^H^H^H^H^H Password: Login incorrect wirenboard-AFXJFKDT login: Password: Login incorrect wirenboard-AFXJFKDT login: root Password: Login incorrect Maximum number of tries exceeded (5) Debian GNU/Linux 11 wirenboard-AFXJFKDT ttymxc0 wirenboard-AFXJFKDT login: root Password: _ _ _ __ _(_)_ __ ___ _ __ | |__ ___ __ _ _ __ __| | \ \ /\ / / | '__/ _ \ '_ \| '_ \ / _ \ / _` | '__/ _` | \ V V /| | | | __/ | | | |_) | (_) | (_| | | | (_| | \_/\_/ |_|_| \___|_| |_|_.__/ \___/ \__,_|_| \__,_| Welcome to Wiren Board 6.8.2 (s/n AFXJFKDT), release wb-2507 (as stable) Linux wirenboard-AFXJFKDT 5.10.35-wb178 #1 Wed Jul 9 19:05:13 UTC 2025 armv7l GNU/Linux System load: 1.24 1.55 1.24Up time: 11 min Memory usage: 24% of 494M Usage of /: 33% of 2.0G /mnt/data: 11% of 4.7G eth0 ip: 192.168.0.154 root@wirenboard-AFXJFKDT:~# root@wirenboard-AFXJFKDT:~# root@wirenboard-AFXJFKDT:~# root@wirenboard-AFXJFKDT:~# [ 75 U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01010103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f373c .p0_mpwrdlctl= 0x3f3f3330 .p0_mpwldectrl0= 0x0008000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 51C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ............................ U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01000103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f373c .p0_mpwrdlctl= 0x3f3f3230 .p0_mpwldectrl0= 0x0008000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 52C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ........................................... U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01000103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f363c .p0_mpwrdlctl= 0x3f3f3230 .p0_mpwldectrl0= 0x0008000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 52C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode .......................................... U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01000103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f363c .p0_mpwrdlctl= 0x3f3f3230 .p0_mpwldectrl0= 0x0008000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 51C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode .......................................... U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01000103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f363c .p0_mpwrdlctl= 0x3f3f3230 .p0_mpwldectrl0= 0x0008000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 50C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode .......................................... U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01010103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f373c .p0_mpwrdlctl= 0x3f3f3331 .p0_mpwldectrl0= 0x0009000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 50C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1 0 ## Info: input data size = 4285 = 0x10BD switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode .......................................... U-Boot SPL 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) DRAM init ok, rows:15, ncs:1, size: 512MB .p0_mpdgctrl0= 0x01000103 .p0_mpdgctrl1= 0x0e3f0e3f .p0_mprddlctl= 0x3f3f373c .p0_mpwrdlctl= 0x3f3f3230 .p0_mpwldectrl0= 0x0008000a .p0_mpwldectrl1= 0x000b000b Trying to boot from MMC1 Warning - USDHC2 controller not supporting U-Boot 2021.10-wb1.7.2-00063-g54396ff3fc5 (Jul 17 2025 - 11:10:00 +0000) CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 50C Reset cause: POR Model: Wiren Board rev. 6.1 (i.MX6UL) Board: Wiren Board MX6UL DRAM: 512 MiB MMC: FSL_SDHC: 1 In: serial Out: serial Err: serial Loading Environment from MMC... OK Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/8188 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 1