U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode ............. Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file 1 bytes read in 3 ms (0 Bytes/s) ############################## # Detected microSD card with update file # Filename: wb_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file 1 bytes read in 4 ms (0 Bytes/s) ############################## # Detected microSD card with update file # Filename: wb_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file 1 bytes read in 3 ms (0 Bytes/s) ############################## # Detected microSD card with update file # Filename: wb_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file 1 bytes read in 3 ms (0 Bytes/s) ############################## # Detected microSD card with update file # Filename: wb_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file 1 bytes read in 3 ms (0 Bytes/s) ############################## # Detected microSD card with update file # Filename: wb_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## U-Boot SPL 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) DRAM: 1024 MiB Trying to boot from MMC2 U-Boot 2021.10-wb1.1.1-g4c04347f3e (Feb 03 2022 - 14:48:16 +0000) CPU: Allwinner R40 (SUN8I 1701) Model: Wiren Board rev. 7.2.0 (A40i) I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from MMC... OK In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program ## Info: input data size = 43 = 0x2B bootcount=0 mmcpart=2 upgrade_available=0 Environment size: 43/131068 bytes ## Resetting to default environment ## Info: input data size = 43 = 0x2B Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device eMMC found on device 1 Press FW button to enter firmware update mode Entering firmware update mode. Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting kernel ## Loading FIT header to 0x42000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1Extracting DTB ## Loading FIT header to 0x43000000 ... ** File not found .wb-restore/factoryreset.fit ** Read failed: -1zimage: Bad magic! ERROR: Failed to enter update mode! ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt Checking if there is a microSD card with update file 1 bytes read in 4 ms (0 Bytes/s) ############################## # Detected microSD card with update file # Filename: wb_update.fit # Press a FW key if you want to update firmware from this file # or wait 3 seconds to boot normally. ############################## USB update procedure start Checking if ubootenv part is present ## Loading FIT header to 0x42000000 ... ## Loading FIT strings to 0x42000028 ... ## Loading FIT struct to 0x42000100 ... Can't find subimage 'ubootenv' Extracting kernel ## Loading FIT header to 0x42000000 ... ## Loading FIT strings to 0x42000028 ... ## Loading FIT struct to 0x42000100 ... 7770848 bytes read in 361 ms (20.5 MiB/s) Description: Update kernel Type: Kernel Image Compression: uncompressed Data Start: 0x42000300 Data Size: 7761888 Bytes = 7.4 MiB Architecture: ARM OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 58eb2949fba68971ec9b6f42197daab785109ac1 ## Verifying ... sha1+ Loading part 0 ... OK Extracting DTB ## Loading FIT header to 0x43000000 ... ## Loading FIT strings to 0x43000028 ... ## Loading FIT struct to 0x43000100 ... 63880 bytes read in 29 ms (2.1 MiB/s) Description: Update DTB Type: Flat Device Tree Compression: uncompressed Data Start: 0x43000540 Data Size: 54344 Bytes = 53.1 KiB Architecture: ARM Hash algo: sha1 Hash value: 88cb690e62d3e2fbe97df37350c2ee8c8abab757 ## Verifying ... sha1+ Loading part 0 ... OK Kernel image @ 0x42000000 [ 0x000000 - 0x766fe0 ] ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Device Tree to 49fef000, end 49fff447 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35+ (webconn@webconn-laptop) (arm-linux-gnueabihf-gcc (Debian 10.3.0-8) 10.3.0, GNU ld (GNU Binutils for Debian) 2.37.90.20220123) #6 SMP Wed Feb 9 22:20:01 MSK 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Wiren Board rev. 7.2.0 (A40i) [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x7ec00000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 15 pages/cpu s31180 r8192 d22068 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyS0,115200 bootmode=update_auto bootmode=sdupdate,wb_update.fit [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1007360K/1048576K available (7168K kernel code, 657K rwdata, 1524K rodata, 4096K init, 398K bss, 24832K reserved, 16384K cma-reserved, 245748K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x4f8 with crng_init=0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000023] Switching to timer-based delay loop, resolution 41ns [ 0.000358] Console: colour dummy device 80x30 [ 0.000418] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000442] pid_max: default: 32768 minimum: 301 [ 0.000618] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.000638] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002109] CPU: Testing write buffer coherency: ok [ 0.002849] /cpus/cpu@0 missing clock-frequency property [ 0.002915] /cpus/cpu@1 missing clock-frequency property [ 0.002971] /cpus/cpu@2 missing clock-frequency property [ 0.003027] /cpus/cpu@3 missing clock-frequency property [ 0.003054] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004018] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.004213] rcu: Hierarchical SRCU implementation. [ 0.005018] smp: Bringing up secondary CPUs ... [ 0.015906] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.026901] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.037801] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.037926] smp: Brought up 1 node, 4 CPUs [ 0.037958] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.037968] CPU: All CPU(s) started in HYP mode. [ 0.037976] CPU: Virtualization extensions available. [ 0.038718] devtmpfs: initialized [ 0.055786] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.056036] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.056061] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.058443] pinctrl core: initialized pinctrl subsystem [ 0.059821] NET: Registered protocol family 16 [ 0.060939] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.063165] thermal_sys: Registered thermal governor 'step_wise' [ 0.064047] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.064075] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.114671] SCSI subsystem initialized [ 0.114954] usbcore: registered new interface driver usbfs [ 0.115012] usbcore: registered new interface driver hub [ 0.115071] usbcore: registered new device driver usb [ 0.118016] clocksource: Switched to clocksource arch_sys_counter [ 0.118594] FS-Cache: Loaded [ 0.118956] CacheFiles: Loaded [ 0.131615] NET: Registered protocol family 2 [ 0.132231] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.132280] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.132356] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.132476] TCP: Hash tables configured (established 8192 bind 8192) [ 0.133045] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.133239] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.133789] NET: Registered protocol family 1 [ 0.135112] RPC: Registered named UNIX socket transport module. [ 0.135137] RPC: Registered udp transport module. [ 0.135151] RPC: Registered tcp transport module. [ 0.135163] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.420979] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.423655] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.436639] NFS: Registering the id_resolver key type [ 0.436692] Key type id_resolver registered [ 0.436704] Key type id_legacy registered [ 0.436759] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.437514] bounce: pool size: 64 pages [ 0.437569] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.437581] io scheduler mq-deadline registered [ 0.437591] io scheduler kyber registered [ 0.438255] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 0.557558] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.577256] loop: module loaded [ 0.588355] libphy: Fixed MDIO Bus: probed [ 0.588975] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 0.589701] libphy: sun4i_mii_bus: probed [ 0.593363] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.593394] ehci-platform: EHCI generic platform driver [ 0.594253] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.594291] ohci-platform: OHCI generic platform driver [ 0.595013] usbcore: registered new interface driver cdc_acm [ 0.595025] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 0.595093] usbcore: registered new interface driver usb-storage [ 0.597928] sun6i-rtc 1c20400.rtc: registered as rtc1 [ 0.598085] sun6i-rtc 1c20400.rtc: RTC enabled [ 0.598668] i2c /dev entries driver [ 0.602052] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.605542] ledtrig-cpu: registered to indicate activity on CPUs [ 0.606017] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) from 24000000 (24 Mhz) [ 0.606358] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 0.606852] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 0.607002] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 0.607135] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority [ 0.607252] sun8i-ce 1c15000.crypto: Register cbc(aes) [ 0.607392] sun8i-ce 1c15000.crypto: Register ecb(aes) [ 0.607509] sun8i-ce 1c15000.crypto: Register cbc(des3_ede) [ 0.607618] sun8i-ce 1c15000.crypto: Register ecb(des3_ede) [ 0.608548] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0 [ 0.611444] iio-rescale a1-volt: using raw+scale source channel [ 0.611787] iio-rescale a2-volt: using raw+scale source channel [ 0.612065] iio-rescale a3-volt: using raw+scale source channel [ 0.612308] iio-rescale vin-volt: using raw+scale source channel [ 0.615825] NET: Registered protocol family 10 [ 0.617003] Segment Routing with IPv6 [ 0.617101] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 0.617827] NET: Registered protocol family 17 [ 0.617935] Key type dns_resolver registered [ 0.618062] Registering SWP/SWPB emulation handler [ 0.618171] registered taskstats version 1 [ 0.642355] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO [ 0.648105] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.648760] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator [ 0.650570] printk: console [ttyS0] disabled [ 0.650690] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 52, base_baud = 1500000) is a Allwinner sun4i [ 1.504324] printk: console [ttyS0] enabled [ 1.510484] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PI regulator [ 1.517286] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 274 [ 1.523938] sun4i-pinctrl 1c20800.pinctrl: pin-274 (1c28800.serial) status -517 [ 1.531373] sun4i-pinctrl 1c20800.pinctrl: could not request pin 274 (PI18) from group PI18 on device 1c20800.pinctrl [ 1.542177] dw-apb-uart 1c28800.serial: Error applying setting, reverse things back [ 1.550355] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 1.559586] libphy: sun4i_mii_bus: probed [ 1.565365] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 1.572204] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 236 [ 1.578838] sun4i-pinctrl 1c20800.pinctrl: pin-236 (1c20800.pinctrl:236) status -517 [ 1.588653] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 1.595445] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 232 [ 1.602203] sun4i-pinctrl 1c20800.pinctrl: pin-232 (1c0b000.ethernet) status -517 [ 1.609726] sun4i-pinctrl 1c20800.pinctrl: could not request pin 232 (PH8) from group PH8 on device 1c20800.pinctrl [ 1.620261] sun4i-emac 1c0b000.ethernet: Error applying setting, reverse things back [ 1.628406] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 1.635213] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 1.641710] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -517 [ 1.649036] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 1.659388] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse things back [ 1.679869] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 1.693993] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0034/axp221-pek/input/input0 [ 1.714590] vcc-3v3: supplied by regulator-dummy [ 1.720086] vdd-cpu: supplied by regulator-dummy [ 1.725465] vdd-sys: supplied by regulator-dummy [ 1.730903] dcdc4: supplied by regulator-dummy [ 1.735891] vcc-dram: Bringing 1500000uV into 1350000-1350000uV [ 1.742357] vcc-dram: supplied by regulator-dummy [ 1.747182] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER [ 1.754109] vcc-gmac-phy: supplied by vcc-3v3 [ 1.758973] random: fast init done [ 1.762815] dc5ldo: supplied by vcc-dram [ 1.767394] tv: Bringing 700000uV into 3300000-3300000uV [ 1.773403] tv: supplied by regulator-dummy [ 1.778307] aldo2: Bringing 2500000uV into 3300000-3300000uV [ 1.784581] aldo2: supplied by regulator-dummy [ 1.790369] avcc-pll: supplied by regulator-dummy [ 1.795914] eldo1: supplied by regulator-dummy [ 1.801239] eldo2: supplied by regulator-dummy [ 1.806321] vcc-pe: Bringing 1200000uV into 1800000-1800000uV [ 1.813068] vcc-pe: supplied by regulator-dummy [ 1.818177] vcc-sd-alt: Bringing 700000uV into 1800000-1800000uV [ 1.824984] vcc-sd-alt: supplied by regulator-dummy [ 1.830581] dldo2: supplied by regulator-dummy [ 1.835739] dldo3: supplied by regulator-dummy [ 1.840925] dldo4: supplied by regulator-dummy [ 1.845701] rtc_ldo: supplied by regulator-dummy [ 1.851104] ldo_io0: supplied by regulator-dummy [ 1.856450] ldo_io1: supplied by regulator-dummy [ 1.867124] axp20x-adc axp22x-adc: DMA mask not set [ 1.873392] axp20x-i2c 0-0034: AXP20X driver loaded [ 1.908756] rtc rtc0: Power loss detected, invalid time [ 1.914454] rtc-pcf85063 2-0051: registered as rtc0 [ 1.928783] rtc rtc0: Power loss detected, invalid time [ 1.934041] rtc-pcf85063 2-0051: setting system clock to 2025-12-20T13:23:52 UTC (1766237032) [ 1.948413] lm75 2-0048: supply vs not found, using dummy regulator [ 1.959188] lm75 2-0048: hwmon0: sensor 'lm75b' [ 1.986771] at24 3-0050: supply vcc not found, using dummy regulator [ 1.994513] at24 3-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 2.008028] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, uses new timings mode [ 2.010742] i2c-gpio i2c_eeprom1: using lines 48 (SDA) and 49 (SCL) [ 2.026608] at24 4-0050: supply vcc not found, using dummy regulator [ 2.034309] at24 4-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write [ 2.050555] i2c-gpio i2c_eeprom2: using lines 46 (SDA) and 47 (SCL) [ 2.057089] sun4i-usb-phy 1c13400.phy: phy0 dr_mode=3 [ 2.064216] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 53, base_baud = 1500000) is a Allwinner sun4i [ 2.074380] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator [ 2.082283] libphy: sun4i_mii_bus: probed [ 2.102292] mmc0: new DDR MMC card at address 0001 [ 2.107788] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 2.112685] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 2.118962] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 2.125145] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (248:0) [ 2.135243] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 2.223392] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 65 MAC: e8:eb:1b:3f:a9:ce [ 2.232303] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 2.238681] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 2.247111] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 2.253215] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supported [ 2.260460] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supported [ 2.267673] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 2.272648] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 2.279439] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 2.285091] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 2.291316] libphy: stmmac: probed [ 2.550084] ehci-platform 1c14000.usb: EHCI Host Controller [ 2.555685] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 2.563749] ehci-platform 1c14000.usb: irq 37, io mem 0x01c14000 [ 2.597989] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 2.604812] hub 1-0:1.0: USB hub found [ 2.608664] hub 1-0:1.0: 1 port detected [ 2.613403] ehci-platform 1c19000.usb: EHCI Host Controller [ 2.619026] ehci-platform 1c19000.usb: new USB bus registered, assigned bus number 2 [ 2.626938] ehci-platform 1c19000.usb: irq 39, io mem 0x01c19000 [ 2.657988] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 2.664694] hub 2-0:1.0: USB hub found [ 2.668512] hub 2-0:1.0: 1 port detected [ 2.673182] ehci-platform 1c1c000.usb: EHCI Host Controller [ 2.678802] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 3 [ 2.686696] ehci-platform 1c1c000.usb: irq 41, io mem 0x01c1c000 [ 2.718803] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 2.725491] hub 3-0:1.0: USB hub found [ 2.729305] hub 3-0:1.0: 1 port detected [ 2.828091] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 2.834720] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 4 [ 2.842668] ohci-platform 1c14400.usb: irq 38, io mem 0x01c14400 [ 2.922628] hub 4-0:1.0: USB hub found [ 2.926414] hub 4-0:1.0: 1 port detected [ 2.931128] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 2.937753] ohci-platform 1c19400.usb: new USB bus registered, assigned bus number 5 [ 2.945665] ohci-platform 1c19400.usb: irq 40, io mem 0x01c19400 [ 3.022650] hub 5-0:1.0: USB hub found [ 3.026435] hub 5-0:1.0: 1 port detected [ 3.031131] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 3.037754] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 6 [ 3.045579] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 3.052735] ohci-platform 1c1c400.usb: irq 42, io mem 0x01c1c400 [ 3.132613] hub 6-0:1.0: USB hub found [ 3.136402] hub 6-0:1.0: 1 port detected [ 3.141383] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator [ 3.151462] of_cfs_init [ 3.152574] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 3.153968] of_cfs_init: OK [ 3.183731] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 3.197278] Freeing unused kernel memory: 4096K [ 3.218156] Run /init as init process [ 3.227695] mmc1: host does not support reading read-only switch, assuming write-enable [ 3.239303] mmc1: new high speed SDHC card at address 0001 mount: mounting none on /dev/pts failed: No such file or directo[ 3.245583] mmcblk1: mmc1:0001 asdfg 29.3 GiB ry [ 3.256446] mmcblk1: p1 Boot mode: sdupdate,wb_update.fit Board is WB7 Looking for update .fit on /dev/mmcblk1p1... [ 3.652914] sunxi-mmc 1c0f000.mmc: data error, sending stop command [ 3.659251] sunxi-mmc 1c0f000.mmc: send stop command failed [ 3.664931] sunxi-mmc 1c0f000.mmc: data error, sending stop command [ 3.671214] sunxi-mmc 1c0f000.mmc: send stop command failed [ 3.676878] sunxi-mmc 1c0f000.mmc: data error, sending stop command [ 3.683183] sunxi-mmc 1c0f000.mmc: send stop command failed [ 3.688872] sunxi-mmc 1c0f000.mmc: data error, sending stop command [ 3.695140] sunxi-mmc 1c0f000.mmc: send stop command failed [ 3.700806] sunxi-mmc 1c0f000.mmc: data error, sending stop command [ 3.707073] sunxi-mmc 1c0f000.mmc: send stop command failed [ 5.114317] mmc1: card never left busy state [ 5.118617] mmc1: tried to HW reset card, got error -110 [ 5.130428] blk_update_request: I/O error, dev mmcblk1, sector 2048 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 0 [ 5.130458] mmc1: card 0001 removed [ 5.141148] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write [ 5.153425] FAT-fs (mmcblk1p1): Directory bread(block 32768) failed [ 5.159728] FAT-fs (mmcblk1p1): Directory bread(block 32769) failed [ 5.165994] FAT-fs (mmcblk1p1): Directory bread(block 32770) failed [ 5.172271] FAT-fs (mmcblk1p1): Directory bread(block 32771) failed [ 5.178550] FAT-fs (mmcblk1p1): Directory bread(block 32772) failed [ 5.184814] FAT-fs (mmcblk1p1): Directory bread(block 32773) failed [ 5.191097] FAT-fs (mmcblk1p1): Directory bread(block 32774) failed [ 5.197361] FAT-fs (mmcblk1p1): Directory bread(block 32775) failed [ 5.203640] FAT-fs (mmcblk1p1): Directory bread(block 32776) failed [ 5.209922] FAT-fs (mmcblk1p1): Directory bread(block 32777) failed [ 5.309832] mmc1: host does not support reading read-only switch, assuming write-enable [ 5.321284] mmc1: new high speed SDHC card at address 0001 [ 5.327504] mmcblk1: mmc1:0001 asdfg 29.3 GiB [ 5.333468] mmcblk1: p1 [ 5.336479] debugfs: Directory 'mmcblk1' with parent 'block' already present! [ 6.223880] FAT-fs (mmcblk1p1): unable to read boot sector to mark fs as dirty BusyBox v1.22.1 (Debian 1:1.22.0-19+deb9u2) built-in shell (ash) Enter 'help' for a list of built-in commands. sh: can't access tty; job control turned off ~ # [ 33.758027] vcc-gmac-phy: disabling [ 33.761854] dc5ldo: disabling [ 33.765136] dldo4: disabling