U-Boot SPL 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
DRAM init ok, rows:15, ncs:1, size: 512MB
.p0_mpdgctrl0 = 0x01120112
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3d3f
.p0_mpwrdlctl = 0x3f3f3836
.p0_mpwldectrl0 = 0x0008000a
.p0_mpwldectrl1 = 0x000b000b
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 65C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 512 MiB
MMC: FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Loading Environment from MMC... OK
Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program
## Info: input data size = 100 = 0x64
bootcount=0
mmcpart=3
uenvcmd=env default -a; setenv mmcpart 3; saveenv; reset
upgrade_available=0
Environment size: 100/8188 bytes
## Resetting to default environment
## Info: input data size = 100 = 0x64
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
## Info: input data size = 4285 = 0x10BD
switch to partitions #0, OK
mmc1(part 0) is current device
eMMC found on device 1
Press FW button to enter firmware update mode
................................................
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
Bus usb@2184000: USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found
scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80
USB device not accepting new address (error=22)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
No storage devices, perhaps not 'usb start'ed..?
No USB update detected, continuing boot
322 bytes read in 3 ms (104.5 KiB/s)
Importing environment from 0x82000000...
Checking if uenvcmd is set ...
Running uenvcmd ...
## Resetting to default environment
Saving Environment to MMC... Writing to MMC(1)... OK
resetting ...
U-Boot SPL 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
DRAM init ok, rows:15, ncs:1, size: 512MB
.p0_mpdgctrl0 = 0x0114010f
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3b3d
.p0_mpwrdlctl = 0x3f3f3835
.p0_mpwldectrl0 = 0x00080008
.p0_mpwldectrl1 = 0x00090009
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 67C
Reset cause: WDOG
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 512 MiB
MMC: FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Loading Environment from MMC... OK
Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program
## Info: input data size = 43 = 0x2B
bootcount=0
mmcpart=3
upgrade_available=0
Environment size: 43/8188 bytes
## Resetting to default environment
## Info: input data size = 43 = 0x2B
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
## Info: input data size = 4285 = 0x10BD
switch to partitions #0, OK
mmc1(part 0) is current device
eMMC found on device 1
Press FW button to enter firmware update mode
................................................
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
Bus usb@2184000: USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found
scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80
USB device not accepting new address (error=22)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
No storage devices, perhaps not 'usb start'ed..?
No USB update detected, continuing boot
322 bytes read in 3 ms (104.5 KiB/s)
Importing environment from 0x82000000...
Checking if uenvcmd is set ...
Running default loadzimage ...
6304344 bytes read in 274 ms (21.9 MiB/s)
MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK
Reading overlays list from eMMC
Reading factory fdt name from eMMC
Loading factory fdt imx6ul-wirenboard660
46098 bytes read in 5 ms (8.8 MiB/s)
670 bytes read in 3 ms (217.8 KiB/s)
Applying DT overlay wb6-gsm-sim800
597 bytes read in 3 ms (194.3 KiB/s)
Applying DT overlay wb6-wifi-rtl8723bu
509 bytes read in 3 ms (165 KiB/s)
Applying DT overlay wb6-noradio
334 bytes read in 3 ms (108.4 KiB/s)
Applying DT overlay wb6-eth1
254 bytes read in 4 ms (61.5 KiB/s)
Applying DT overlay temp-industrial
Applying extra overlay
Booting from mmc ...
Kernel image @ 0x82000000 [ 0x000000 - 0x603258 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Device Tree to 9ef77000, end 9ef99fff ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.35-wb142 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Thu Jul 20 07:59:09 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.6.0 (i.MX6UL/ULL)
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x9f000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait ro
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 489364K/524288K available (8192K kernel code, 728K rwdata, 2776K rodata, 1024K init, 283K bss, 18540K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x234/0x3dc with crng_init=0
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000059] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002735] Console: colour dummy device 80x30
[ 0.002799] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.002837] pid_max: default: 32768 minimum: 301
[ 0.003225] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.003260] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004957] CPU: Testing write buffer coherency: ok
[ 0.006176] Setting up static identity map for 0x80100000 - 0x80100078
[ 0.007062] devtmpfs: initialized
[ 0.024559] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.025060] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.025105] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.026471] pinctrl core: initialized pinctrl subsystem
[ 0.028457] NET: Registered protocol family 16
[ 0.030662] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.032598] thermal_sys: Registered thermal governor 'step_wise'
[ 0.032868] cpuidle: using governor menu
[ 0.195539] vdd1p1: supplied by regulator-dummy
[ 0.206581] vdd3p0: supplied by regulator-dummy
[ 0.217666] cpu: supplied by regulator-dummy
[ 0.228714] vddsoc: supplied by regulator-dummy
[ 0.559119] No ATAGs?
[ 0.559181] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.559202] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.559775] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present!
[ 0.560380] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver
[ 0.561894] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000
[ 0.561931] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.604387] mxs-dma 1804000.dma-apbh: initialized
[ 0.609613] SCSI subsystem initialized
[ 0.610111] usbcore: registered new interface driver usbfs
[ 0.610235] usbcore: registered new interface driver hub
[ 0.610345] usbcore: registered new device driver usb
[ 0.611155] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.611280] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.612216] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL)
[ 0.612950] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.613076] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.613747] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL)
[ 0.614452] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.614576] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.615192] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL)
[ 0.616745] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.617097] i2c i2c-1: IMX I2C adapter registered
[ 0.617831] mc: Linux media interface: v0.10
[ 0.617943] videodev: Linux video capture interface: v2.00
[ 0.618076] pps_core: LinuxPPS API ver. 1 registered
[ 0.618097] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.618145] PTP clock support registered
[ 0.618762] Advanced Linux Sound Architecture Driver Initialized.
[ 0.620887] clocksource: Switched to clocksource mxc_timer1
[ 0.638573] NET: Registered protocol family 2
[ 0.639841] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.639940] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.640045] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.640149] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.640339] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.640395] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.640711] NET: Registered protocol family 1
[ 0.641765] RPC: Registered named UNIX socket transport module.
[ 0.641803] RPC: Registered udp transport module.
[ 0.641820] RPC: Registered tcp transport module.
[ 0.641837] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.642908] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.645711] Initialise system trusted keyrings
[ 0.646174] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.657726] NFS: Registering the id_resolver key type
[ 0.657810] Key type id_resolver registered
[ 0.657831] Key type id_legacy registered
[ 0.898644] Key type asymmetric registered
[ 0.898684] Asymmetric key parser 'x509' registered
[ 0.898808] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.898829] io scheduler mq-deadline registered
[ 0.898849] io scheduler kyber registered
[ 0.910627] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[ 0.910676] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 0.914604] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX
[ 1.577634] printk: console [ttymxc0] enabled
[ 1.584117] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 58, base_baud = 5000000) is a IMX
[ 1.594715] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 59, base_baud = 5000000) is a IMX
[ 1.638380] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129)
[ 1.645813] random: fast init done
[ 1.649764] random: crng init done
[ 1.689728] brd: module loaded
[ 1.707874] loop: module loaded
[ 1.711458] at24 5-0050: supply vcc not found, using dummy regulator
[ 1.722906] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.729890] at24 6-0050: supply vcc not found, using dummy regulator
[ 1.741312] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.751265] libphy: Fixed MDIO Bus: probed
[ 1.758240] pps pps0: new PPS source ptp0
[ 1.798504] libphy: fec_enet_mii_bus: probed
[ 1.804005] fec 20b4000.ethernet ethFEC0: registered PHC device 0
[ 1.931591] pps pps1: new PPS source ptp1
[ 1.938239] libphy: fec_enet_mii_bus: probed
[ 1.946949] fec 2188000.ethernet ethFEC1: registered PHC device 1
[ 1.954069] PPP generic driver version 2.4.2
[ 1.958757] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.965398] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.971156] usbcore: registered new interface driver usb-storage
[ 1.977398] usbcore: registered new interface driver usbserial_generic
[ 1.984065] usbserial: USB Serial support registered for generic
[ 2.032979] rtc rtc0: invalid alarm value: 2023-09-01T25:06:00
[ 2.039243] rtc-pcf8563 4-0051: registered as rtc0
[ 2.056018] rtc-pcf8563 4-0051: setting system clock to 2023-09-08T10:15:56 UTC (1694168156)
[ 2.074300] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1
[ 2.080731] i2c /dev entries driver
[ 2.087542] lm75 4-0048: supply vs not found, using dummy regulator
[ 2.099146] lm75 4-0048: hwmon0: sensor 'lm75b'
[ 2.219213] sdhci: Secure Digital Host Controller Interface driver
[ 2.225498] sdhci: Copyright(c) Pierre Ossman
[ 2.229869] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.244659] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.252536] usbcore: registered new interface driver usbhid
[ 2.258137] usbhid: USB HID core driver
[ 2.273454] Initializing XFRM netlink socket
[ 2.277863] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA
[ 2.286193] NET: Registered protocol family 10
[ 2.293963] Segment Routing with IPv6
[ 2.298090] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.306137] NET: Registered protocol family 17
[ 2.311299] Key type dns_resolver registered
[ 2.319604] registered taskstats version 1
[ 2.324384] Loading compiled-in X.509 certificates
[ 2.347058] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[ 2.358992] of_cfs_init
[ 2.361793] of_cfs_init: OK
[ 2.369612] ALSA device list:
[ 2.372652] No soundcards found.
[ 2.376361] Waiting for root device /dev/mmcblk0p3...
[ 2.386289] mmc0: new DDR MMC card at address 0001
[ 2.392058] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[ 2.396984] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
[ 2.403423] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
[ 2.409673] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB, chardev (245:0)
[ 2.420403] mmcblk0: p1 p2 p3 p4 < p5 p6 >
[ 2.448151] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem
[ 2.455552] EXT4-fs (mmcblk0p3): write access will be enabled during recovery
[ 2.776897] EXT4-fs (mmcblk0p3): recovery complete
[ 2.853770] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.862691] VFS: Mounted root (ext4 filesystem) readonly on device 179:3.
[ 2.871200] devtmpfs: mounted
[ 2.877428] Freeing unused kernel memory: 1024K
[ 2.882506] Run /sbin/init as init process
[ 3.314657] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 3.339196] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
[ 3.382267] systemd[1]: Set hostname to <wirenboard-AKQ2UEDD>.
[ 4.988531] systemd[1]: Queued start job for default target Graphical Interface.
[ 5.004227] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 5.049113] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 5.094684] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 5.135320] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ 5.177211] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 5.213523] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 5.252077] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 5.292608] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 5.305648] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 5.342610] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 5.381597] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 5.417082] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 5.452177] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 5.516730] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 5.527409] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 5.565043] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 5.612820] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 5.652919] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 5.695772] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 5.713569] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 5.762917] systemd[1]: Mounting /sys/kernel/config...
Mounting /sys/kernel/config...
[ 5.817258] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 5.862133] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 5.884020] systemd[1]: Starting Create list of static device nodes for the current kernel...
Starting Create list of st…odes for the current kernel...
[ 5.942868] systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
[ 5.981759] systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
[ 6.003566] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 6.026472] fuse: init (API version 7.32)
[ 6.035500] systemd[1]: Starting File System Check on Root Device...
Starting File System Check on Root Device...
[ 6.109525] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 6.152196] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 6.215704] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 6.338724] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 6.372473] systemd[1]: Mounted /sys/kernel/config.
[ OK ] Mounted /sys/kernel/config.
[ 6.402870] systemd[1]: Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Debug File System.
[ 6.431286] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ OK ] Finished Create list of st… nodes for the current kernel.
[ 6.483480] systemd[1]: modprobe@drm.service: Succeeded.
[ 6.511617] systemd[1]: Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module drm.
[ 6.553686] systemd[1]: modprobe@fuse.service: Succeeded.
[ 6.581478] systemd[1]: Finished Load Kernel Module fuse.
[ OK ] Finished Load Kernel Module fuse.
[ 6.604240] systemd[1]: Finished File System Check on Root Device.
[ OK ] Finished File System Check on Root Device.
[ 6.644259] systemd[1]: Finished Load Kernel Modules.
[ OK ] Finished Load Kernel Modules.
[ 6.683776] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 6.718582] systemd[1]: Started File System Check Daemon to report status.
[ OK ] Started File System Check Daemon to report status.
[ 6.792385] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 6.854443] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 6.925871] systemd[1]: Mounted FUSE Control File System.
[ OK ] Mounted FUSE Control File System.
[ 7.002134] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ 7.097994] EXT4-fs (mmcblk0p3): re-mounted. Opts: discard,errors=remount-ro
[ OK ] Finished Apply Kernel Variables.
[ OK ] Finished Remount Root and Kernel File Systems.
Starting Load/Save Random Seed...
Starting Create System Users...
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Coldplug All udev Devices.
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Finished Create System Users.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Set up automount mnt-sdcard.automount.
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Started Rule-based Manager for Device Events and Files.
[ 10.013341] Driver for 1-wire Dallas network protocol.
[ 10.052235] gpio-11 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 10.161790] gpio-108 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 10.560474] fec 20b4000.ethernet eth1: renamed from ethFEC0
[ OK ] Found device /dev/ttymxc0.
[ 11.699684] fec 2188000.ethernet eth0: renamed from ethFEC1
[ 11.756134] imx_usb 2184000.usb: No over current polarity defined
[ 11.827563] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 11.911071] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 11.998740] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 12.054795] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 12.063151] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.070383] usb usb1: Product: EHCI Host Controller
[ 12.075309] usb usb1: Manufacturer: Linux 5.10.35-wb142 ehci_hcd
[ 12.081350] usb usb1: SerialNumber: ci_hdrc.0
[ 12.291537] hub 1-0:1.0: USB hub found
[ 12.328524] hub 1-0:1.0: 1 port detected
[ 12.449448] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 12.484948] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ 12.601134] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 12.655423] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 12.663789] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.671051] usb usb2: Product: EHCI Host Controller
[ 12.675937] usb usb2: Manufacturer: Linux 5.10.35-wb142 ehci_hcd
[ 12.681975] usb usb2: SerialNumber: ci_hdrc.1
[ 12.711123] usb usb1-port1: over-current condition
[ 12.930122] hub 2-0:1.0: USB hub found
[ 12.981084] hub 2-0:1.0: 1 port detected
[ 13.401027] usb 2-1: new high-speed USB device number 2 using ci_hdrc
[ 13.651630] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 13.659861] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 13.807358] hub 2-1:1.0: USB hub found
[ 13.823879] hub 2-1:1.0: 4 ports detected
[ 14.201043] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc
[ 14.392847] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00
[ 14.401311] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 14.408652] usb 2-1.1: Product: 802.11n WLAN Adapter
[ 14.413668] usb 2-1.1: Manufacturer: Realtek
[ 14.417946] usb 2-1.1: SerialNumber: 00e04c000001
[ 14.491909] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 15.091109] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ OK ] Found device [ 15.125587] Bluetooth: Core ver 2.22
/dev/mmcblk0p5.
[ 15.136529] NET: Registered protocol family 31
[ 15.141080] Bluetooth: HCI device and connection manager initialized
[ 15.159901] Bluetooth: HCI socket layer initialized
[ 15.180067] Bluetooth: L2CAP socket layer initialized
[ 15.196407] Bluetooth: SCO socket layer initialized
[ 15.282631] usbcore: registered new interface driver btusb
[ 15.296206] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
[ 15.305051] usb 1-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 2.00
[ 15.313308] usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[ 15.320458] usb 1-1: Product: DataTraveler 3.0
[ 15.324943] usb 1-1: Manufacturer: Kingston
[ 15.329133] usb 1-1: SerialNumber: E0D55EA573DE1750C92F0830
[ 15.340206] Bluetooth: hci0: RTL: rom_version status=0 version=1
[ 15.346326] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin
[ 15.356184] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin
[ 15.362776] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2
[ 15.372081] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496
[ 15.389745] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 15.497758] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 15.537513] scsi host0: usb-storage 1-1:1.0
[ OK ] Found device /dev/mmcblk0p6.
[ 15.558048] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[ 16.027961] RTL871X: module init start
[ 16.031823] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40
[ 16.197072] Bluetooth: hci0: RTL: fw version 0x0e2f9f73
[ OK ] Found device /sys/subsystem/net/devices/eth1.
[ 16.229822] RTL871X: rtw_ndev_init(wlan0)
[ 16.240414] RTL871X: rtw_ndev_init(wlan1)
[ 16.259715] usbcore: registered new interface driver rtl8723bu
[ 16.265759] RTL871X: module init ret=0
[ 16.401648] usbcore: registered new interface driver rtl8xxxu
[ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
Activating swap /dev/mmcblk0p5...
Starting File System Check on /dev/mmcblk0p6...
[ 16.579409] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 3.0 0000 PQ: 0 ANSI: 4
Starting Load/Save RF Kill Switch Status...
[ 16.660496] sd 0:0:0:0: [sda] 60538881 512-byte logical blocks: (31.0 GB/28.9 GiB)
[ 16.727510] sd 0:0:0:0: [sda] Write Protect is off
[ 16.779234] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 16.884720] sda: sda1
[ 16.933000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 17.437523] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SSDsc
[ OK ] Activated swap /dev/mmcblk0p5.
[ OK ] Started Load/Save RF Kill Switch Status.
[ OK ] Finished Helper to synchronize boot up for ifupdown.
[ OK ] Reached target Swap.
[ OK ] Finished File System Check on /dev/mmcblk0p6.
Mounting /mnt/data...
[ 18.481853] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: discard
[ OK ] Mounted /mnt/data.
Mounting /var/log...
[ OK ] Mounted /var/log.
[ OK ] Reached target Local File Systems.
[ OK ] Started ifup for eth0.
[ OK ] Started ifup for eth1.
Starting Flush Journal to Persistent Storage...
Starting prepare mounts and symlinks to config files...
[ 18.990750] systemd-journald[122]: Received client request to flush runtime journal.
[ 19.072488] systemd-journald[122]: File /var/log/journal/c6e020b323ad4d2ebb8a1415d9658cbf/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Finished prepare mounts and symlinks to config files.
Starting Create Volatile Files and Directories...
[ OK ] Finished Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Monitor directorie… templates for wb-mqtt-serial.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Paths.
[ OK ] Reached target Timers.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Listening on fcgiwrap Socket.
[ OK ] Listening on KNX Daemon (socket).
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Bluetooth service...
[ OK ] Started Regular background program processing daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Network Manager...
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting Authorization Manager...
Starting User Login Management...
[ OK ] Started watch config files.
Starting Initialize Wiren Board Device Tree overlays...
[ OK ] Started Generates wb-mqtt-… UI schema for wb-mqtt-confed.
Starting Avahi mDNS/DNS-SD Stack...
[ 23.659286] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 23.664754] Bluetooth: BNEP filters: protocol multicast
[ 23.761027] Bluetooth: BNEP socket layer initialized
Starting WPA supplicant...