забыл приложить логи загрузки без флешки:
U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38)
DRAM init ok, rows:16, ncs:1, size: 1024MB
.p0_mpdgctrl0 = 0x0113010d
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3c40
.p0_mpwrdlctl = 0x3f3f3734
.p0_mpwldectrl0 = 0x000d000d
.p0_mpwldectrl1 = 0x000e000e
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 39C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 1 GiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 1
U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38)
DRAM init ok, rows:16, ncs:1, size: 1024MB
.p0_mpdgctrl0 = 0x0113010d
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3c3f
.p0_mpwrdlctl = 0x3f3f3834
.p0_mpwldectrl0 = 0x000d000d
.p0_mpwldectrl1 = 0x000e000e
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 41C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 1 GiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
USB0: USB EHCI 1.00
USB1: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
No storage devices, perhaps not 'usb start'ed..?
No USB update detected, continuing boot
switch to partitions #0, OK
mmc0(part 0) is current device
SD/MMC found on device 0
324 bytes read in 61 ms (4.9 KiB/s)
Importing environment from 0x82000000...
Checking if uenvcmd is set ...
Running default loadzimage ...
5899184 bytes read in 383 ms (14.7 MiB/s)
MMC read: dev # 0, block # 2016, count 32 ... 32 blocks read: OK
Reading overlays list from eMMC
Reading factory fdt name from eMMC
Loading factory fdt imx6ul-wirenboard690
47104 bytes read in 99 ms (463.9 KiB/s)
485 bytes read in 142 ms (2.9 KiB/s)
Applying DT overlay wb6-nogsm
597 bytes read in 136 ms (3.9 KiB/s)
Applying DT overlay wb6-wifi-rtl8723bu
509 bytes read in 164 ms (2.9 KiB/s)
Applying DT overlay wb6-noradio
334 bytes read in 104 ms (2.9 KiB/s)
Applying DT overlay wb6-eth1
254 bytes read in 117 ms (2 KiB/s)
Applying DT overlay temp-industrial
Applying extra overlay
Booting from mmc ...
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Device Tree to bef4c000, end bef6efff ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.35-wb116 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 6.3.0-18) 6.3.0 20170516, GNU ld (GNU Binutils for Debian) 2.28) #1 Wed Jul 6 16:10:09 UTC 2022
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.9.0 (i.MX6UL/ULL)
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0xbf000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 259840
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait ro
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1008680K/1048576K available (8192K kernel code, 714K rwdata, 2680K rodata, 1024K init, 272K bss, 23512K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x238/0x3d4 with crng_init=0
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000066] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002848] Console: colour dummy device 80x30
[ 0.002916] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.002960] pid_max: default: 32768 minimum: 301
[ 0.003411] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.003456] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.005078] CPU: Testing write buffer coherency: ok
[ 0.006189] Setting up static identity map for 0x80100000 - 0x80100078
[ 0.007213] devtmpfs: initialized
[ 0.025644] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.026187] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.026236] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.027639] pinctrl core: initialized pinctrl subsystem
[ 0.029730] NET: Registered protocol family 16
[ 0.032089] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.034185] thermal_sys: Registered thermal governor 'step_wise'
[ 0.034477] cpuidle: using governor menu
[ 0.234788] vdd1p1: supplied by regulator-dummy
[ 0.247713] vdd3p0: supplied by regulator-dummy
[ 0.260599] cpu: supplied by regulator-dummy
[ 0.273496] vddsoc: supplied by regulator-dummy
[ 0.637960] No ATAGs?
[ 0.638025] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.638051] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.638666] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present!
[ 0.639342] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver
[ 0.640768] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000
[ 0.640807] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.682182] mxs-dma 1804000.dma-apbh: initialized
[ 0.687646] SCSI subsystem initialized
[ 0.688185] usbcore: registered new interface driver usbfs
[ 0.688316] usbcore: registered new interface driver hub
[ 0.688434] usbcore: registered new device driver usb
[ 0.689275] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.689427] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.690778] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL)
[ 0.691707] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.691842] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.692468] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL)
[ 0.693168] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.693298] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.694002] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL)
[ 0.695607] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.695976] i2c i2c-1: IMX I2C adapter registered
[ 0.696729] mc: Linux media interface: v0.10
[ 0.696845] videodev: Linux video capture interface: v2.00
[ 0.697008] pps_core: LinuxPPS API ver. 1 registered
[ 0.697033] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.697094] PTP clock support registered
[ 0.697742] Advanced Linux Sound Architecture Driver Initialized.
[ 0.699915] clocksource: Switched to clocksource mxc_timer1
[ 0.718122] NET: Registered protocol family 2
[ 0.719300] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.719415] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.719618] TCP bind hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.719811] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.720183] UDP hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.720263] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.720647] NET: Registered protocol family 1
[ 0.721607] RPC: Registered named UNIX socket transport module.
[ 0.721642] RPC: Registered udp transport module.
[ 0.721662] RPC: Registered tcp transport module.
[ 0.721679] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.722871] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.725797] Initialise system trusted keyrings
[ 0.726249] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.738172] NFS: Registering the id_resolver key type
[ 0.738253] Key type id_resolver registered
[ 0.738274] Key type id_legacy registered
[ 0.739189] Key type asymmetric registered
[ 0.739228] Asymmetric key parser 'x509' registered
[ 0.739332] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.739360] io scheduler mq-deadline registered
[ 0.739382] io scheduler kyber registered
[ 0.751774] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[ 0.751825] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 0.755844] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX
[ 1.418995] printk: console [ttymxc0] enabled
[ 1.425538] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX
[ 1.469443] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129)
[ 1.476877] random: fast init done
[ 1.480860] random: crng init done
[ 1.520848] brd: module loaded
[ 1.538805] loop: module loaded
[ 1.542423] at24 5-0050: supply vcc not found, using dummy regulator
[ 1.553899] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.560914] at24 6-0050: supply vcc not found, using dummy regulator
[ 1.572356] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.584891] libphy: Fixed MDIO Bus: probed
[ 1.710595] pps pps0: new PPS source ptp0
[ 1.717073] libphy: fec_enet_mii_bus: probed
[ 1.725980] fec 20b4000.ethernet ethFEC0: registered PHC device 0
[ 1.850613] pps pps1: new PPS source ptp1
[ 1.891769] libphy: fec_enet_mii_bus: probed
[ 1.897063] fec 2188000.ethernet ethFEC1: registered PHC device 1
[ 1.904193] PPP generic driver version 2.4.2
[ 1.908920] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.915571] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.921340] usbcore: registered new interface driver usb-storage
[ 1.927595] usbcore: registered new interface driver usbserial_generic
[ 1.934280] usbserial: USB Serial support registered for generic
[ 1.983672] rtc rtc0: invalid alarm value: 2023-04-04T40:04:00
[ 1.990028] rtc-pcf8563 4-0051: registered as rtc0
[ 2.006844] rtc-pcf8563 4-0051: setting system clock to 2023-04-24T12:06:03 UTC (1682337963)
[ 2.025592] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1
[ 2.032131] i2c /dev entries driver
[ 2.038978] lm75 4-0048: supply vs not found, using dummy regulator
[ 2.050659] lm75 4-0048: hwmon0: sensor 'lm75b'
[ 2.171153] sdhci: Secure Digital Host Controller Interface driver
[ 2.177364] sdhci: Copyright(c) Pierre Ossman
[ 2.181808] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.196047] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.203924] usbcore: registered new interface driver usbhid
[ 2.209523] usbhid: USB HID core driver
[ 2.226109] NET: Registered protocol family 10
[ 2.230747] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA
[ 2.241208] Segment Routing with IPv6
[ 2.245315] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.253286] NET: Registered protocol family 17
[ 2.258081] Key type dns_resolver registered
[ 2.266905] registered taskstats version 1
[ 2.271147] Loading compiled-in X.509 certificates
[ 2.293054] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[ 2.304996] of_cfs_init
[ 2.307684] of_cfs_init: OK
[ 2.315533] ALSA device list:
[ 2.318523] No soundcards found.
[ 2.322332] Waiting for root device /dev/mmcblk0p2...
[ 2.370163] mmc0: new DDR MMC card at address 0001
[ 2.377473] mmcblk0: mmc0:0001 008GB0 7.28 GiB
[ 2.383314] mmcblk0boot0: mmc0:0001 008GB0 partition 1 8.00 MiB
[ 2.390381] mmcblk0boot1: mmc0:0001 008GB0 partition 2 8.00 MiB
[ 2.397045] mmcblk0rpmb: mmc0:0001 008GB0 partition 3 4.00 MiB, chardev (245:0)
[ 2.409724] mmcblk0: p1 p2 p3 p4 < p5 p6 >
[ 2.448477] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.457049] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.469397] devtmpfs: mounted
[ 2.477818] Freeing unused kernel memory: 1024K
[ 2.483361] Run /sbin/init as init process
[ 2.817106] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 2.835963] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 9 (stretch)!
[ 2.881630] systemd[1]: Set hostname to <wirenboard-A5ZXZ7OF>.
[ 3.376923] systemd[1]: [/lib/systemd/system/wb-mqtt-w1.service:10] Unknown lvalue 'StartLimitIntervalSec' in section 'Service'
[ 3.539512] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 3.570573] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 3.612257] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 3.653036] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 3.694090] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 3.745866] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
Mounting POSIX Message Queue File System...
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ OK ] Listening on fsck to fsckd communication Socket.
[ OK ] Listening on Syslog Socket.
[ OK ] Listening on Journal Socket.
[ OK ] Reached target Remote File Systems.
Mounting /sys/kernel/config...
[ OK ] Listening on udev Kernel Socket.
[ OK ] Listening on udev Control Socket.
Starting Load Kernel Modules...
Starting File System Check on Root Device...
[ OK ] Reached target Slices.
[ OK ] Created slice system-getty.slice.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Reached target Encrypted Volumes.
[ OK ] Listening on Journal Socket (/dev/log).
Starting Journal Service...
Starting Create list of required st…ce nodes for the current kernel...
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Debug File System.
[ OK ] Mounted /sys/kernel/config.
[ OK ] Started Load Kernel Modules.
[ OK ] Started File System Check on Root Device.
[ OK ] Started Create list of required sta…vice nodes for the current kernel.
[ OK ] Started Journal Service.
[ OK ] Started File System Check Daemon to report status.
Starting Create Static Device Nodes in /dev...
Starting Remount Root and Kernel File Systems...
Starting Apply Kernel Variables...
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ 4.901758] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Remount Root and Kernel File Systems.
Starting Load/Save Random Seed...
Starting prepare partitions at first boot...
Starting udev Coldplug all Devices...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started prepare partitions at first boot.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Started udev Coldplug all Devices.
[ 7.058700] Driver for 1-wire Dallas network protocol.
[ 7.107510] gpio-68 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 7.191320] gpio-11 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ OK ] Found device /dev/ttymxc0.
[ 7.430979] fec 20b4000.ethernet eth1: renamed from ethFEC0
[ 7.898978] imx_usb 2184000.usb: No over current polarity defined
[ 8.043958] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 8.048913] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 8.118505] fec 2188000.ethernet eth0: renamed from ethFEC1
[ 8.190216] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 8.251721] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 8.260076] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.267307] usb usb1: Product: EHCI Host Controller
[ 8.272234] usb usb1: Manufacturer: Linux 5.10.35-wb116 ehci_hcd
[ 8.278266] usb usb1: SerialNumber: ci_hdrc.0
[ 8.652570] hub 1-0:1.0: USB hub found
[ 8.685150] hub 1-0:1.0: 1 port detected
[ OK ] Found device /dev/mmcblk0p5.
Activating swap /dev/mmcblk0p5...
[ 8.803316] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SS
[ 8.860191] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 8.865145] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ OK ] Activated swap /dev/mmcblk0p5.
[ OK ] Reached target Swap.
[ OK ] Found device /dev/mmcblk0p6.
Starting File System Check on /dev/mmcblk0p6...
[ 9.110198] usb usb1-port1: over-current condition
[ 9.115074] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 9.204804] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 9.213183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.220447] usb usb2: Product: EHCI Host Controller
[ 9.225333] usb usb2: Manufacturer: Linux 5.10.35-wb116 ehci_hcd
[ 9.231367] usb usb2: SerialNumber: ci_hdrc.1
[ OK ] Started File System Check on /dev/mmcblk0p6.
Mounting /mnt/data...
[ 9.547843] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[ OK ] Mounted /mnt/data.
Mounting /var/log...
[ OK ] Mounted /var/log.
Starting Flush Journal to Persistent Storage...
[ 9.784575] systemd-journald[107]: Received request to flush runtime journal from PID 1
[ 9.824662] systemd-journald[107]: File /var/log/journal/84ebb9a9047d51bdaa4e7ff362c682db/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 9.893256] hub 2-0:1.0: USB hub found
[ 9.960138] hub 2-0:1.0: 1 port detected
[ OK ] Started Flush Journal to Persistent Storage.
[ 10.390037] usb 2-1: new high-speed USB device number 2 using ci_hdrc
[ 10.600687] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 10.608915] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 10.631046] hub 2-1:1.0: USB hub found
[ OK ] Found device [ 10.641150] hub 2-1:1.0: 4 ports detected
/sys/subsystem/net/devices/eth1.
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ 10.970047] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc
[ 11.122499] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00
[ 11.131037] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 11.138466] usb 2-1.1: Product: 802.11n WLAN Adapter
[ 11.143569] usb 2-1.1: Manufacturer: Realtek
[ 11.147882] usb 2-1.1: SerialNumber: 00e04c000001
[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ 11.372970] Bluetooth: Core ver 2.22
[ 11.376741] NET: Registered protocol family 31
[ 11.381279] Bluetooth: HCI device and connection manager initialized
[ 11.405978] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 11.414947] Bluetooth: HCI socket layer initialized
[ 11.419860] Bluetooth: L2CAP socket layer initialized
[ 11.427372] Bluetooth: SCO socket layer initialized
[ 11.530278] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 11.538545] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 11.554574] cfg80211: failed to load regulatory.db
Starting Load/Save RF Ki[ 11.578305] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
ll Switch Status...
[ 11.589292] Bluetooth: hci0: RTL: rom_version status=0 version=1
[ 11.595521] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin
[ 11.608152] usbcore: registered new interface driver btusb
[ 11.616441] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin
[ 11.623140] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2
[ 11.632402] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496
[ OK ] Started Load/Save RF Kill Switch Status.
[ 12.375617] RTL871X: module init start
[ 12.379403] RTL871X: rtl8723bu v4.3.6.11_12942.20141204_BTCOEX20140507-4E40
[ 12.386476] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40
[ 12.455094] Bluetooth: hci0: RTL: fw version 0x0e2f9f73
[ 12.573367] RTL871X: rtw_ndev_init(wlan0)
[ 12.583384] RTL871X: rtw_ndev_init(wlan1)
[ 12.597784] usbcore: registered new interface driver rtl8723bu
[ 12.603718] RTL871X: module init ret=0
[ 12.711534] usbcore: registered new interface driver rtl8xxxu
[ OK ] Found device 802.11n_WLAN_Adapter.
[ TIME ] Timed out waiting for device dev-di…3f\x2db877\x2dfe2054f6bec9.device.
[DEPEND] Dependency failed for /mnt/ext_flash.
[DEPEND] Dependency failed for Local File Systems.
[ OK ] Started ifup for eth1.
[ OK ] Started ifup for eth0.
[ OK ] Started ifup for wlan0.
[ OK ] Reached target Bluetooth.
[ OK ] Reached target Timers.
[ OK ] Closed Syslog Socket.
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Reached target Sockets.
[ OK ] Reached target Paths.
Starting prepare mounts and symlinks to config files...
[ OK ] Started Emergency Shell.
[ OK ] Reached target Emergency Mode.
[ OK ] Reached target Login Prompts.
[ 95.321902] RTL871X: RTW_ADAPTIVITY_EN_
[ 95.321928] AUTO, chplan:0x20, Regulation:3,3
[ 95.330216] RTL871X: RTW_ADAPTIVITY_MODE_
[ 95.330221] NORMAL
[ OK ] Started prepare mounts and symlinks to config files.
Starting Create Volatile Files and Directories...
Starting Raise network interfaces...
[ OK ] Started Raise network interfaces.
[ OK ] Reached target Network.
[ OK ] Reached target Network is Online.
[ OK ] Started Create Volatile Files and Directories.
[ OK ] Reached target System Time Synchronized.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Update UTMP about System Boot/Shutdown.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Update UTMP about System Runlevel Changes.
You are in emergency mode. After logging in, type "journalctl -xb" to view
system logs, "systemctl reboot" to reboot, "systemctl default" or ^D to
try agaiGive root password for maintenance
(or press Control-D to continue): [ 98.731276] RTL871X: nolinked power save enter
[ 101.310269] SMSC LAN8710/LAN8720 20b4000.ethernet-1:01: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL)
[ 103.450408] fec 20b4000.ethernet eth1: Link is Up - 100Mbps/Full - flow control off
[ 103.458124] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 105.120156] SMSC LAN8710/LAN8720 20b4000.ethernet-1:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet-1:00, irq=POLL)
