Блок питания HDR-100-24N через WB-UPS v.2 (правда у него батарея не держит, я так понял). Резервного нет. Фактически 24,12 В
Пришлите полный вывод при обновлении через флешку. По одной строке не понятно.
U-Boot SPL 2021.10-wb1.4.3-ge44f7a4224 (Oct 13 2022 - 09:52:21 +0000)
DRAM init ok, rows:15, ncs:1, size: 512MB
.p0_mpdgctrl0 = 0x0112010f
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3d3d
.p0_mpwrdlctl = 0x3f3f3836
.p0_mpwldectrl0 = 0x00080009
.p0_mpwldectrl1 = 0x000a000a
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2021.10-wb1.4.3-ge44f7a4224 (Oct 13 2022 - 09:52:21 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 64C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 512 MiB
MMC: FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Loading Environment from MMC... OK
Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd otp_program otp_aes_program
## Info: input data size = 43 = 0x2B
bootcount=0
mmcpart=3
upgrade_available=0
Environment size: 43/8188 bytes
## Resetting to default environment
## Info: input data size = 43 = 0x2B
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
Bus usb@2184000: USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 2 USB Device(s) found
scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80
USB device not accepting new address (error=22)
1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Device 0: Vendor: General Rev: 5.00 Prod: UDisk
Type: Removable Hard Disk
Capacity: 7680.0 MB = 7.5 GB (15728640 x 512)
** No partition table - usb 0 **
Couldn't find partition usb 0:1
Can't set block device
** No partition table - usb 0 **
Couldn't find partition usb 0:1
Can't set block device
No USB update detected, continuing boot
switch to partitions #0, OK
mmc1(part 0) is current device
SD/MMC found on device 1
322 bytes read in 3 ms (104.5 KiB/s)
Importing environment from 0x82000000...
Checking if uenvcmd is set ...
Running default loadzimage ...
6304344 bytes read in 274 ms (21.9 MiB/s)
MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK
Reading overlays list from eMMC
Reading factory fdt name from eMMC
Loading factory fdt imx6ul-wirenboard660
46098 bytes read in 5 ms (8.8 MiB/s)
670 bytes read in 3 ms (217.8 KiB/s)
Applying DT overlay wb6-gsm-sim800
597 bytes read in 3 ms (194.3 KiB/s)
Applying DT overlay wb6-wifi-rtl8723bu
509 bytes read in 4 ms (124 KiB/s)
Applying DT overlay wb6-noradio
334 bytes read in 3 ms (108.4 KiB/s)
Applying DT overlay wb6-eth1
254 bytes read in 4 ms (61.5 KiB/s)
Applying DT overlay temp-industrial
Applying extra overlay
Booting from mmc ...
Kernel image @ 0x82000000 [ 0x000000 - 0x603258 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Device Tree to 9ef78000, end 9ef9afff ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.35-wb142 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Thu Jul 20 07:59:09 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.6.0 (i.MX6UL/ULL)
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x9f000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait ro
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 489364K/524288K available (8192K kernel code, 728K rwdata, 2776K rodata, 1024K init, 283K bss, 18540K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x234/0x3dc with crng_init=0
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000058] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002736] Console: colour dummy device 80x30
[ 0.002801] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.002840] pid_max: default: 32768 minimum: 301
[ 0.003227] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.003262] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004945] CPU: Testing write buffer coherency: ok
[ 0.006173] Setting up static identity map for 0x80100000 - 0x80100078
[ 0.007037] devtmpfs: initialized
[ 0.024454] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.024959] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.025007] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.026371] pinctrl core: initialized pinctrl subsystem
[ 0.028375] NET: Registered protocol family 16
[ 0.030583] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.032533] thermal_sys: Registered thermal governor 'step_wise'
[ 0.032806] cpuidle: using governor menu
[ 0.195145] vdd1p1: supplied by regulator-dummy
[ 0.206173] vdd3p0: supplied by regulator-dummy
[ 0.217213] cpu: supplied by regulator-dummy
[ 0.228212] vddsoc: supplied by regulator-dummy
[ 0.557811] No ATAGs?
[ 0.557870] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.557890] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.558465] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present!
[ 0.559077] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver
[ 0.560594] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000
[ 0.560633] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.602904] mxs-dma 1804000.dma-apbh: initialized
[ 0.608254] SCSI subsystem initialized
[ 0.608746] usbcore: registered new interface driver usbfs
[ 0.608869] usbcore: registered new interface driver hub
[ 0.608980] usbcore: registered new device driver usb
[ 0.609789] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.609913] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.610845] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL)
[ 0.611577] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.611704] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.612291] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL)
[ 0.612982] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.613104] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.613795] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL)
[ 0.615353] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.615700] i2c i2c-1: IMX I2C adapter registered
[ 0.616440] mc: Linux media interface: v0.10
[ 0.616554] videodev: Linux video capture interface: v2.00
[ 0.616685] pps_core: LinuxPPS API ver. 1 registered
[ 0.616707] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.616755] PTP clock support registered
[ 0.617373] Advanced Linux Sound Architecture Driver Initialized.
[ 0.619487] clocksource: Switched to clocksource mxc_timer1
[ 0.637232] NET: Registered protocol family 2
[ 0.638484] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.638581] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.638687] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.638791] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.638982] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.639038] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.639363] NET: Registered protocol family 1
[ 0.640415] RPC: Registered named UNIX socket transport module.
[ 0.640451] RPC: Registered udp transport module.
[ 0.640469] RPC: Registered tcp transport module.
[ 0.640487] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.641564] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.644368] Initialise system trusted keyrings
[ 0.644854] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.656397] NFS: Registering the id_resolver key type
[ 0.656473] Key type id_resolver registered
[ 0.656492] Key type id_legacy registered
[ 0.890817] Key type asymmetric registered
[ 0.890857] Asymmetric key parser 'x509' registered
[ 0.890979] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.891002] io scheduler mq-deadline registered
[ 0.891021] io scheduler kyber registered
[ 0.902852] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[ 0.902902] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 0.906738] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX
[ 1.569783] printk: console [ttymxc0] enabled
[ 1.576203] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 58, base_baud = 5000000) is a IMX
[ 1.586845] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 59, base_baud = 5000000) is a IMX
[ 1.630437] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129)
[ 1.639794] random: fast init done
[ 1.643765] random: crng init done
[ 1.682007] brd: module loaded
[ 1.700163] loop: module loaded
[ 1.703653] at24 5-0050: supply vcc not found, using dummy regulator
[ 1.715086] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.722133] at24 6-0050: supply vcc not found, using dummy regulator
[ 1.733477] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.743412] libphy: Fixed MDIO Bus: probed
[ 1.750462] pps pps0: new PPS source ptp0
[ 1.790908] libphy: fec_enet_mii_bus: probed
[ 1.796198] fec 20b4000.ethernet ethFEC0: registered PHC device 0
[ 1.920173] pps pps1: new PPS source ptp1
[ 1.926837] libphy: fec_enet_mii_bus: probed
[ 1.935522] fec 2188000.ethernet ethFEC1: registered PHC device 1
[ 1.942630] PPP generic driver version 2.4.2
[ 1.947313] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.953954] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.959723] usbcore: registered new interface driver usb-storage
[ 1.965975] usbcore: registered new interface driver usbserial_generic
[ 1.972639] usbserial: USB Serial support registered for generic
[ 2.021556] rtc rtc0: invalid alarm value: 2023-09-01T25:06:00
[ 2.027819] rtc-pcf8563 4-0051: registered as rtc0
[ 2.044576] rtc-pcf8563 4-0051: setting system clock to 2023-09-07T11:36:38 UTC (1694086598)
[ 2.062859] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1
[ 2.069295] i2c /dev entries driver
[ 2.076116] lm75 4-0048: supply vs not found, using dummy regulator
[ 2.087714] lm75 4-0048: hwmon0: sensor 'lm75b'
[ 2.207759] sdhci: Secure Digital Host Controller Interface driver
[ 2.214039] sdhci: Copyright(c) Pierre Ossman
[ 2.218410] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.233237] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.241133] usbcore: registered new interface driver usbhid
[ 2.246732] usbhid: USB HID core driver
[ 2.262060] Initializing XFRM netlink socket
[ 2.266463] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA
[ 2.274787] NET: Registered protocol family 10
[ 2.282577] Segment Routing with IPv6
[ 2.286698] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.294731] NET: Registered protocol family 17
[ 2.299889] Key type dns_resolver registered
[ 2.308195] registered taskstats version 1
[ 2.312971] Loading compiled-in X.509 certificates
[ 2.335684] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[ 2.347611] of_cfs_init
[ 2.350416] of_cfs_init: OK
[ 2.358229] ALSA device list:
[ 2.361268] No soundcards found.
[ 2.364978] Waiting for root device /dev/mmcblk0p3...
[ 2.374831] mmc0: new DDR MMC card at address 0001
[ 2.380606] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[ 2.385534] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
[ 2.391979] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
[ 2.398223] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB, chardev (245:0)
[ 2.408941] mmcblk0: p1 p2 p3 p4 < p5 p6 >
[ 2.436600] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem
[ 2.444001] EXT4-fs (mmcblk0p3): write access will be enabled during recovery
[ 2.883076] EXT4-fs (mmcblk0p3): recovery complete
[ 2.890840] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.899077] VFS: Mounted root (ext4 filesystem) readonly on device 179:3.
[ 2.907245] devtmpfs: mounted
[ 2.917172] Freeing unused kernel memory: 1024K
[ 2.922664] Run /sbin/init as init process
[ 3.351514] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 3.375977] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
[ 3.420860] systemd[1]: Set hostname to <wirenboard-AKQ2UEDD>.
[ 5.021872] systemd[1]: Queued start job for default target Graphical Interface.
[ 5.037464] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 5.073106] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 5.113321] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 5.157095] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ 5.205644] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 5.242083] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 5.280593] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 5.322445] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 5.336756] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 5.380792] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 5.420144] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 5.455480] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 5.492430] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 5.561041] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 5.571955] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 5.612049] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 5.661810] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 5.701419] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 5.744844] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 5.771635] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 5.822735] systemd[1]: Mounting /sys/kernel/config...
Mounting /sys/kernel/config...
[ 5.875986] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 5.920644] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 5.942375] systemd[1]: Starting Create list of static device nodes for the current kernel...
Starting Create list of st…odes for the current kernel...
[ 6.001387] systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
[ 6.040561] systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
[ 6.070009] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 6.093556] fuse: init (API version 7.32)
[ 6.099135] systemd[1]: Starting File System Check on Root Device...
Starting File System Check on Root Device...
[ 6.170801] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 6.240730] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 6.297382] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 6.395435] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 6.467438] systemd[1]: Mounted /sys/kernel/config.
[ OK ] Mounted /sys/kernel/config.
[ 6.511624] systemd[1]: Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Debug File System.
[ 6.541550] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ OK ] Finished Create list of st… nodes for the current kernel.
[ 6.644765] systemd[1]: modprobe@drm.service: Succeeded.
[ 6.671954] systemd[1]: Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module drm.
[ 6.701393] systemd[1]: modprobe@fuse.service: Succeeded.
[ 6.720015] systemd[1]: Finished Load Kernel Module fuse.
[ OK ] Finished Load Kernel Module fuse.
[ 6.741938] systemd[1]: Finished File System Check on Root Device.
[ OK ] Finished File System Check on Root Device.
[ 6.770643] systemd[1]: Finished Load Kernel Modules.
[ OK ] Finished Load Kernel Modules.
[ 6.823093] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 6.874745] systemd[1]: Started File System Check Daemon to report status.
[ OK ] Started File System Check Daemon to report status.
[ 6.962994] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 7.056120] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 7.104518] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Mounted FUSE Control File System.
[ 7.204364] EXT4-fs (mmcblk0p3): re-mounted. Opts: discard,errors=remount-ro
[ OK ] Finished Remount Root and Kernel File Systems.
[ OK ] Finished Apply Kernel Variables.
Starting Load/Save Random Seed...
Starting Create System Users...
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Create System Users.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Coldplug All udev Devices.
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Set up automount mnt-sdcard.automount.
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Started Rule-based Manager for Device Events and Files.
[ 9.988336] Driver for 1-wire Dallas network protocol.
[ 10.083254] gpio-11 (onewire_w1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 10.150148] gpio-108 (onewire_w2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ OK ] Found device /dev/ttymxc0.
[ 10.862059] fec 20b4000.ethernet eth1: renamed from ethFEC0
[ 11.695314] fec 2188000.ethernet eth0: renamed from ethFEC1
[ 11.713981] imx_usb 2184000.usb: No over current polarity defined
[ 11.773150] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 11.778101] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 11.939617] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 11.968187] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 11.976557] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.983819] usb usb1: Product: EHCI Host Controller
[ 11.988705] usb usb1: Manufacturer: Linux 5.10.35-wb142 ehci_hcd
[ 11.994737] usb usb1: SerialNumber: ci_hdrc.0
[ 12.176825] hub 1-0:1.0: USB hub found
[ 12.225868] hub 1-0:1.0: 1 port detected
[ 12.308484] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 12.381587] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ 12.475540] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 12.529856] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 12.538148] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.545437] usb usb2: Product: EHCI Host Controller
[ 12.550347] usb usb2: Manufacturer: Linux 5.10.35-wb142 ehci_hcd
[ 12.556377] usb usb2: SerialNumber: ci_hdrc.1
[ 12.749658] usb usb1-port1: over-current condition
[ 12.769836] hub 2-0:1.0: USB hub found
[ 12.829586] hub 2-0:1.0: 1 port detected
[ 12.919654] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 13.160772] usb 1-1: New USB device found, idVendor=abcd, idProduct=1234, bcdDevice= 1.00
[ 13.169013] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 13.176232] usb 1-1: Product: UDisk
[ 13.180708] usb 1-1: Manufacturer: General
[ 13.184899] usb 1-1: SerialNumber: Љ
[ 13.219606] usb 2-1: new high-speed USB device number 2 using ci_hdrc
[ 13.401556] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 13.470211] usb 2-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 13.478438] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 13.599194] hub 2-1:1.0: USB hub found
[ 13.623275] scsi host0: usb-storage 1-1:1.0
[ 13.705233] hub 2-1:1.0: 4 ports detected
[ 14.079588] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc
[ 14.240950] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00
[ 14.249355] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 14.256743] usb 2-1.1: Product: 802.11n WLAN Adapter
[ 14.261738] usb 2-1.1: Manufacturer: Realtek
[ 14.266015] usb 2-1.1: SerialNumber: 00e04c000001
[ 14.650731] scsi 0:0:0:0: Direct-Access General UDisk 5.00 PQ: 0 ANSI: 2
[ 14.701328] sd 0:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB)
[ 14.744960] sd 0:0:0:0: [sda] Write Protect is off
[ 14.784446] sd 0:0:0:0: [sda] No Caching mode page found
[ 14.789851] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 14.867727] sda:
[ 14.893472] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 15.639597] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 15.672277] Bluetooth: Core ver 2.22
[ 15.684323] NET: Registered protocol family 31
[ 15.688820] Bluetooth: HCI device and connection manager initialized
[ 15.726608] Bluetooth: HCI socket layer initialized
[ OK ] Found device [ 15.745173] Bluetooth: L2CAP socket layer initialized
/dev/mmcblk0p5.
[ 15.761909] Bluetooth: SCO socket layer initialized
[ 15.807461] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 15.864147] usbcore: registered new interface driver btusb
[ 15.872414] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
[ 15.886246] Bluetooth: hci0: RTL: rom_version status=0 version=1
[ 15.892383] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin
[ 15.901621] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin
[ 15.908223] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723b_config.bin failed with error -2
[ 15.917496] Bluetooth: hci0: RTL: cfg_sz -2, total sz 22496
[ 15.953472] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[ OK ] Found device /dev/mmcblk0p6.
[ 16.497168] RTL871X: module init start
[ 16.501032] RTL871X: rtl8723bu BT-Coex version = BTCOEX20140507-4E40
[ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
[ 16.689676] RTL871X: rtw_ndev_init(wlan0)
Activating swap /dev/mmcblk0p5...
[ 16.706799] RTL871X: rtw_ndev_init(wlan1)
[ 16.723236] usbcore: registered new interface driver rtl8723bu
[ 16.729157] RTL871X: module init ret=0
[ 16.753952] Bluetooth: hci0: RTL: fw version 0x0e2f9f73
Starting File System Check on /dev/mmcblk0p6...
Starting Load/Save RF Kill Switch Status...
[ 17.592955] Adding 262140k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:262140k SSDsc
[ 17.752574] usbcore: registered new interface driver rtl8xxxu
[ OK ] Activated swap /dev/mmcblk0p5.
[ OK ] Reached target Swap.
[ OK ] Started Load/Save RF Kill Switch Status.
[ OK ] Finished Helper to synchronize boot up for ifupdown.
[ OK ] Finished File System Check on /dev/mmcblk0p6.
Mounting /mnt/data...
[ 19.266831] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: discard
[ OK ] Mounted /mnt/data.
Mounting /var/log...
[ OK ] Mounted /var/log.
[ OK ] Reached target Local File Systems.
[ OK ] Started ifup for eth0.
[ OK ] Started ifup for eth1.
Starting Flush Journal to Persistent Storage...
Starting prepare mounts and symlinks to config files...
[ 19.760587] systemd-journald[121]: Received client request to flush runtime journal.
[ 19.825004] systemd-journald[121]: File /var/log/journal/c6e020b323ad4d2ebb8a1415d9658cbf/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Finished prepare mounts and symlinks to config files.
Starting Create Volatile Files and Directories...
[ OK ] Finished Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Monitor directorie… templates for wb-mqtt-serial.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Paths.
[ OK ] Reached target Timers.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Listening on fcgiwrap Socket.
[ OK ] Listening on KNX Daemon (socket).
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Bluetooth service...
[ OK ] Started Regular background program processing daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Network Manager...
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting Authorization Manager...
Starting User Login Management...
[ OK ] Started watch config files.
Starting Initialize Wiren Board Device Tree overlays...
[ OK ] Started Generates wb-mqtt-… UI schema for wb-mqtt-confed.
Starting Avahi mDNS/DNS-SD Stack...
[ 25.016967] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 25.022436] Bluetooth: BNEP filters: protocol multicast
[ 25.107905] Bluetooth: BNEP socket layer initialized
Starting WPA supplicant...
[ OK ] Started Authorization Manager.
[ OK ] Started Bluetooth service.
[ OK ] Reached target Bluetooth.
Starting Modem Manager...
Starting Hostname Service...
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started WPA supplicant.
[ OK ] Started User Login Management.
[ OK ] Started Modem Manager.
[ 32.909801] SMSC LAN8710/LAN8720 2188000.ethernet-2:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet-2:00, irq=POLL)
[ OK ] Started Hostname Service.
[ 35.129974] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[ 35.887330] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 43.522422] Micrel KSZ8081 or KSZ8091 2188000.ethernet-2:03: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=2188000.ethernet-2:03, irq=POLL)
[ **] (2 of 3) A start job is running for Network Manager (49s / 1min 49s)
[*** ] (1 of 3) A start job is running for…a Check Snapshots (53s / no limit)
[ OK ] Finished Initialize Wiren Board Device Tree overlays.
Starting Raise network interfaces...
Starting Power on GSM modem...
Starting KNXD Configurator for Wiren Board...
[ OK ] Finished Raise network interfaces.
[ INFO ] Skipped Power on GSM modem.
[ OK ] Started Network Manager.
[ OK ] Reached target Network.
Starting Network Manager Wait Online...
Starting dnsmasq - A light…DHCP and caching DNS server...
Starting Access point and …rver for Wi-Fi and Ethernet...
Starting KNX Daemon...
Starting Mosquitto MQTT Broker...
Starting Network Time Service...
Starting OpenBSD Secure Shell server...
Starting Permit User Sessions...
[ OK ] Started Network connection…rvice for Wiren Board devices.
Starting MQTT Driver for ADC...
Starting MQTT Driver for GPIO-controlled switches...
[ OK ] Started MQTT Driver for serial devices.
[ OK ] Started Kernel 1-Wire MQTT driver for WB-HomA.
[ OK ] Started KNX Daemon.
[ OK ] Finished KNXD Configurator for Wiren Board.
[ INFO ] Skipped dnsmasq - A lightw…t DHCP and caching DNS server.
[ INFO ] Skipped Access point and a…server for Wi-Fi and Ethernet.
обрезал последние несколько строк из-за ограничений редактора.
На флешке нет таблицы разделов. Опишите процесс подготовки флешки. В какой ОС это делаете и какое ПО используете?
Видел. Это было выделено в моем стартовом посте.
-
Купил новую флэшку 32ГБ, согласно статье Форматирование USB-накоптеля в FAT32 — Wiren Board отформатировал в FAT32 в Windows, скопировал прошивку, отмонтировал.
-
Вижу эту ошибку. Пробую еще раз. Та же флэшка, тот же способ.
-
Вижу эту ошибку. Покупаю новую флэшку, 7ГБ. Пробую тем же способом.
-
Ваш коллега выше давал ссылку на другой тикет Не подключается к WEB UI и SSH - #14 от пользователя BrainRoot. Согласно ему, на самом контроллере отформатировал флэшку 7ГБ, скопировал туда прошивку, проверил хэш, отмонтировал, перезагрузился. После нормальной загрузки контроллера примонтировал флэшку, убедился, что файл в корне на месте и называется корректно.
Все 4 способа приводили к одной и той же ошибке
USB device not accepting new address (error=22)
и
** No partition table - usb 0 **
Довольно инетерсно…
А что возвращает
fw_printenv
На контроллере?
Ну и - выполните
apt update
apt install u-boot-wb6
u-boot-install-wb
fw_printenv
_decr_timeout=setexpr fw_timeout ${fw_timeout} - 1
_led_toggle_state=0
_usb_update_checkbutton=run _usb_update_print_msg ; run led_wait_init ; if run wait_button_up; then if run wait_button_down; then run _usb_update_start; fi; fi
_usb_update_checkfile=if load ${fw_dev} ${loadaddr} ${fw_file} 1 ; then run _usb_update_checkbutton ; elif load ${fw_dev} ${loadaddr} ${fw_reset_file} 1 ; then setenv fw_file ${fw_reset_file}; run _usb_update_checkbutton ; fi
_usb_update_print_msg=echo ; echo '##############################' ; echo '# Detected USB flash drive with update file' ; echo "# Filename: ${fw_file}" ; echo "# Press a FW key if you want to update firmware from this file" ; echo "# or wait 3 seconds to boot normally." ; echo "##############################"
_usb_update_start=run led_fw_init; echo USB update procedure start; run do_usb_update
_wait_loop=run led_wait_toggle ; sleep 0.2 ; run _decr_timeout
addoverlay=if ${fdt_load_continue} && load mmc ${mmcdev}:${mmcpart} ${fdt_overlay_addr} ${fdt_overlays_dir}/${ovl}.dtbo; then echo Applying DT overlay ${ovl};if fdt apply ${fdt_overlay_addr}; then true; else echo Failed to apply overlay ${ovl};setenv fdt_load_continue false;fi;fi
altbootcmd=if test ${mmcpart} -eq 2; then echo Switching to rootfs on partition 3;setenv mmcpart 3;else; echo Switching to rootfs on partition 2;setenv mmcpart 2;fi;setenv bootcount 0;saveenv; boot
baudrate=115200
board_name=WB
board_rev=6UL
bootcmd=run maybe_usbupdate;mmc dev ${mmcdev};if mmc rescan; then echo SD/MMC found on device ${mmcdev};if run loadbootenv; then run bootenv; fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt; run mmcboot; fi;fi;
bootdelay=3
bootenv=echo Importing environment from ${loadaddr}...; env import -t ${loadaddr} ${filesize};echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;
bootlimit=3
bootrestore=echo Restoring minimal partition table and bootloader; setexpr RESTOREBOOT_SIZE *$bootrestore_size / 0x200 ; setexpr RESTOREBOOT_START *$bootrestore_start ; mmc write $RESTOREBOOT_START 2 $RESTOREBOOT_SIZE ; mw.l $bootrestore_flag 0 ; led red on ; echo Done! Now do a power cycle ; reset
bootrestore_flag=0x82fffffc
bootrestore_size=0x82fffff8
bootrestore_start=0x82fffff4
console=ttymxc0
do_usb_update=echo Checking if ubootenv part is present; if fsfitxtract ${fw_dev} ${fw_file} ubootenv ${loadaddr}; then run bootenv; else echo Extracting kernel; fsfitxtract ${fw_dev} ${fw_file} kernel ${loadaddr}; echo Extracting DTB; fsfitxtract ${fw_dev} ${fw_file} dtb ${fdt_addr}; setenv optargs ${optargs} bootmode=usbupdate,${fw_file}; run setbootargs; bootz ${loadaddr} - ${fdt_addr}; fi;
eth1addr=54:10:ec:34:1e:be
ethaddr=54:10:ec:34:61:52
fdt_addr=0x83000000
fdt_dir=/boot/dtbs
fdt_extra_overlay_offset=0x7e0
fdt_extra_overlay_size=0x20
fdt_file=/boot/dtbs/imx6ul-wirenboard61.dtb
fdt_maxsize=0x20000
fdt_overlay_addr=0x84000000
fdt_overlays_dir=/boot/overlays
fw_dev=usb 0:1
fw_file=wb6_update.fit
fw_reset_file=wb6_update_FACTORYRESET.fit
fw_timeout="14"
ip_dyn=yes
kernel_mmcdev=0
led_fw_init=led green on; led red off;
led_nofw_init=led green off; led red on;
led_wait_init=led red on ; led green on
led_wait_toggle=if test ${_led_toggle_state} -eq 0; then led green on; led red on; else led green off; led red off; fi; setexpr _led_toggle_state ${_led_toggle_state} ^ 1
loadaddr=0x82000000
loadbootenv=load mmc ${mmcdev}:${mmcpart} ${loadaddr} /boot/uEnv.txt
loadfdt=run loadfdtandoverlays
loadfdtandoverlays=mmc read ${fdt_overlay_addr} ${fdt_extra_overlay_offset} ${fdt_extra_overlay_size};if fdt addr ${fdt_overlay_addr}; then setenv fdt_extra_overlay_addr ${fdt_overlay_addr};setexpr fdt_extra_overlay_size_bytes ${fdt_extra_overlay_size} * 0x200;setexpr fdt_overlay_addr ${fdt_overlay_addr} + ${fdt_extra_overlay_size_bytes};echo Reading overlays list from eMMC;fdt get value fdt_overlays /fragment/__overlay__ overlays;echo Reading factory fdt name from eMMC;fdt get value fdt_name_factory /fragment/__overlay__ factory-fdt;fi;run loadmainfdt;fdt addr ${fdt_addr} ${fdt_maxsize};setenv fdt_load_continue true;for ovl in ${fdt_overlays}; do run addoverlay;done;if ${fdt_load_continue} && test -n ${fdt_extra_overlay_addr}; then echo Applying extra overlay;if fdt apply ${fdt_extra_overlay_addr}; then true; else echo Failed to apply extra overlay;setenv fdt_load_continue false;fi;fi;if ${fdt_load_continue}; then true; else echo Some overlays are not applied, booting in failsafe;run loadmainfdt;fdt addr ${fdt_addr} ${fdt_maxsize};fdt set / wirenboard-boot-failsafe;fi;
loadmainfdt=if test -n ${fdt_file_override} && echo Loading fdt_file_override ${fdt_file_override} && load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file_override}; then true; else if test -n ${fdt_name_factory} && echo Loading factory fdt ${fdt_name_factory} && load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_dir}/${fdt_name_factory}.dtb;then true; else echo Loading fdt_file ${fdt_file};load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file};fi;fi;
loadzimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} /boot/zImage
maybe_usbupdate=echo Checking if there is a USB storage with update file ${fw_file}; regulator dev usb1_vbus; regulator enable; usb start; if usb storage; then run _usb_update_checkfile ; fi; run led_nofw_init ; echo No USB update detected, continuing boot
mmcargs=setenv optargs ${optargs} root=/dev/mmcblk${kernel_mmcdev}p${mmcpart} rootwait ro; run setbootargs
mmcboot=echo Booting from mmc ...; run mmcargs; bootz ${loadaddr} - ${fdt_addr}
mmcdev=1
mmcpart=3
netargs=setenv optargs ${optargs} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp; run setbootargs
netboot=echo Booting from net ...; run netargs; tftp zImage; if ${get_cmd} ${fdt_addr} ${fdt_file}; then bootz ${loadaddr} - ${fdt_addr}; else bootz; fi;
not_timeout=test 0x${fw_timeout} -gt 0
ramboot=echo Programming fuses ...; fuse prog -y 0 5 0x4860; fuse prog -y 0 6 0x10; echo Booting kernel from RAM ...; run setbootargs; bootz ${loadaddr} - ${fdt_addr};
read_button=gpio qi GPIO5_10
setbootargs=setenv bootargs console=${console},${baudrate} ${optargs}
videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0
wait_button_down=until run read_button && run not_timeout ; do run _wait_loop; done; run not_timeout
wait_button_up=while run read_button && run not_timeout ; do run _wait_loop; done; run not_timeout
bootcount=0
upgrade_available=0
u-boot-install-wb
Das U-Boot installer for Wiren Board
You are about to install U-boot image '/usr/lib/u-boot/mx6ul_wirenboard6/u-boot-with-spl.imx' on '/dev/mmcblk0' (platform wb6)
Do you want to continue (y/n)?y
Writing U-boot image '/usr/lib/u-boot/mx6ul_wirenboard6/u-boot-with-spl.imx' on '/dev/mmcblk0' (options 'bs=512 seek=2')
831+1 записей получено
831+1 записей отправлено
425816 байт (426 kB, 416 KiB) скопирован, 0,628564 s, 677 kB/s
Syncing device
Пришлите вывод команд:
blkid
и
lsblk | grep sd
при вставленных флешках
blkid
/dev/mmcblk0p1: PARTUUID="f31e1617-01"
/dev/mmcblk0p2: LABEL="rootfs" UUID="8371addb-38f1-4bec-a3e7-6dd49c79032a" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="f31e1617-02"
/dev/mmcblk0p3: UUID="7a6217e7-c8f0-4bc6-a5dd-58cec811dec1" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="f31e1617-03"
/dev/mmcblk0p5: UUID="7cd0b6d4-b3f8-49a2-85fa-dae21de9aa37" TYPE="swap" PARTUUID="f31e1617-05"
/dev/mmcblk0p6: LABEL="data" UUID="6b523279-10f0-480a-af0d-bc10bcc779c9" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="f31e1617-06"
/dev/sda: UUID="6370-0423" BLOCK_SIZE="512" TYPE="vfat"
lsblk | grep sd
sda 8:0 1 7,5G 0 disk
root@wirenboard-AKQ2UEDD:~#
Не вижу раздела на флешке. Показывает только сам диск.
1 лайк
Совершенно верно…
Тоже самое с другой флешкой посмотрите.
blkid
/dev/mmcblk0p2: LABEL="rootfs" UUID="8371addb-38f1-4bec-a3e7-6dd49c79032a" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="f31e1617-02"
/dev/mmcblk0p3: UUID="7a6217e7-c8f0-4bc6-a5dd-58cec811dec1" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="f31e1617-03"
/dev/mmcblk0p5: UUID="7cd0b6d4-b3f8-49a2-85fa-dae21de9aa37" TYPE="swap" PARTUUID="f31e1617-05"
/dev/mmcblk0p6: LABEL="data" UUID="6b523279-10f0-480a-af0d-bc10bcc779c9" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="f31e1617-06"
/dev/mmcblk0p1: PARTUUID="f31e1617-01"
/dev/sda1: LABEL="KINGSTON" UUID="1618-C379" BLOCK_SIZE="512" TYPE="vfat" PARTUUID="02f5df23-01"
lsblk | grep sd
sda 8:0 1 28,9G 0 disk
└─sda1 8:1 1 28,9G 0 part
Попробуйте обновиться с этой флешкой и пришлите вывод консоли.
Какого типа раздел, кстати?
U-Boot SPL 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
DRAM init ok, rows:15, ncs:1, size: 512MB
.p0_mpdgctrl0 = 0x01120110
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3c3e
.p0_mpwrdlctl = 0x3f3f3734
.p0_mpwldectrl0 = 0x0008000a
.p0_mpwldectrl1 = 0x000b000b
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot SPL 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
DRAM init ok, rows:15, ncs:1, size: 512MB
.p0_mpdgctrl0 = 0x010d010b
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3d3e
.p0_mpwrdlctl = 0x3f3f3835
.p0_mpwldectrl0 = 0x00080008
.p0_mpwldectrl1 = 0x00090009
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 45C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 512 MiB
MMC: FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Loading Environment from MMC... OK
Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program
## Info: input data size = 43 = 0x2B
bootcount=0
mmcpart=3
upgrade_available=0
Environment size: 43/8188 bytes
## Resetting to default environment
## Info: input data size = 43 = 0x2B
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
## Info: input data size = 4285 = 0x10BD
switch to partitions #0, OK
mmc1(part 0) is current device
eMMC found on device 1
Press FW button to enter firmware update mode
...
Entering firmware update mode.
Checking if ubootenv part is present
## Loading FIT header to 0x82000000 ...
** File not found .wb-restore/factoryreset.fit **
Read failed: -1Extracting kernel
## Loading FIT header to 0x82000000 ...
** File not found .wb-restore/factoryreset.fit **
Read failed: -1Extracting DTB
## Loading FIT header to 0x83000000 ...
** File not found .wb-restore/factoryreset.fit **
Read failed: -1zimage: Bad magic!
ERROR: Failed to enter update mode!
ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
Bus usb@2184000: USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found
scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80
USB device not accepting new address (error=22)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
No storage devices, perhaps not 'usb start'ed..?
No USB update detected, continuing boot
322 bytes read in 3 ms (104.5 KiB/s)
Importing environment from 0x82000000...
Checking if uenvcmd is set ...
Running default loadzimage ...
6304344 bytes read in 274 ms (21.9 MiB/s)
MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK
Reading overlays list from eMMC
Reading factory fdt name from eMMC
Loading factory fdt imx6ul-wirenboard660
46098 bytes read in 5 ms (8.8 MiB/s)
670 bytes read in 3 ms (217.8 KiB/s)
Applying DT overlay wb6-gsm-sim800
597 bytes read in 4 ms (145.5 KiB/s)
Applying DT overlay wb6-wifi-rtl8723bu
509 bytes read in 4 ms (124 KiB/s)
Applying DT overlay wb6-noradio
334 bytes read in 3 ms (108.4 KiB/s)
Applying DT overlay wb6-eth1
254 bytes read in 4 ms (61.5 KiB/s)
Applying DT overlay temp-industrial
Applying extra overlay
Booting from mmc ...
Kernel image @ 0x82000000 [ 0x000000 - 0x603258 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Device Tree to 9ef77000, end 9ef99fff ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.35-wb142 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Thu Jul 20 07:59:09 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.6.0 (i.MX6UL/ULL)
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x9f000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=update_auto root=/dev/mmcblk0p3 rootwait ro
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 489364K/524288K available (8192K kernel code, 728K rwdata, 2776K rodata, 1024K init, 283K bss, 18540K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x234/0x3dc with crng_init=0
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000059] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002724] Console: colour dummy device 80x30
[ 0.002785] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.002822] pid_max: default: 32768 minimum: 301
[ 0.003213] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.003250] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004938] CPU: Testing write buffer coherency: ok
[ 0.006173] Setting up static identity map for 0x80100000 - 0x80100078
[ 0.007056] devtmpfs: initialized
[ 0.024503] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.025004] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.025050] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.026425] pinctrl core: initialized pinctrl subsystem
[ 0.028414] NET: Registered protocol family 16
[ 0.030632] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.032578] thermal_sys: Registered thermal governor 'step_wise'
[ 0.032849] cpuidle: using governor menu
[ 0.195434] vdd1p1: supplied by regulator-dummy
[ 0.206470] vdd3p0: supplied by regulator-dummy
[ 0.217537] cpu: supplied by regulator-dummy
[ 0.228586] vddsoc: supplied by regulator-dummy
[ 0.558949] No ATAGs?
[ 0.559010] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.559029] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.559599] debugfs: Directory 'dummy-iomuxc-gpr@20e4000' with parent 'regmap' already present!
[ 0.560215] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver
[ 0.561709] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/bus@2200000/iomuxc-snvs@2290000
[ 0.561746] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.604254] mxs-dma 1804000.dma-apbh: initialized
[ 0.609474] SCSI subsystem initialized
[ 0.609980] usbcore: registered new interface driver usbfs
[ 0.610104] usbcore: registered new interface driver hub
[ 0.610210] usbcore: registered new device driver usb
[ 0.611019] gpio-48 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.611148] gpio-49 (i2c_rtc): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.612080] i2c-gpio i2c_rtc: using lines 48 (SDA) and 49 (SCL)
[ 0.612812] gpio-76 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.612939] gpio-67 (i2c_eeprom1): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.613615] i2c-gpio i2c_eeprom1: using lines 76 (SDA) and 67 (SCL)
[ 0.614321] gpio-70 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.614447] gpio-71 (i2c_eeprom2): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.615052] i2c-gpio i2c_eeprom2: using lines 70 (SDA) and 71 (SCL)
[ 0.616603] gpio-30 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 0.616952] i2c i2c-1: IMX I2C adapter registered
[ 0.617686] mc: Linux media interface: v0.10
[ 0.617799] videodev: Linux video capture interface: v2.00
[ 0.617927] pps_core: LinuxPPS API ver. 1 registered
[ 0.617946] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.617997] PTP clock support registered
[ 0.618608] Advanced Linux Sound Architecture Driver Initialized.
[ 0.620725] clocksource: Switched to clocksource mxc_timer1
[ 0.638401] NET: Registered protocol family 2
[ 0.639650] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.639752] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.639857] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.639961] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.640151] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.640205] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.640531] NET: Registered protocol family 1
[ 0.641581] RPC: Registered named UNIX socket transport module.
[ 0.641621] RPC: Registered udp transport module.
[ 0.641640] RPC: Registered tcp transport module.
[ 0.641654] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.642731] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.645538] Initialise system trusted keyrings
[ 0.646014] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.657552] NFS: Registering the id_resolver key type
[ 0.657636] Key type id_resolver registered
[ 0.657655] Key type id_legacy registered
[ 0.896761] Key type asymmetric registered
[ 0.896804] Asymmetric key parser 'x509' registered
[ 0.896927] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.896949] io scheduler mq-deadline registered
[ 0.896967] io scheduler kyber registered
[ 0.908734] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[ 0.908784] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 0.912722] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX
[ 1.577566] printk: console [ttymxc0] enabled
[ 1.584055] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 58, base_baud = 5000000) is a IMX
[ 1.594651] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 59, base_baud = 5000000) is a IMX
[ 1.638295] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129)
[ 1.645725] random: fast init done
[ 1.649676] random: crng init done
[ 1.689666] brd: module loaded
[ 1.707834] loop: module loaded
[ 1.711413] at24 5-0050: supply vcc not found, using dummy regulator
[ 1.722850] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.729833] at24 6-0050: supply vcc not found, using dummy regulator
[ 1.741250] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.751209] libphy: Fixed MDIO Bus: probed
[ 1.758158] pps pps0: new PPS source ptp0
[ 1.798363] libphy: fec_enet_mii_bus: probed
[ 1.803878] fec 20b4000.ethernet ethFEC0: registered PHC device 0
[ 1.931427] pps pps1: new PPS source ptp1
[ 1.938005] libphy: fec_enet_mii_bus: probed
[ 1.946715] fec 2188000.ethernet ethFEC1: registered PHC device 1
[ 1.953830] PPP generic driver version 2.4.2
[ 1.958516] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.965159] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.970929] usbcore: registered new interface driver usb-storage
[ 1.977179] usbcore: registered new interface driver usbserial_generic
[ 1.983835] usbserial: USB Serial support registered for generic
[ 2.032709] rtc rtc0: invalid alarm value: 2023-09-01T25:06:00
[ 2.038972] rtc-pcf8563 4-0051: registered as rtc0
[ 2.055715] rtc-pcf8563 4-0051: setting system clock to 2023-09-07T13:23:01 UTC (1694092981)
[ 2.073976] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1
[ 2.080415] i2c /dev entries driver
[ 2.087234] lm75 4-0048: supply vs not found, using dummy regulator
[ 2.098843] lm75 4-0048: hwmon0: sensor 'lm75b'
[ 2.218912] sdhci: Secure Digital Host Controller Interface driver
[ 2.225192] sdhci: Copyright(c) Pierre Ossman
[ 2.229562] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.244371] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.252245] usbcore: registered new interface driver usbhid
[ 2.257847] usbhid: USB HID core driver
[ 2.273134] Initializing XFRM netlink socket
[ 2.277540] mmc0: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA
[ 2.285865] NET: Registered protocol family 10
[ 2.293640] Segment Routing with IPv6
[ 2.297773] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.305806] NET: Registered protocol family 17
[ 2.310983] Key type dns_resolver registered
[ 2.319298] registered taskstats version 1
[ 2.324079] Loading compiled-in X.509 certificates
[ 2.346757] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[ 2.358668] of_cfs_init
[ 2.361464] of_cfs_init: OK
[ 2.369290] ALSA device list:
[ 2.372335] No soundcards found.
[ 2.376043] Waiting for root device /dev/mmcblk0p3...
[ 2.386033] mmc0: new DDR MMC card at address 0001
[ 2.391802] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[ 2.396732] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
[ 2.403178] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
[ 2.409426] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB, chardev (245:0)
[ 2.420144] mmcblk0: p1 p2 p3 p4 < p5 p6 >
[ 2.447979] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem
[ 2.455382] EXT4-fs (mmcblk0p3): write access will be enabled during recovery
[ 2.650876] EXT4-fs (mmcblk0p3): recovery complete
[ 2.660791] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.669022] VFS: Mounted root (ext4 filesystem) readonly on device 179:3.
[ 2.677683] devtmpfs: mounted
[ 2.682373] Freeing unused kernel memory: 1024K
[ 2.687186] Run /sbin/init as init process
[ 3.112592] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 3.137041] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
Device Boot Start End Sectors Size Id Type
/dev/sda1 * 64 60538879 60538816 28.9G c W95 FAT32 (LBA)
Смотрите, я смотрю в дебаг-консоль и нажимаю, удерживая на сек, на строчке
Press FW button to enter firmware update mode
…
Контроллер кратко пикает и продолжается загрузка дальше. Нет этих символов решеток как на скриншотах по вашей ссылке. Может что-то с правами на файл на флэшке? Сейчас заново подготовил флэш по инструкции Не подключается к WEB UI и SSH - #13 от пользователя Haggard
U-Boot SPL 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
DRAM init ok, rows:15, ncs:1, size: 512MB
.p0_mpdgctrl0 = 0x01140112
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f3d3f
.p0_mpwrdlctl = 0x3f3f3836
.p0_mpwldectrl0 = 0x00080008
.p0_mpwldectrl1 = 0x00090009
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2021.10-wb1.6.0-g9e72dde28f (Jul 11 2023 - 12:18:34 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 61C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 512 MiB
MMC: FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Loading Environment from MMC... OK
Will only keep env vars: mmcpart bootcount upgrade_available uenvcmd wb_webupd otp_program otp_aes_program
## Info: input data size = 43 = 0x2B
bootcount=0
mmcpart=3
upgrade_available=0
Environment size: 43/8188 bytes
## Resetting to default environment
## Info: input data size = 43 = 0x2B
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
## Info: input data size = 4285 = 0x10BD
switch to partitions #0, OK
mmc1(part 0) is current device
eMMC found on device 1
Press FW button to enter firmware update mode
.........
Entering firmware update mode.
Checking if ubootenv part is present
## Loading FIT header to 0x82000000 ...
** File not found .wb-restore/factoryreset.fit **
Read failed: -1Extracting kernel
## Loading FIT header to 0x82000000 ...
** File not found .wb-restore/factoryreset.fit **
Read failed: -1Extracting DTB
## Loading FIT header to 0x83000000 ...
** File not found .wb-restore/factoryreset.fit **
Read failed: -1zimage: Bad magic!
ERROR: Failed to enter update mode!
ERROR: /mnt/data/.wb-restore/factoryreset.fit missing or corrupt
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
Bus usb@2184000: USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found
scanning bus usb@2184200 for devices... EHCI timed out on TD - token=0x80008d80
USB device not accepting new address (error=22)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
No storage devices, perhaps not 'usb start'ed..?
No USB update detected, continuing boot
322 bytes read in 3 ms (104.5 KiB/s)
Importing environment from 0x82000000...
Checking if uenvcmd is set ...
Running default loadzimage ...
6304344 bytes read in 274 ms (21.9 MiB/s)
MMC read: dev # 1, block # 2016, count 32 ... 32 blocks read: OK
Reading overlays list from eMMC
Reading factory fdt name from eMMC
Loading factory fdt imx6ul-wirenboard660
46098 bytes read in 5 ms (8.8 MiB/s)
670 bytes read in 3 ms (217.8 KiB/s)
Applying DT overlay wb6-gsm-sim800
597 bytes read in 4 ms (145.5 KiB/s)
Applying DT overlay wb6-wifi-rtl8723bu
509 bytes read in 4 ms (124 KiB/s)
Applying DT overlay wb6-noradio
334 bytes read in 3 ms (108.4 KiB/s)
Applying DT overlay wb6-eth1
254 bytes read in 4 ms (61.5 KiB/s)
Applying DT overlay temp-industrial
Applying extra overlay
Booting from mmc ...
Kernel image @ 0x82000000 [ 0x000000 - 0x603258 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Device Tree to 9ef77000, end 9ef99fff ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.35-wb142 (jenkins@wbdevenv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Thu Jul 20 07:59:09 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Wiren Board rev. 6.6.0 (i.MX6UL/ULL)
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x9f000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=update_auto root=/dev/mmcblk0p3 rootwait ro
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 489364K/524288K available (8192K kernel code, 728K rwdata, 2776K rodata, 1024K init, 283K bss, 18540K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated