Что значит не дописан?
Другая флешка, другая прошивка:
2021-09-09T14:00:35.000Z 167.7 MB 202109091359_stable_webupd_wb67.fit
U-Boot 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 35C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 1 GiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@02188000
Hit any key to stop autoboot: 0
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
USB0: USB EHCI 1.00
USB1: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Device 0: Vendor: General Rev: 5.00 Prod: UDisk
Type: Removable Hard Disk
Capacity: 31000.0 MB = 30.2 GB (63488000 x 512)
reading wb6_update.fit
** Unable to read file wb6_update.fit **
reading wb6_update_FACTORYRESET.fit
1 bytes read in 25 ms (0 Bytes/s)
##############################
# Detected USB flash drive with update file
# Filename: wb6_update_FACTORYRESET.fit
# Press a FW key if you want to update firmware from this file
# or wait 3 seconds to boot normally.
##############################
USB update procedure start
Checking if ubootenv part is present
## Loading FIT header to 0x82000000 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update_FACTORYRESET.fit
Skip 7965224 bytes of data
reading wb6_update_FACTORYRESET.fit
Skip 46158 bytes of data
reading wb6_update_FACTORYRESET.fit
Skip 4085 bytes of data
Skip 167836813 bytes of data
reading wb6_update_FACTORYRESET.fit
** wb6_update_FACTORYRESET.fit shorter than offset + len **
Can't find subimage 'ubootenv'
Extracting kernel
## Loading FIT header to 0x82000000 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update_FACTORYRESET.fit
reading wb6_update_FACTORYRESET.fit
U-Boot SPL 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31)
DRAM init ok, rows:16, ncs:1, size: 1024MB
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 1 GiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@02188000
Hit any key to stop autoboot: 0
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
USB0: USB EHCI 1.00
USB1: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Device 0: Vendor: General Rev: 5.00 Prod: UDisk
Type: Removable Hard Disk
Capacity: 31000.0 MB = 30.2 GB (63488000 x 512)
reading wb6_update.fit
** Unable to read file wb6_update.fit **
reading wb6_update_FACTORYRESET.fit
1 bytes read in 25 ms (0 Bytes/s)
##############################
# Detected USB flash drive with update file
# Filename: wb6_update_FACTORYRESET.fit
# Press a FW key if you want to update firmware from this file
# or wait 3 seconds to boot normally.
##############################
USB update procedure start
Checking if ubootenv part is present
## Loading FIT header to 0x82000000 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update_FACTORYRESET.fit
Skip 7965224 bytes of data
reading wb6_update_FACTORYRESET.fit
Skip 46158 bytes of data
reading wb6_update_FACTORYRESET.fit
Skip 4085 bytes of data
Skip 167836813 bytes of data
reading wb6_update_FACTORYRESET.fit
** wb6_update_FACTORYRESET.fit shorter than offset + len **
Can't find subimage 'ubootenv'
Extracting kernel
## Loading FIT header to 0x82000000 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update_FACTORYRESET.fit
reading wb6_update_FACTORYRESET.fit
U-Boot SPL 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31)
DRAM init ok, rows:16, ncs:1, size: 1024MB
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 39C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 1 GiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@02188000
Hit any key to stop autoboot: 0
=>
U-Boot SPL 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31)
DRAM init ok, rows:16, ncs:1, size: 1024MB
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 39C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 1 GiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@02188000
Hit any key to stop autoboot: 0
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
USB0: USB EHCI 1.00
USB1: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Device 0: Vendor: General Rev: 5.00 Prod: UDisk
Type: Removable Hard Disk
Capacity: 31000.0 MB = 30.2 GB (63488000 x 512)
reading wb6_update.fit
** Unable to read file wb6_update.fit **
reading wb6_update_FACTORYRESET.fit
1 bytes read in 25 ms (0 Bytes/s)
##############################
# Detected USB flash drive with update file
# Filename: wb6_update_FACTORYRESET.fit
# Press a FW key if you want to update firmware from this file
# or wait 3 seconds to boot normally.
##############################
No USB update detected, continuing boot
switch to partitions #0, OK
mmc0(part 0) is current device
SD/MMC found on device 0
324 bytes read in 73 ms (3.9 KiB/s)
Importing environment from 0x82000000...
Checking if uenvcmd is set ...
Running default loadzimage ...
5126192 bytes read in 358 ms (13.7 MiB/s)
MMC read: dev # 0, block # 2016, count 32 ... 32 blocks read: OK
Reading overlays list from eMMC
Reading factory fdt name from eMMC
Loading factory fdt imx6ul-wirenboard680
46446 bytes read in 100 ms (453.1 KiB/s)
** e
U-Boot SPL 2017.03-1.2.0-gf92dee6f51 (Jun 02 2021 - 13:45:31)
DRAM init ok, rows:16, ncs:1, size: 1024MB
Trying to boot from MMC1
Warning - USDHC2 controller not supporting