Пробую.
U-Boot 2017.03-1.0.2-g6ee0824fba (May 27 2019 - 16:14:52 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 53C
Reset cause: POR
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
EEPROM #0 MAC: 04:91:62:c2:33:30
EEPROM #1 MAC: 04:91:62:c2:41:59
Net: eth0: ethernet@02188000
Hit any key to stop autoboot: 0
Checking if there is a USB storage with update file wb6_update.fit
dev: usb1_vbus @ regulator@0
starting USB...
USB0: USB EHCI 1.00
USB1: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Device 0: Vendor: Kingston Rev: 1.00 Prod: DataTraveler 2.0
Type: Removable Hard Disk
Capacity: 1919.0 MB = 1.8 GB (3930112 x 512)
reading wb6_update.fit
** Unable to read file wb6_update.fit **
reading wb6_update_FACTORYRESET.fit
1 bytes read in 19 ms (0 Bytes/s)
##############################
# Detected USB flash drive with update file
# Filename: wb6_update_FACTORYRESET.fit
# Press a FW key if you want to update firmware from this file
# or wait 3 seconds to boot normally.
##############################
USB update procedure start
Checking if ubootenv part is present
## Loading FIT header to 0x82000000 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update_FACTORYRESET.fit
FAT: Misaligned buffer address (820010c8)
Skip 7928976 bytes of data
reading wb6_update_FACTORYRESET.fit
FAT: Misaligned buffer address (8200042c)
Skip 46505 bytes of data
reading wb6_update_FACTORYRESET.fit
FAT: Misaligned buffer address (82000e74)
Skip 4653 bytes of data
Skip 174093992 bytes of data
reading wb6_update_FACTORYRESET.fit
FAT: Misaligned buffer address (82000584)
** wb6_update_FACTORYRESET.fit shorter than offset + len **
Can't find subimage 'ubootenv'
Extracting kernel
## Loading FIT header to 0x82000000 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT strings to 0x82000028 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT struct to 0x82000100 ...
reading wb6_update_FACTORYRESET.fit
FAT: Misaligned buffer address (820010c8)
reading wb6_update_FACTORYRESET.fit
7945616 bytes read in 4914 ms (1.5 MiB/s)
Description: Update kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x82000300
Data Size: 7928976 Bytes = 7.6 MiB
Architecture: ARM
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Hash algo: sha1
Hash value: 47f6419e0d5d8326c41b16761827dc3d746fec78
## Verifying ... sha1+
Loading part 0 ... OK
Extracting DTB
## Loading FIT header to 0x83000000 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT strings to 0x83000028 ...
reading wb6_update_FACTORYRESET.fit
## Loading FIT struct to 0x83000100 ...
reading wb6_update_FACTORYRESET.fit
FAT: Misaligned buffer address (830010c8)
Skip 7928976 bytes of data
reading wb6_update_FACTORYRESET.fit
FAT: Misaligned buffer address (8300042c)
reading wb6_update_FACTORYRESET.fit
63589 bytes read in 727 ms (85 KiB/s)
Description: Update DTB
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x83000440
Data Size: 46505 Bytes = 45.4 KiB
Architecture: ARM
Hash algo: sha1
Hash value: ef9dd3fe2b348fb8eb9f150b9dc2e27d6899e823
## Verifying ... sha1+
Loading part 0 ... OK
Kernel image @ 0x82000000 [ 0x000000 - 0x78fc90 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Device Tree to 9ef48000, end 9ef565a8 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.22-wb6_initramfs (root@WB-buildserver) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #2 SMP Tue Feb 1 16:52:01 MSK 2022
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt:Machine model: Wiren Board init (i.MX6UL/ULL)
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 14 pages/cpu @cfbd0000 s25932 r8192 d23220 u57344
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttymxc0,115200 bootmode=usbupdate,wb6_update_FACTORYRESET.fit
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 506760K/524288K available (5120K kernel code, 202K rwdata, 1576K rodata, 5120K init, 295K bss, 17528K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xb0000000 - 0xd0000000 ( 512 MB)
[ 0.000000] modules : 0xaf000000 - 0xb0000000 ( 16 MB)
[ 0.000000] .text : 0xb0008000 - 0xb0600000 (6112 kB)
[ 0.000000] .init : 0xb0800000 - 0xb0d00000 (5120 kB)
[ 0.000000] .data : 0xb0d00000 - 0xb0d32880 ( 203 kB)
[ 0.000000] .bss : 0xb0d34000 - 0xb0d7ddb0 ( 296 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000015] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000052] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002601] Console: colour dummy device 80x30
[ 0.002641] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.002673] pid_max: default: 32768 minimum: 301
[ 0.002866] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002892] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.004091] CPU: Testing write buffer coherency: ok
[ 0.004584] /cpus/cpu@0 missing clock-frequency property
[ 0.004623] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.004677] Setting up static identity map for 0x80100000 - 0x80100070
[ 0.007073] Brought up 1 CPUs
[ 0.007109] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[ 0.007125] CPU: All CPU(s) started in SVC mode.
[ 0.008340] devtmpfs: initialized
[ 0.034460] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.035144] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.035194] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.035373] pinctrl core: initialized pinctrl subsystem
[ 0.037429] NET: Registered protocol family 16
[ 0.037943] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.040614] cpuidle: using governor menu
[ 0.076058] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.076088] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.078327] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.118592] mxs-dma 1804000.dma-apbh: initialized
[ 0.123124] SCSI subsystem initialized
[ 0.123720] usbcore: registered new interface driver usbfs
[ 0.123899] usbcore: registered new interface driver hub
[ 0.124143] usbcore: registered new device driver usb
[ 0.125736] i2c-gpio i2c_rtc: using pins 48 (SDA) and 49 (SCL)
[ 0.126622] i2c-gpio i2c_eeprom1: using pins 76 (SDA) and 67 (SCL)
[ 0.127465] i2c-gpio i2c_eeprom2: using pins 70 (SDA) and 71 (SCL)
[ 0.128947] i2c i2c-1: IMX I2C adapter registered
[ 0.128991] i2c i2c-1: can't use DMA, using PIO instead.
[ 0.129411] pps_core: LinuxPPS API ver. 1 registered
[ 0.129435] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.129492] PTP clock support registered
[ 0.131880] clocksource: Switched to clocksource mxc_timer1
[ 0.155694] NET: Registered protocol family 2
[ 0.156890] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.157017] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.157173] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.157283] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.157341] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.157650] NET: Registered protocol family 1
[ 0.158461] RPC: Registered named UNIX socket transport module.
[ 0.158496] RPC: Registered udp transport module.
[ 0.158511] RPC: Registered tcp transport module.
[ 0.158525] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.727059] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.742221] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.744227] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.754689] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.754725] io scheduler noop registered (default)
[ 0.759897] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[ 0.759937] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 0.769038] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX
[ 1.323178] console [ttymxc0] enabled
[ 1.328700] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 55, base_baud = 5000000) is a IMX
[ 1.338974] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 56, base_baud = 5000000) is a IMX
[ 1.381801] imx_rngc 2284000.rngb: Freescale RNGC registered.
[ 1.416706] brd: module loaded
[ 1.435694] loop: module loaded
[ 1.443954] at24 5-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.455364] at24 6-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 1.462892] libphy: Fixed MDIO Bus: probed
[ 1.469342] 20b4000.ethernet supply phy not found, using dummy regulator
[ 1.477365] pps pps0: new PPS source ptp0
[ 1.510253] libphy: fec_enet_mii_bus: probed
[ 1.516525] fec 20b4000.ethernet eth0: registered PHC device 0
[ 1.641967] 2188000.ethernet supply phy not found, using dummy regulator
[ 1.762894] pps pps1: new PPS source ptp1
[ 1.767966] libphy: fec_enet_mii_bus: probed
[ 1.775897] fec 2188000.ethernet eth1: registered PHC device 1
[ 1.782477] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.789050] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.794908] usbcore: registered new interface driver cdc_acm
[ 1.800603] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.809088] usbcore: registered new interface driver usb-storage
[ 1.872375] rtc-pcf8563 4-0051: rtc core: registered rtc-pcf8563 as rtc0
[ 1.888512] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[ 1.897644] i2c /dev entries driver
[ 1.905834] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 1.913345] imx6ul-pinctrl 20e0000.iomuxc: pin MX6UL_PAD_SD1_DATA1 already requested by watchdog; cannot claim for watchdog_6x
[ 1.924899] imx6ul-pinctrl 20e0000.iomuxc: pin-114 (watchdog_6x) status -22
[ 1.931952] imx6ul-pinctrl 20e0000.iomuxc: could not request pin 114 (MX6UL_PAD_SD1_DATA1) from group wdggrp_6x on device 20e0000.iomuxc
[ 1.944369] gpio-wdt watchdog_6x: Error applying setting, reverse things back
[ 1.951560] gpio-wdt: probe of watchdog_6x failed with error -22
[ 1.959325] sdhci: Secure Digital Host Controller Interface driver
[ 1.965649] sdhci: Copyright(c) Pierre Ossman
[ 1.970038] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.041948] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[ 2.061504] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.069065] random: fast init done
[ 2.089533] usbcore: registered new interface driver usbhid
[ 2.097300] usbhid: USB HID core driver
[ 2.111578] NET: Registered protocol family 17
[ 2.122546] Registering SWP/SWPB emulation handler
[ 2.129591] registered taskstats version 1
[ 2.146570] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[ 2.169822] rtc-pcf8563 4-0051: setting system clock to 2023-05-24 13:53:17 UTC (1684936397)
[ 2.178313] of_cfs_init
[ 2.180967] of_cfs_init: OK
[ 2.189868] vdd3p0: disabling
[ 2.195042] vref-3v3: disabling
[ 2.200291] usb1_vbus: disabling
[ 2.212256] Freeing unused kernel memory: 5120K (b0800000 - b0d00000)
[ 2.227967] mmc0: new DDR MMC card at address 0001
[ 2.248063] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[ 2.262245] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
mount: mounting none on /dev/pts [ 2.272246] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
failed: No such file or directory
[ 2.292503] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB
[ 2.303292] mmcblk0: p1 p2 p3 p4 < p5 p6 >
Boot mode: usbupdate,wb6_update_FACTORYRESET.fit
Board is WB6, loading ci_hdrc_imx module
[ 2.542734] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 2.547680] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 2.581960] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 2.587642] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.594496] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.601726] usb usb1: Product: EHCI Host Controller
[ 2.606659] usb usb1: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd
[ 2.613322] usb usb1: SerialNumber: ci_hdrc.0
[ 2.619164] hub 1-0:1.0: USB hub found
[ 2.623164] hub 1-0:1.0: 1 port detected
[ 2.628660] 2184200.usb supply vbus not found, using dummy regulator
[ 2.639336] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 2.644426] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ 2.671970] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 2.677736] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.684610] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.691892] usb usb2: Product: EHCI Host Controller
[ 2.696787] usb usb2: Manufacturer: Linux 4.9.22-wb6_initramfs ehci_hcd
[ 2.703478] usb usb2: SerialNumber: ci_hdrc.1
[ 2.709249] hub 2-0:1.0: USB hub found
[ 2.713242] hub 2-0:1.0: 1 port detected
[ 2.982018] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 3.072035] usb 2-1: new high-speed USB device number 2 using ci_hdrc
[ 3.175747] usb 1-1: New USB device found, idVendor=0951, idProduct=160e
[ 3.182653] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.189921] usb 1-1: Product: DataTraveler 2.0
[ 3.194515] usb 1-1: Manufacturer: Kingston
[ 3.198750] usb 1-1: SerialNumber: 2008012500000000000004BD
[ 3.208015] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 3.215195] scsi host0: usb-storage 1-1:1.0
[ 3.262605] usb 2-1: New USB device found, idVendor=0424, idProduct=2514
[ 3.269379] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.278320] hub 2-1:1.0: USB hub found
[ 3.282467] hub 2-1:1.0: 4 ports detected
[ 3.602052] usb 2-1.1: new high-speed USB device number 3 using ci_hdrc
[ 3.754514] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=b720
[ 3.761518] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.769132] usb 2-1.1: Product: 802.11n WLAN Adapter
[ 3.774243] usb 2-1.1: Manufacturer: Realtek
[ 3.778561] usb 2-1.1: SerialNumber: 00e04c000001
Load modules for USB to work
Starting USB update
Waiting for USB to settle (0/10)
[ 4.244333] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 4.256781] sd 0:0:0:0: [sda] 3930112 512-byte logical blocks: (2.01 GB/1.87 GiB)
[ 4.268383] sd 0:0:0:0: [sda] Write Protect is off
[ 4.274127] sd 0:0:0:0: [sda] No Caching mode page found
[ 4.279528] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 4.407199] sda: sda1
[ 4.413616] sd 0:0:0:0: [sda] Attached SCSI removable disk
umount: can't umount /usb: Invalid argument
Looking for wb6_update_FACTORYRESET.fit on /dev/sda
umount: can't umount /usb: Invalid argument
mount: mounting /dev/sda on /usb failed: Invalid argument
Looking for wb6_update_FACTORYRESET.fit on /dev/sda1
umount: can't umount /usb: Invalid argument
[ 5.125819] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
BusyBox v1.22.1 (Debian 1:1.22.0-19+deb9u2) built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ # ##############################################################################
FACTORY RESET REQUESTED
This WILL destroy ALL YOUR DATA: configuration, scripts,
files in home directory!
If you are ABSOLUTELY SURE that you want to reset Wiren Board
to factory condition, hold the FW button for 4 seconds.
If you will not do it in 10 seconds, the controller will reboot
without firmware update.
If you want to perform a regular firmware update, rename
FIT file to "wbX_update.fit" without "factory-reset" suffix.
##############################################################################
....
Factory reset is confirmed!
===============================================================================
Wed May 24 13:53:26 UTC 2023: started update from /usb/wb6_update_FACTORYRESET.fit
===============================================================================
Description: WirenBoard firmware update
Compatible device: contactless,imx6ul-wirenboard61
Firmware version: 202203251520
Firmware compatible: unknown
Release name: wb-2201
Release suite: stable
Release target: wb6/stretch
Release repo prefix:
Time of creation: Fri Mar 25 15:21:39 UTC 2022
===============================================================================
>>> Checking SHA1 hash of install
PROGRESS: 0%
>>> SHA1 hash of install ok
>>> Wiping data partition (factory reset)
mke2fs 1.43.4 (31-Jan-2017)
ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/mmcblk0p6 is mounted.
[ 13.198955] random: crng init done
Discarding device blocks: done
Creating filesystem with 345344 4k blocks and 86416 inodes
Filesystem UUID: 83e91f1d-1213-4b00-84c7-734d75f23953
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912
Allocating group tables: done
Writing inode tables: done
Creating journal (8192 blocks): done
Writing superblocks and filesystem accounting information: done
>>> Extracting install script
>>> Running install script
...
PROGRESS: 100%
>>> SHA1 hash of rootfs ok
>>> Installing firmware update
>>> Getting mmcpart from U-Boot environment
>>> Will install to /dev/mmcblk0p2
>>> Check if partition table is correct
[ 51.999131] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
>>> Mounting /dev/mmcblk0p2 at /dev/shm/rootfs
[ 52.035440] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
>>> Cleaning up /dev/mmcblk0p2
>>> Cleaning up using rsync
>>> Extracting files to new rootfs
/dev/shm/rootfs /
>>> Recovering device certificates
~ # [ 142.226365] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
~ # [ 142.293082] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
~ #
~ # [ 142.359893] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null)
~ # >>> Mount /dev, /proc and /sys to rootfs
>>> Running post-install scripts
>>> > Processing /dev/shm/rootfs/usr/lib/wb-image-update/postinst/10update-u-boot
Trying to install u-boot using u-boot-install-wb from new rootfs
Das U-Boot installator for Wiren Board
Ну и загружается совершенно штатно. На контроллере был 2304, контроллер WB6.6
wirenboard-ACAX3M6K login: root
Password:
_ _ _
__ _(_)_ __ ___ _ __ | |__ ___ __ _ _ __ __| |
\ \ /\ / / | '__/ _ \ '_ \| '_ \ / _ \ / _` | '__/ _` |
\ V V /| | | | __/ | | | |_) | (_) | (_| | | | (_| |
\_/\_/ |_|_| \___|_| |_|_.__/ \___/ \__,_|_| \__,_|
Welcome to Wiren Board 6.6.0 (s/n ACAX3M6K), release wb-2201 (as stable)
Linux wirenboard-ACAX3M6K 5.10.35-wb105 #1 Wed Feb 2 21:09:31 UTC 2022 armv7l GNU/Linux
Попробуйте выполнить ```print`` из загрузчика, посмотрим что там указано. У меня:
U-Boot SPL 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38)
DRAM init ok, rows:15, ncs:1, size: 512MB
.p0_mpdgctrl0 = 0x0118011c
.p0_mpdgctrl1 = 0x0e3f0e3f
.p0_mprddlctl = 0x3f3f4045
.p0_mpwrdlctl = 0x3f3f3935
.p0_mpwldectrl0 = 0x000b000b
.p0_mpwldectrl1 = 0x000c000c
Trying to boot from MMC1
Warning - USDHC2 controller not supporting
U-Boot 2017.03-wb1.3.0-g520058c326 (Jan 18 2022 - 10:56:38 +0000)
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 61C
Reset cause: WDOG
Model: Wiren Board rev. 6.1 (i.MX6UL)
Board: Wiren Board MX6UL
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@02188000
Hit any key to stop autoboot: 0
=> print
_decr_timeout=setexpr fw_timeout ${fw_timeout} - 1
_led_toggle_state=0
_usb_update_checkbutton=run _usb_update_print_msg ; run led_wait_init ; if run wait_button_up; then if run wait_button_down; then run _usb_update_start; fi; fi
_usb_update_checkfile=if load ${fw_dev} ${loadaddr} ${fw_file} 1 ; then run _usb_update_checkbutton ; elif load ${fw_dev} ${loadaddr} ${fw_reset_file} 1 ; then setenv fw_file ${fw_reset_file}; run _usb_update_checkbutton ; fi
_usb_update_print_msg=echo ; echo '##############################' ; echo '# Detected USB flash drive with update file' ; echo "# Filename: ${fw_file}" ; echo "# Press a FW key if you want to update firmware from this file" ; echo "# or wait 3 seconds to boot normally." ; echo "##############################"
_usb_update_start=run led_fw_init; echo USB update procedure start; run do_usb_update
_wait_loop=run led_wait_toggle ; sleep 0.2 ; run _decr_timeout
abortboot=1
addoverlay=if ${fdt_load_continue} && load mmc ${mmcdev}:${mmcpart} ${fdt_overlay_addr} ${fdt_overlays_dir}/${ovl}.dtbo; then echo Applying DT overlay ${ovl};if fdt apply ${fdt_overlay_addr}; then true; else echo Failed to apply overlay ${ovl};setenv fdt_load_continue false;fi;fi
altbootcmd=if test ${mmcpart} -eq 2; then echo Switching to rootfs on partition 3;setenv mmcpart 3;else; echo Switching to rootfs on partition 2;setenv mmcpart 2;fi;setenv bootcount 0;saveenv; boot
baudrate=115200
board_name=WB
board_rev=6UL
bootcmd=run maybe_usbupdate;mmc dev ${mmcdev};if mmc rescan; then echo SD/MMC found on device ${mmcdev};if run loadbootenv; then run bootenv; fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt; run mmcboot; fi;fi;
bootcount=0
bootdelay=3
bootenv=echo Importing environment from ${loadaddr}...; env import -t ${loadaddr} ${filesize};echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;
bootlimit=3
bootrestore=echo Restoring minimal partition table and bootloader; setexpr RESTOREBOOT_SIZE *$bootrestore_size / 0x200 ; setexpr RESTOREBOOT_START *$bootrestore_start ; mmc write $RESTOREBOOT_START 2 $RESTOREBOOT_SIZE ; mw.l $bootrestore_flag 0 ; led red on ; echo Done! Now do a power cycle ; reset
bootrestore_flag=0x82fffffc
bootrestore_size=0x82fffff8
bootrestore_start=0x82fffff4
console=ttymxc0
do_usb_update=echo Checking if ubootenv part is present; if fsfitxtract ${fw_dev} ${fw_file} ubootenv ${loadaddr}; then run bootenv; else echo Extracting kernel; fsfitxtract ${fw_dev} ${fw_file} kernel ${loadaddr}; echo Extracting DTB; fsfitxtract ${fw_dev} ${fw_file} dtb ${fdt_addr}; setenv optargs ${optargs} bootmode=usbupdate,${fw_f;
eth1addr=04:91:62:c2:41:59
ethaddr=04:91:62:c2:33:30
fdt_addr=0x83000000
fdt_dir=/boot/dtbs
fdt_extra_overlay_offset=0x7e0
fdt_extra_overlay_size=0x20
fdt_file=/boot/dtbs/imx6ul-wirenboard61.dtb
fdt_maxsize=0x20000
fdt_overlay_addr=0x84000000
fdt_overlays_dir=/boot/overlays
fw_dev=usb 0:1
fw_file=wb6_update.fit
fw_reset_file=wb6_update_FACTORYRESET.fit
fw_timeout="14"
ip_dyn=yes
led_fw_init=led green on; led red off;
led_nofw_init=led green off; led red on;
led_wait_init=led red on ; led green on
led_wait_toggle=if test ${_led_toggle_state} -eq 0; then led green on; led red on; else led green off; led red off; fi; setexpr _led_toggle_state ${_led_toggle_state} ^ 1
loadaddr=0x82000000
loadbootenv=load mmc ${mmcdev}:${mmcpart} ${loadaddr} /boot/uEnv.txt
loadfdt=run loadfdtandoverlays
loadfdtandoverlays=mmc read ${fdt_overlay_addr} ${fdt_extra_overlay_offset} ${fdt_extra_overlay_size};if fdt addr ${fdt_overlay_addr}; then setenv fdt_extra_overlay_addr ${fdt_overlay_addr};setexpr fdt_extra_overlay_size_bytes ${fdt_extra_overlay_size} * 0x200;setexpr fdt_overlay_addr ${fdt_overlay_addr} + ${fdt_extra_overlay_size_byte;
loadmainfdt=if test -n ${fdt_file_override} && echo Loading fdt_file_override ${fdt_file_override} && load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file_override}; then true; else if test -n ${fdt_name_factory} && echo Loading factory fdt ${fdt_name_factory} && load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_dir}/${fdt_name_factory}.;
loadzimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} /boot/zImage
maybe_usbupdate=echo Checking if there is a USB storage with update file ${fw_file}; regulator dev usb1_vbus; regulator enable; usb start; if usb storage; then run _usb_update_checkfile ; fi; run led_nofw_init ; echo No USB update detected, continuing boot
mmcargs=setenv optargs ${optargs} root=/dev/mmcblk${mmcdev}p${mmcpart} rootwait ro; run setbootargs
mmcboot=echo Booting from mmc ...; run mmcargs; bootz ${loadaddr} - ${fdt_addr}
mmcdev=0
mmcpart=2
netargs=setenv optargs ${optargs} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp; run setbootargs
netboot=echo Booting from net ...; run netargs; tftp zImage; if ${get_cmd} ${fdt_addr} ${fdt_file}; then bootz ${loadaddr} - ${fdt_addr}; else bootz; fi;
not_timeout=test 0x${fw_timeout} -gt 0
ramboot=echo Programming fuses ...; fuse prog -y 0 5 0x4860; fuse prog -y 0 6 0x10; echo Booting kernel from RAM ...; run setbootargs; bootz ${loadaddr} - ${fdt_addr};
read_button=gpio qi GPIO5_10
setbootargs=setenv bootargs console=${console},${baudrate} ${optargs}
upgrade_available=0
videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0
wait_button_down=until run read_button && run not_timeout ; do run _wait_loop; done; run not_timeout
wait_button_up=while run read_button && run not_timeout ; do run _wait_loop; done; run not_timeout
Environment size: 6596/8188 bytes
=>